lock CITROEN C4 PICASSO 2022 Owner's Manual

58
Passenger seat backrest angle
F Pull the control upwards or turn the knob to adjust the backrest.
When the backrest is correctly inclined, release
the control.
To prevent the backrest from suddenly
folding for wards and hitting you, hold the
backrest with your back or hand while you
move the control.
Table position for the front
passenger seat backrest
Check that no object, either on or
underneath the seat, could hinder its
movement.
F

P
lace the head restraint in the low position,
raise the armrest and fold the tray on the
back of the seat.
F

P
ull the control fully up and tip the backrest
forwards.
To return to the normal position, guide the
backrest backwards until it locks into place.
This position, together with that of the rear
seats, allows you to transport long objects
inside the vehicle.
In this position, the backrest can support
a
maximum load of 30 kg.
Electric adjustments
To avoid discharging the battery, carry out
these adjustments with the engine running.
Longitudinal (driver seat)
F Push the control for wards or backwards to
slide the seat.
Backrest angle
F Tilt the control for wards or backwards to adjust the angle of the seat backrest.
Ease of use and comfort

62
Front armrest
Height adjustment
Second row seats
The 3 seats of the 2nd row are independent
and are the same width. Their backrests are
adjustable to adapt the boot load space. F

L

ower the armrest completely.
F

L

ift it again to the desired position (low,
intermediate or high).
F

O

nce it is in the high position, lift it to unlock
it and bring it to the low position.
Longitudinal adjustment
A. Longitudinal adjustment: lift the lever.
B. Tilt angle adjustment: pull the strap and
push the seat back.
C. Folding the seat: give a
firm upward pull
on the strap to unlock the seat.
D. Folding the seat from the back: pull the
strap then push the backrest for ward.
F

L
ift lever A , at the front of the seat cushion
and adjust the seat as required.
Ease of use and comfort

64
From outside the vehicle
From the boot, for example when loading F
G
ive a firm upward pull on strap C , as
shown by the arrow, to unlock the seat;
keep pulling the strap until the seat is
completely folded. Push the backrest
slightly for ward so that the backrest tilts
and folds over the cushion. The seat and
cushion fold down to the floor.
Replacing the seat
F If necessary, straighten the continuity panels of the 2nd row of seats and lock
them.
F

R
aise the backrest and push it back until it
latches into place. Before per forming any operations on the
rear seats, to avoid damage to the seat
belts, make sure that the side belts are
properly tensioned. The central seat belt
must be put away. Secure the buckles
of the three seat belts to their anchoring
points.
Continuity panels
You can fold the second row seat(s) directly
from the boot, after having first folded the third
row seats.
F

P
ull strap D to unlock the desired seat and
give the backrest a
slight push for ward. To
prevent any damage to the mechanism,
strap D will unclip if excessive force is
applied. It is just a
matter of clipping it back
into place to make the system operational
again.
Each seat has a
continuity panel at the bottom
of the backrest, which, once unfolded:
-

a
llows for a continuous loading sur face in
the boot, whatever the position of the seats,
-

p
revents objects from sliding beneath the
2nd row seats.
These continuity panels are not designed
to support a
weight greater than 30 kg.
Ease of use and comfort

65
Getting out of the vehicle
from third row seatsReplacing the seat from
outside the vehicle, with
door open
If passengers are seated in the third row seats:
F

m
anually push the seat and cushion back as
far as it can go; the seat does not return to
the maximum back position, leaving space
free for the third row passengers' legs,
F

f
old the cushion until it locks.
Make sure there is nothing on or under the
cushion of the seat you want to move.
If this system fails (lever E ), the third row
passengers can also get out after having
folded the backrest of the second row
seats using strap D .
Do not let children operate the seats
unsupervised.
F
P
ull lever E . The seat unlocks and the
cushion comes up against the backrest.
F

Ke

ep lever E up by pushing it for wards. The
seat and cushion slide towards the front
seat.
This frees space behind the seat, allowing
the third row seat passengers to get into their
seats.
F

L

ift lever E . The seat unlocks and the
cushion moves up to the backrest.
F

P

ush the backrest holding lever E upwards.
Third row seats
Concertina boards
The two rigid concertina boards, which are built
in to the vehicle, cover the two third row seats,
when these are in the folded away position.
Before moving the seats, make sure that
the trays behind the front row seats are
properly stowed.
Unlocking/Locking the continuity panels
F

