boot Citroen C4 PICASSO 2008 1.G User Guide

12
78
3
56
4
78
12
3
56
4
146
III
B O O T C A R G O N E T - G R A N D C 4 P I C A S S O A N D C 4 P I C A S S O
Cargo net : Grand C4 Picasso
There are 8 anchoring rings in the boot to enable you to secure your loads :
- 1 and 2 underneath the luggage-cover blind.
- 3, 4, 7 and 8 on the boot fl oor.
- 5 and 6 on the boot pillars.
Cargo net : C4 Picasso
There are 8 anchoring rings in the boot to enable you to secure your loads :
- 1, 2, 3 and 4 on the boot fl oor,
- 5, 6, 7 and 8 on the boot pillars.
The cargo net gives you a number of confi gurations depending on which of the anchoring rings you attac h it to (hammock format, vertical / horizontal, on the fl oor or behind the second row seats), enabling you to secure a variety of objects in the boot.
Note : For reasons of safety in the event of sudden braking, it is re commended that you place heavy objects on the fl oor as close as possible to the backrests of the second-row se ats.
Carrier bag hook
A carrier bag hook is available inside the boot on the left hand side.

A
B
III
151
The pneumatic suspension has an additional function associated with it : the possibility to raise or lower the height of the rear of the vehicle when stationary, in or-der to facilitate loading / unloading of the boot.
TO INCREASE THE HEIGHT OF THE BOOT
SILL
- Press continuously at the top of the control A, which is located in the boot, on the left-hand side.
This action will be accompanied by a sound signal. You can stop the movement at any time by releasing the control.
3 beeps will confi rm that the movement has gone as far as it can.
To return to the nominal height :
- Press briefl y twice at the bottom of the control A.
TO DECREASE THE HEIGHT OF THE BOOT SILL
- Press continuously at the bottom of the control A.
This action will be accompanied by a sound signal. You can stop the movement at any time by releasing the control.
3 beeps will confi rm that the movement has gone as far as it can.
To return to the nominal height :
- Press briefl y twice at the top of the control A.
Note :
- If you start the vehicle without having returned it to the nominal height, the automatic correction will ac-tivate as soon as the vehicle starts to move. During the correction, the SERVICE warning lamp lights up and a message on the screen reminds you not to ex-ceed 10 km/h (6 mph).
- The loading assistance does not function in the fo l-lowing instances:
- If the button B is lit up,
- in power economy mode.
- When you fi rst use the function, press for two seconds on the control A to initialise the system. All subsequent ac-Ations will be followed immediately by the desired results.
Driving with the boot sill in a low position may damage th e components located under the bodyshell.
Grand C4 PicassoC4 Picasso
L O A D I N G A S S I S T A N C E

1
23
A
B
VI
185
REAR LENS
Note the bulb that is faulty.
Bulbs
 Direction indicator: PY21W.
 Stoplamp and sidelamp :P21/5W.
 Reversing lamp : P21W.
Rear lamp units on the bodywork
1. With the tailgate open, press on the plastic cover A, located close to the lens, to release it from its housing.2. Undo the two screws B on the side of the lens and detach the lamp by pulling it rearwards.3. Disconnect the connector linking the lens unit with the tailgate.4. Remove the bulb-holder.5. Replace the bulbs. To remove a bulb, rotate it a quarter turn. To refi t the bulb, rotate it a quarter turn in the other direction.6. Reposition the bulb-holder.7. Reconnect the connector to the lens unit.8. Reattach the lamp unit on the body work and do up the two screws.9. Reposition the plastic cover by exerting pressure.
Rear lamps on the tailgate
1. With the boot open, remove the plastic cover on the tailgate.
2. Remove the bulb-holder from its housing.
3. Replace the bulb. To remove a bulb, rotate it a quarter turn. To refi t the bulb, rotate it a quarter turn in the other direction.
4. Reposition the bulb-holder.
5. Refi t the plastic cover.
C H A N G I N G B U L B SR E A R L E N S - C 4 P I C A S S O

