seats Citroen C4 PICASSO 2008 1.G Owner's Manual

1
2
3
G
F
E
IN BRIEF
I
8
I N T E R I O RT h i r d - r o w s e a t s – G r a n d C 4 P i c a s s o
To return the seats to the upright position
Fold the concertina plates (1 2 3) arranged on each of the third-row seats.
Pull on the black belt F located on the seat backrest.
To stow the seats
Put the three sections of the con-certina plates (1 2 3) to their ver-tical position then pull on the red belt G.
Before moving the third-row seats, return the rigid plates to the upright position and lock them.
Do not leave objects either on or underneath the second-row seats when you are folding them.
Access to third-row seats
Pull on control E located at the top of the second-row seats backrest.
Before moving the third-row seats, do not forget to lock in the rigid plates fi rst (located at the base of the second-row seat backrests).

D
A
C
IN BRIEF
I
9
I N T E R I O R
TO FOLD THE SEATS
From outside
- Pull fi rmly upwards on strap C, as indicated by the red arrow, to unlock the seat ; maintain the pressure until the seat is fully folded.
From the boot - whilst loading, for example (Grand C4 Picasso)
Having fi rstly folded the third-row seats.- Pull on control D to unlock the required seat.
TO RETURN THE SEATS TO
THE UPRIGHT POSITION
Return the rigid plates of the second-row seats to their initial (upright) posi-tion and lock them in position (Grand C4 Picasso).
Raise the backrest and push it back-wards until it locks in position.
RIGID PLATE (Grand C4 Picasso)
A rigid plate is attached to each second-row seat backrest.
To unlock / lock the rigid plate :
- Slide latch A of the plate down-wards, to unlock it.
- Return the plate to the upright position, then slide latch A up-wards to lock it.
Note : Before deploying the rigid plates, check that the second-row seats are slid as far back as pos-sible.
Requirements for third-row passenger seat belts Take care to attach the third-row passenger seat belts on the rings provided for this purpose.Do not attach the belts on the anchoring points marked with a red cross (see illustration above).
Stowing the tongue of the third-row seat belt
T h i r d - r o w s e a t s – G r a n d C 4 P i c a s s o S e c o n d - r o w s e a t s

B
A
C
D
IN BRIEF
I
10
I N T E R I O R
S e c o n d - r o w s e a t s
THE “COMFORT” POSITION
The 3 second-row seats are inde-pendent of each other and are all the same width. They can all be ad-justed to the “comfort” position.
To place the seat(s) in the comfort position
- Pull on control B.
The backrest reclines and the seat base pivots slightly.
To return the seat to its original position
- Pull on control B and allow the seat to come forward.
LONGITUDINAL ADJUSTMENT
Lift up control A, located at the front of the seat, and adjust the seat into the desired position.
Positioning the central seat belt
- Insert tongue C into the buckle on the right, then insert the second tongue D into the buckle on the left.

1
23
IN BRIEF
I
12
G E T T I N G S T A R T E DF r o n t s e a t s
Head restraint
Backrest angle
Seat height adjustment
Lumbar support
Longitudinal adjustment
Armrest
Manual adjustments
Electric adjustments :
Adjustment of seat height and angle, longitudinal adjustment
Adjustment of backrest angle and lumbar support
Driver : memorisation of driving positions
Note : The seats can also be ad-justed on a temporary basis :
- on opening one of the front doors,
- after switching on the ignition.
Heated seat control (located on the inside of the front seats)

AC
BA
IN BRIEF
I
21
P A S S E N G E R S A F E T Y
Deactivation of front passenger airbag
1. Insert key into (A).2. Select "OFF"position.3. Remove key.
CHILD SAFETY
Manual control
The rear doors are locked by op-erating the lever (aperture at an angle).
ISOFIX fi xing system
The 3 second-row rear seats and the front passenger seat of your vehicle are fi tted with regu-lation ISOFIX anchoring points, with 3 rings for each seat position (A B C).
This fi xing system is designed for children weighing up to 18 kg.
Electric control
Pressing on the button prohibits operation of the electric windows and opening of the rear doors from the rear of the vehicle.