B

efore unfolding the continuity panels,
check that the 2nd row seats are moved
back as far as possible.
F

S

lide the latch of the continuity panel
upwards to unlock it.
F

S

traighten out the continuity panel, then
slide the latch downwards to lock it.
Access to third row seats
Third row seats are accessed via the second
row lateral seats.
3
Ease of use and comfort

66
Each of the two boards can support
a maximum load of 100 kg.
Folding the concertina
boards
Pull the strap, the 3 parts of the board fold into
c oncertina form.
When the third row seats are straightened,
these folded concertina boards can be left:
-
ei

ther flat behind the seats,
-

o
r in the vertical position,
thus clearing the inside of the seat as a
storage
space.
Installing the seats Seat storage
F Remove the load space cover.
For more information on the Interior
fittings and particularly on the load space
cover, refer to the corresponding section.
F

S
traighten the continuity panels of the
second row of seats and lock them in place.
F

F
old the concertina board and straighten it
vertically.
F

P
ull strap F , located behind the backrest
of the seat. The backrest tilts backwards
bringing the cushion. The seat locks in the
open position. F
S traighten the continuity panels of the
second row of seats and lock them in place.
F

L
ower the head restraints.
F

C
orrectly position the concertina board
vertically behind the seat.
F

M
ake sure that the seat belts of the 3
rd row
of seats are correctly fastened to the loops
and that they do not have any creases.
F

P

ull strap G , located at the bottom of the
backrest of the seat. The seat is unlocked.
F

T

hen, push the backrest slightly for wards.
The backrest tilts and folds on the cushion.
The folded seat is arranged at the back of
its storage area provided for this purpose.
F

P

ut the concertina boards back above the
folded down seats.
Ease of use and comfort

67
Configuration examples
4 seats
3 seats
Transporting items
7
seats 6
seats
Transporting items
5
seats
4
seats
Before working on the seats of the third
row, straighten the rigid boards of the
seats of the second row and lock them in
place.
Do not try to fold a

seat in the third row
without having opened it until the backrest
is fully locked.
Do not leave objects on the cushion or
below the cushion of the seats of the third
row, when you fold them.
Do not guide strap G when storing the
seat, your may jam your fingers.
Do not let children manipulate the seats
unsupervised.
Seat modular design and
configuration
Configuration examples
5 seats
3
Ease of use and comfort

68
In order to easily adapt your interior
space, you can fold all of the rear seats
individually and fold them onto the second
row floor, and beneath the floor on the
third row. This gives you a continuous load
floor up to the back of the front seats.
Folding or unfolding the seats must only
be done with the vehicle stationary.
Steering wheel adjustment
F When stationary , pull the control lever
to release the steering wheel adjustment
mechanism.
F

A
djust the height and reach to suit your driving
position.
F

P
ush the control lever to lock the steering wheel.
As a safety measure, these adjustments
s hould only be carried out with the vehicle
stationary.
Mirrors
Door mirrors
Each fitted with an adjustable mirror glass
permitting the lateral rearward vision necessary
for overtaking or parking.
They can also be folded for parking in narrow
spaces.
Demisting – Defrosting
Demisting-defrosting of the door
mirrors operates with the engine
running, by switching on the heated
rear screen.
For more information on Rear screen
demist - defrost , refer to the associated
section.
Adjustment
As a safety measure, the mirrors should
b e adjusted to reduce the blind spots.
Objects seen in the mirror are in reality
closer than they appear.
Take this into account when assessing
the distance of vehicles approaching from
behind.
F

M
ove control A to the right or to the left to
select the corresponding mirror.
F

M
ove control B in any of the four directions
to adjust.
F

R
eturn control A to the central position.
Folding
F From outside: lock the vehicle using the
electronic key or the " K eyless Entry and
Starting" system.
F

F
rom inside: with the ignition on, pull
the control A from the central position
rearwards.
Ease of use and comfort

