power steering Citroen C4 AIRCROSS RHD 2012 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2012, Model line: C4 AIRCROSS RHD, Model: Citroen C4 AIRCROSS RHD 2012 1.GPages: 332
Page 37 of 332
1
35
Monitoring
Screen 1Screen 2CauseSolution - ActionObservations
Warning messages (ignition at "ON")
Fault with the electric power steering. Stop the vehicle, wait few moments
then start the engine again. If the message remains after
restarting, contact a CITROËN
dealer or a quali
fied workshop.
The batter
y for the "Keyless Entry and Starting" system is flat. Replace the battery (see "Changingthe batteries").
The electronic ke
y that you have onyour person is not recognised. Check that you have the correctelectronic key. If the message persists, contact a CITROËN dealer.
The electronic ke
y is still in the
vehicle and you have tried to lock
the doors or boot from the outside. Ensure that
you have the electronickey on your person before lockingthe vehicle.
One of the doors or the boot is not properly closed when locking the
vehicle from the outside. Close the door or the boot, then lock
the vehicle.
Fault with the "Ke
yless Entry andStarting" system. Contact a CITROËN dealer.
Page 108 of 332
106
Driving
Starting - stopping the engine with the key
- Position 1: LOCKThe steering is locked.
- Position 2: ACCThe accessories (radio, 12 V socket...)can be used.
- Position 3: ONIgnition on.
- Position 4: STARTStarting the engine.
Ignition switch
If you use the accessories for aprolonged period (with the key in position 2 (ACC)), you risk dischargingthe battery. Star ting your vehicle will then no longer be possible. Be aware. See the "Automatic power cut-off toaccessories" section.
Key in ignition
A buzzer sounds on opening the driver'sdoor, if the key has been left in the ignition.
)
Inser t the key in the ignition switch. )
Turn the key to position 2 (ACC)
and unlock
the steering column, by turning wheelslightly. ) Press and hold the brake pedal. )
Fully depress the clutch pedal (vehicles fitted with a manual gearbox). )
Put the gear lever into neutral (vehicles fitted with a manual gearbox), or in position P(vehicles fitted with a CVT
gearbox). ) Operate the star ter by turning the key to
position 4 (START). ) Once the engine is running, release thekey.
The key returns automatically to
position 3 (ON).
Starting using the key
Stopping
)Immobilise the vehicle. )Put the gear lever into neutral (vehiclesfitted with a manual gearbox), or inposition P
(vehicles fitted with a CVT gearbox). )While pressing the key, turn it toposition 1 (LOCK). )Remove the key from the ignition switch. )Lock the steering.
Do not attach any heavy objects to the key as this could weigh down on it whenin the ignition switch and cause a fault.
For Diesel vehicles, when the engineis cold wait with the ignition switchin position 3 (ON)
until the preheater warning lamp goes off, before turning
the key to position 4 (START)
. The warning lamp does not come on when the engine is hot.
Page 111 of 332
109
4
Driving
Once the engine has started, you can remove the electronic key from itshousing A
and close the glove box.
Back-up starting with
the electronic ke
y
The message is displayed
when you open the driver's
door and the electronic keyhas not been removed fromits location A. Remember to take the electronic key with you when you leave the vehicle.
) Press the brake pedal on vehicles fitted
with a CVT gearbox or depress the clutch
pedal fully on vehicles with a manual gearbox.
) Press the "STA R T/STOP
" button.
When the electronic ke
y is in the defined zone
and your vehicle does not star t after pressingthe "START/STOP" button: )Open the glove box. )Inser t the electronic key in the location A.
Emergency stop with
the electronic ke
y
During an emergency stop, the braking servo assistance and steering power assistance functions are no longer provided. Take great care.
In the event of an emergency only, theyengine can be stopped without any conditions.
To do this, press and hold the "STA R T/STOP " button for about 3 seconds or make
3 successive presses on the button.
The engine stops and the vehicle goes into
"ACC" mode.
Page 121 of 332
119
4
Driving
Stop & Start (Auto Stop & Go) function
Operation
Going into engine STOP mode
The "AS&G"warning lamp comes on in
the instrument panel or the instrument panel screen and the engine goes intostandby after a few seconds:
- with a manual
gearbox
, with the vehicle stationary and your foot on the brake, whenyou put the gear lever into neutral andrelease the clutch pedal.
Never refuel with the engine in STOPmode; you must switch off the ignition with the key or the START/STOP button.
When the engine is stopped automatically, the operation of certainvehicle systems, such as for example,braking, power steering... are modified. Take care.
Special cases: STOP mode notavailable
STOP mode is not invoked when:
- the driver's seat belt is not fastened,
- the bonnet is open,
- the vehicle has not exceeded 3 mph (5 km/h) since the last engine start,
- the vehicle has restarted less than10 seconds ago,
- the engine is needed to maintain acomfor table temperature in the passenger compartment,
- demisting is active,
- some special conditions (battery charge, engine temperature, braking assistance,
ambient temperature...) where the engine isneeded to assure control of a system.
- th
e "AS&G"warning lamp is
flashing in the instrument panel.
This operation is perfectl
y normal.
The Stop & Star t (Auto Stop & Go) function puts the engine temporarily into standby during stops in the traffic (red lights, traffic jams, or other...).The engine restar ts automatically as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t (Auto Stop & Go) function reduces fuel consumption and exhaust emissions as well as the noise level whenstationary.
Page 198 of 332
196
Practical information
Recovering the vehicle
General
recommendations
Obser ve the legislation in force in your country.
Ensure that the weight of the towing vehicle is higher than that of the towed vehicle.
The person at the wheel of the towed vehicle must have a valid drivinglicence.
When towing a vehicle with all four wheels on the ground, always use anapproved towing bar; rope and strapsare prohibited.
When towing a vehicle with the engine off, there is no longer any power assistance for braking or steering.
In the following cases, you must always call on a professional recovery service:
- vehicle broken down on a motor way or fast road,
- 4 wheel drive vehicle,
- when it is not possible to put thegearbox into neutral, unlock the steering, or release the parking brake,
- towing with only two wheels on the ground,
- where there is no approved towing bar available...
Towing with the wheels on the groundis only possible on 2 wheel drive (2WD) versions.
Recovery of your vehicle
2 wheel drive (2WD) versions: towingwith the wheels on the ground
)Put the gear lever into neutral (position Nfor the CVT gearbox). )Unlock the steering by by turning the
ignition switch to the " ON
" position (or
t
o " ON " mode for vehicle fitted with the
"Keyless Entry and Star ting" system). )Release the parking brake. )Switch on the hazard warning lamps on both vehicles. )Move off gently and travel slowly for a shor t
distance only.
) Fit the towing bar to the towing eye on thechassis, located under the front bumper.