100
III
Sensors
The automatic regulation of the air conditioning inside the cabin uses a number of sensors that relieve you of the need to make adjust-ments outside the displayed tem-perature.
Be careful not to obstruct the sun-light sensor located on the dash-board.
Air inlet
Check that the exterior grille for the air inlet, at the bottom of the windscreen, is clean and free of dead leaves, snow, etc.
Air vents
The air vents to the face have grilles and thumbwheels so that you can adjust the air fl ow and direction (up-down, right-left).
Air circulation
Air vents on the fl oor underneath the front seats provide enhanced heating for the rear seat positions : take care not to obstruct them.
Dust fi lter / odour fi lter (active carbon)
There is a fi lter for excluding odours and dust.
This fi lter has to be changed in accordance with the vehicle main-tenance schedule (see the Main-tenance Guide).
Air conditioning
To ensure that your system oper-ates correctly, it is recommended to have it checked regularly.
Water arising from condensation in the air conditioning drains away through a hole provided for this purpose. A pool of water may thus form under the vehicle when sta-tionary.
To keep the air conditioning com-pressor well sealed, it is essential to operate the air conditioning at least once in every month.
To be effective, the air condition-ing should only be used with the windows closed.
If after a lengthy stop in bright sunlight the interior temperature is excessive, ventilate the passen-ger compartment by opening the windows for a few moments, then close them again.
The air conditioning operates by using power from the engine. This results in a slight increase in fuel consumption.
V E N T I L A T I O N - H E A T I N G A I R C O N D I T I O N I N G

1
2
III
111
Heated seats
The front seats can be heated independently. Use the controls on the inner sides of the seats and choose one of the three heat intensities below
0 : Off.
1 : Slight heat.
2 : Medium heat.
3 : Strong heat.
The seat temperature will adjust automatically.
Note : the heated seats only func-tion when the engine is running.
Note : The seats can also be adjusted on a temporary basis :
- on opening one of the front doors.
- after switching off the ignition.
Electric adjustments :
Adjustment of seat height and angle, longitudinal adjustment
Adjustment of backrest angle and lumbar support
Raise or lower the front of control 1 to raise or lower the front of the seat base (on driver’s seat).
Raise or lower the rear of control 1 to raise or lower the seat.
Action control 1 forwards or rearwards to slide the seat forwards / backwards.
Push the top of control 2 forwards or rearwards to adjust the backrest angle.
Raise or lower control 2 to increase or decrease the lumbar support.
F R O N T S E A T S E L E C T R I C A D J U S T M E N T S

III
113
For easy modifi cation of your interior vehicle space, all the rear seats can be individually folded : onto the second-row fl oor, and under the third-row fl oor (in the case of the Grand C4 Picasso). You can then have a load fl oor that is continuous up to the front seat backrests.
7 seats6 seats
5 seats4 seats
Maximum loadspace
5 seats4 seats
3 seatsMaximum loadspace
Examples of seat confi gurations Grand C4 Picasso Examples of seat confi gurations C4 Picasso
R E A R S E A T S

A
B
12
114
III
LONGITUDINAL ADJUSTMENT
Lift the control A, located at the front of the seat, then adjust the seat into the position desired.
THE “COMFORT" POSITION
The 3 second-row seats are inde-pendent of each other and all the same width. They all can have a “comfort" position.
To place the seat(s) in the comfort position
- Pull on the control B.
The backrest reclines and the seat base pivots slightly.
To return the seat to the initial position
- Pull on the control B and allow the seat to come forwards.
IMPORTANT : Always supervise any movements of seats by chil-dren.
REAR HEAD RESTRAINTS
The rear head restraints have two possible positions :
1. a low position for when the seats are not occupied,
2. a high position to ensure pas-senger safety, by raising the restraints to their locking posi-tion.
To lower the head restraints
- Press on the unlocking button.
- Press on the top of the head restraint.
To raise the head restraints
- Pull the head restraint upwards as far as it will go.
- Press on the unlocking button and pull the head restraint up-wards.
S E C O N D R O W S E A T S

C
III
115
Each seat can be folded onto the fl oor to enable you to modify your vehicle’s interior space.
TO FOLD THE SEATS
- Pull fi rmly upwards on strap C, as indicated by the red arrow, to unlock the seat ; maintain the pressure until the seat is fully folded.
- Push the backrest slightly forwards so that the back-rest pivots, folding onto the seat base. The assembly then lowers onto the fl oor.
TO RETURN THE SEATS TO THE UPRIGHT
POSITION
- Raise the backrests and push them rearwards so that they lock in position
PLATES BEHIND THE SECOND ROW
SEATS
Plates below the second row seats provide the bottom of the bootspace with rigidity. They automatically fol-low the seat movements (e.g. longitudinal adjustment, folding).
A storage area is available underneath the plates.
IMPORTANT : Always supervise any movements of seats by children.
S E C O N D R O W S E A T S C 4 P I C A S S O