69
Automatic tilting in reverse gear
System which provides a view of the ground
d uring parking manoeuvres in reverse gear.
They return to their initial position:
- a f ew seconds after coming out of reverse gear,
-

o
nce the speed of the vehicle exceeds 6 mph
(10


km/h),
-

o
n switching off the engine.
This function can be activated/deactivated in
the Driving menu of the touch screen.
F

Sel
ect the " Vehicle settings " tab, then
" Comfort " and "Mirror adaptation in
reverse ".
Rear view mirror
Equipped with an anti-dazzle system, which
darkens the mirror glass and reduces the
nuisance to the driver caused by the sun,
headlamps from other vehicles, etc.
Manual model
Adjustment
F
A djust the mirror so that the glass is
directed correctly in the "day" position. F

P
ush the lever to change to the normal
"day" position.
Automatic "electrochrome " model
This system automatically and progressively
changes between day and night use by means
of a

s
ensor measuring the light coming from the
rear of the vehicle.
In order to ensure optimum visibility during
your manoeuvres, the mirror lightens
automatically when reverse gear is
engaged.
Child surveillance mirror
If the mirrors are folded using control A ,
they will not unfold when the vehicle is
unlocked. Pull again on control A .
Unfolding
F From outside: unlock the vehicle using the
electronic key or the " K eyless Entry and
Starting" system.
F

F
rom inside: with the ignition on, pull
the control A from the central position
rearwards.
The folding and unfolding of the door
mirrors using the remote control can be
deactivated by a
CITROËN dealer or
a


qualified workshop.
If necessary, the mirrors can be folded
manually.
With the engine running, on engaging reverse
gear, the mirror glasses tilt downwards.
Day/night position
F P ull the lever to change to the "night" anti-
dazzle position.
3
Ease of use and comfort

78
The average use per cartridge is 3 months
a t the rate of one hour per day.
Removing the diffuser
Inserting the diffuser
F Push button A by turning it a quarter turn
completely to the end.
F

R
emove the diffuser from the dashboard
F

R
eplace your cartridge (see "Replacing
a


cartridge"). After installing or replacing the cartridge:
F

p
ut the diffuser back in its housing,
F
t
urn it a quarter of a turn to the right.
Replacing a cartridge
The diffuser refill includes a cartridge B and its
s ealed cover C .
F

R
emove the protective film D .
F

P
lace the head of cartridge B on the diffuser
button A .
F

T
urn it a quarter turn to lock it on the button
and remove the cover.
F

I
nsert the diffuser in its housing.
You can replace cartridges at any time and
keep the cartridges already started in their
original cover.
Diffuser button
The diffuser button A is independent of the
cartridge. The cartridges are delivered without
the button A .
The diffuser button A can only be fixed into the
central control panel with a
cartridge.
Therefore always keep the button A and
a
cartridge.
Depending on the country, replacement
cartridges are available online or from
CITROËN dealers, as well as any qualified
workshop.
Storage is provided for the cartridges and
covers in the glove box.
Ease of use and comfort

80
Do not attach or hang heavy objects on
the slide rail of the sun visor blinds.
Glove box
Depending on the equipment, it may include
a CD player.
F

T
o open the glove box, raise the handle.
It is illuminated when the lid is opened.
It is cooled by a
ventilation nozzle that can be
closed manually.
It is directly linked to your vehicle's air
conditioning system and is supplied with
fresh air whatever the setting required in the
passenger compartment.
The cooling of your glove box only functions
when the engine is running and the air
conditioning is on.
Portable console
The portable console is a removable storage
space fixed to the low centre console.
It includes a
sliding flap, an open storage
compartment and two cup holders.
Taking out the portable console
Sun visor supports
The window blinds are extended via the sun
visor supports.
Fold the support downwards to avoid glare from
ahead.
In case of glare through the door windows,
release the support from its central fixing and
turn it to the side.
The supports are fitted with a
locking system
on their central fixing when rolling up the
window blind. To remove or replace the
support, it must be positioned vertically.
If it is not fixed to its support, the portable
console must be stored in the boot. It
could turn into a
projectile in the event of
sudden braking or serious impact.
F

P
ull the unlocking control located at the
front of the console.
F

W
ith one hand, lift the front part of the
console.
F

W
ith the other hand, take the rear part to
free the portable console.
Ease of use and comfort