3
2
1
4
186
VIREAR LENS
Note the bulb that is faulty.
Bulbs :
 Direction indicator : PY21W.
 Stoplamp : P21W.
 Reversing lamp : P21W.
 Sidelamp : LED
Contact a CITROËN dealer.
Rear lamps
1. With the tailgate open, undo the 3 screws located on the side of the lens unit and pull it rearwards to detach.
2. Disconnect the connector lin-king the lens unit to the boot. Do not disconnect the LEDs.
3. Remove the seal.
4. Remove the bulb-holder.
5. Replace the bulbs. To remove a bulb, rotate it a quarter turn. To fi t the bulb, rotate it a quarter turn in the other direction.
6. Reposition the bulb-holder.
7. Put back the seal.
8. Reconnect the connector to the lens unit.
9. Stow the harness in the open-ing provided in the bodywork.
10. Reattach the lens unit on the bodywork and do up the 3 screws.
Third stoplamp with bulb
1. With the boot open, detach the interior trim.
2. Undo the nuts.
3. Using a thin screwdriver, de-tach the 3 retaining lugs.
4. Remove the lamp via the ex-terior of the tailgate.
5. Remove the bulb-holder.
6. Change the faulty bulb(s).
Check that the vehicle lamps work correctly after each operation.
C H A N G I N G B U L B S
R E A R L E N S - G R A N D C 4 P I C A S S O
Third stoplamp with LED
Contact a CITROËN dealer

2
2
1
188
VIDirection indicators side repeaters in the rear view mirrors
To change the side repeater, press fi rmly downwards on the zone indi-cated by the arrow, then pull out the side repeater bulb.
C H A N G I N G B U L B S
Interior lamp (1)
Detach the cover of the interior lamp 1 with a thin screwdriver close to the button, to access the bulb.
Bulb : W 5 W
Spotlamps (2)
Detach the cover of the interior lamp. To access the bulb, detach the partition for the spotlamp con-cerned, as necessary.
Bulb: W 5 W
Boot lamps
Detach the unit by pushing it rear-wards.
Bulb: W 5 W
Torch
1. Open the tab.
2. Push with a fl at screwdriver in the hole under the tab and re-cover the bulb unit.
3. Open the bulb unit fully to change the bulb.
Bulb: Krypton 3.6V.

12
A
190
VI
The puncture repair kit is a complete system including a compressor and a setting product.
It allows you to temporarily repair the tyre, to enable you to drive to your nearest garage.
Depending on model, it is located either in the boot well or in the compartment under the left hand second-row passenger (open the fl ap by turning the screw a quarter turn).
Using the puncture repair kit
1. Affi x a speed limit sticker on the affected wheel, and one on the steering wheel, to re-mind you that you are driving with a wheel that is only fi t for temporary use.
2. Clip the fl ask 1 on the com-pressor 2.
3. Connect the fl ask 1 to the valve of the tyre to be repaired.
4. Connect the compressor pipe to the fl ask.
5. Connect the electric cable to one of the vehicle’s 12V sockets.
6. Operate the compressor by pressing the button A until the pressure in the tyre reaches 2.0 bars. If you cannot make the pressure attain this level, then the tyre is not repairable.
7. Remove and stow the com-pressor.
8. Drive immediately for a few miles at reduced speed, in or-der for the repair to set.
9. Adjust the tyre pressure to the normal level for the vehicle, checking that there is no air es-caping (no loss of pressure).
10. Drive at reduced speed (80 km/h / 50 mph).
Visit a CITROËN dealer as soon as possible.
You must inform the technician that you have used the puncture repair kit to repair the tyre and give him its user guide.
Warning, the fl ask of puncture repair gel contains ethylene-glycol, a product that is toxic if ingested and irritating for the eyes.
Keep out of reach of children.
After use, do not dispose of the fl ask in the environment, but return it to a CITROËN dealer or alternatively to a recognised recovery facility.
This repair kit is available from a CITROËN dealer.
P U N C T U R E R E P A I R K I T
Note : After use, the fl ask should be stored in a plastic container (provided in the kit), so as not to soil your vehicle with residues of the fl uid.

192
VI
C H A N G I N G A W H E E L
ACCESSING THE SPARE WHEEL
1. Move the third-row seat, right-hand side (7 seater model).
2. Retrieve the extension that is attached to the rear of the seat well.
3. Engage the extension on the pinion located under the carpet in the seat well.
4. Using the wheel brace on the extension to turn the pinion clockwise, release the cable to lower the spare wheel to the ground.
5. Remove the wheel from under the vehicle, disengag-ing the linking plate in the centre of the wheel.
STOWING THE AFFECTED WHEEL
1. It is essential to direct the valve upwards.
2. Pass the linking plate through the centre of the wheel (fi rst removing the central trim on certain al-loy wheels).
3. Turn the pinion anti-clockwise to draw in the ca-ble. First the pinion will turn idly, then the cable will tighten to raise the wheel. Check that the wheel is tight against the vehicle fl oor and not interfering with other nearby components (e.g. the exhaust).
4. Stow the tools and chocks.
With the affected road wheel now under the vehicle fl oor , the vehicle has reduced ground clearance, so take extra care when reversing or driving on uneven surfaces, inclu ding kerbs.
Retrieval of the spare wheel and stowage of the affected road wheel are operations that should be done with the vehicle supported on its wheels, not by the jack.
Note : The pinion to release the spare wheel is located under the boot carpet, on the right hand side in the wheel well for the Grand C4 Picasso and on the left hand side for the C4 Picasso.
Grand C4 PicassoC4 Picasso

VI
195
Any repair or any change of tyre, on a wheel fi tted with a sensor, should be carried out by a CITROËN dealer.Any repair or any change of tyre, on a wheel fi tted with a sensor, Any repair or any change of tyre, on a wheel fi tted with a sensor,
The system may be affected from time to time by interference from radio transmissions on similar frequencies.
This function alerts you in the event of a tyre being defl ated or punctured. For this purpose, sen-sors continuously monitor the con-dition of the vehicle’s wheels.
This system does not absolve the driver of the need to check the tyre pressures regularly.
T Y R E D E F L A T I O N D E T E C T I O N
The SERVICE warning lamp comes on and a ve-hicle outline is displayed, accompanied by a mes-sage and a sound signal. The wheel(s) concerned will be shown fl ashing on the vehicle outline. Check the tyre pressures as soon as possible.
Defl ation warning
The STOP warning lamp comes on and a vehicle outline is displayed, ac-companied by a mes-sage and a sound signal. The wheel(s) concerned will be shown fl ashing on the vehi-cle outline. Stop the vehicle imme-diately, avoiding any violent actions on the steering wheel or brakes.
Puncture
Change the damaged wheel (whether punctured or substan-tially defl ated), have the tyre re-paired as soon as possible, then check the tyre pressures as soon as you can after that.
The wheel affected will no longer be detectable by the alert system if it is in the boot or undergoing re-pair. The spare wheel is not moni-tored by the alert system.
The SERVICE warning lamp comes on and a vehicle outline is dis-played, accompanied by a message and a sound signal. The wheel(s) concerned will be shown as ab-sent on the vehicle outline. If you have not changed a wheel, this in-formation indicates a malfunction-ing of the system.
Consult the CITROËN network to have the defective sensor(s) re-placed.
Wheel not monitored
The defl ation detection system is a driving assistance function which does not relieve the driver from the responsibility to be vigilant.
This system does not absolve the driver of the need to check the tyre pressures on a regular basis (see “Vehicle identifi cation"), to ensure that the vehicle behaves as it should and to avoid prema-ture wear on the tyres, especially when the vehicle is being subject-ed to heavy loads or driven at high speeds.
Do not forget to check the tyre pressure on the spare wheel.

196
VITowing with all wheels on the ground
Towing ring fi xings are placed at the front and at the rear of the vehicle.
To access them:
- at the front : push at top left, then pull on right.
- at the rear : push at bottom, then pull on top.
The cover remains attached to the bumper by means of a tab, so t hat it cannot become lost.
The ignition key should be in position “M” so as to retain steering.
Use a bar with hooks to attach on the towing rings.
If the engine is not running, the steering and braking systems will not be power-assisted.
If towing another vehicle, the latter should be free-wheeling (that is, gearbox in neutral). Failing to respect this point may damage some braking components and lead to the failure of the braking assistance func-tion when the engine is next started.
Removable towing ring
The towing ring is detachable and can be fi tted either at the front or at the rear of the vehicle. It is stowed with the tools either in the storage fl ap under the second-row footwell or (according to equipment) in the boot well.
T O W I N G - L I F T I N G
Advice
In exceptional circumstances, it is permitted to tow the vehicle at low speed over a short distance(depending on local legislation in force).
In all other cases, the vehicle must be transported by a trans-porter.
CAUTION - TOWING A VEHICLE WITH AUTOMATIC TRANSMISSION
Put the selector lever in posi-tion N (neutral).