clock Citroen C4 PICASSO DAG 2008 1.G Owner's Manual

B
C
DII
71
EMERGENCY UNLOCKING
In the event of the electronic parking brake malfunctioning o
r the battery running fl at, an emergency manual device can unlock the parking brake.
1. Immobilise the vehicle, with the engine running, by engaging fi rst gear (man-ual gearbox), position P (automatic gearbox) or M or R (6-speed electronic gearbox), then switch off the engine.
Note : if it is impossible to immobilise the vehicle, do not action the control and urgently contact a CITROËN dealer. if it is impossible to immobilise impossible to immobilise
2. Fetch the vehicle blocks and the unlocking device (braided cabl e) from the toolbox (see “Changing a wheel”, paragraph on “Tools”).
3. Immobilise the vehicle by placing blocks at the front and at the rear of one of the rear wheels.
4. Slide the front left-hand seat back as far as possible.
5. Lift up the fl oor plug B in the carpet under the seat.
6. Pierce the tab C on the tube D with the unlocking device.
7. Place the unlocking device in the tube D.
8. Turn the unlocking device clockwise. For safety reasons, it is essentialto continue turning the device as far as it will go or until you hear a knocking noise. The parking brake is released.
9. Remove the unlocking device and store it with the blocks in t he toolbox.
Note : - The operation of the parking brake re-initialises when the ignition is switched off then on again. If the reinitialisation of the parking brake proves impossible, contact a CITROËN dealer.off then on again. If the reinitialisation again. If
- The subsequent time required for application may be longer t han during normal operation.
For safety reasons, after this manoeuvre it is essential to contact a CITROËN dealer urgently to have the plug replaced.Following an emergency unlocking, immobilisation of the vehicle is no longer guaranteed once the manual emergency unlocking has been deployed and the manual control d oes not allow the re-application of your park-ing brake.Take no action, either on control A, or stopping starting the engine while the unlocking device is engaged.Take care not to allow moisture or dust in the proximity of the plug.
E L E C T R O N I C P A R K I N G B R A K E
E M E R G E N C Y U N L O C K I N G

12
3
4
182
VIFRONT LENS
 Dipped beam
 Main beam
 Sidelamp
 Direction indicator
Note : A slight misting may appear on the internal sur-face of the headlamp glass in some climatic conditions (e.g. low temperature or humidity) ; this disappears af-ter the lamps have been on for a few minutes.
C H A N G I N G B U L B SH A L O G E N H E A D L A M P S
Dipped beam
1. Remove the rubber plug.
2. Rotate the bulb-holder a quarter turn anti-clockwise and remove it from its housing.
3. Replace the bulb H7.
4. Reposition the bulb-holder by pushing it in, tight e-ning it by a quarter turn (clockwise).
5. Put back the rubber plug.
Changing a halogen bulb should only be done after the headlamp has been switched off for a few minutes (risk of serious burns).
Do not touch the bulb directly with your fi ngers, use lint-fre e cloths.
It is imperative to use only anti-U.V. type bulbs in order not to damage the headlamp.
When using a high-pressure washer on persistant marks, do not direct at the lamps or their outlines for too long, so as not to damage their coating and their seals.

VI
183
Main beam
1. Remove the rubber plug.
2. Detach the clips by lowering them on each side of the bulb.
3. Pull on t he bulb- holder t o remove it.
4. Replace the bulb H1.
5. Push the bulb-holder back into its housing.
6. Reattach the clips.
7. Put back the rubber plug.
Sidelamp
1. Rotate the bulb-holder a quarter turn anti-clockwise.
2. Remove it from its housing.
3. Replace the bulb H6W.
4. Reposition the bulb-holder.
5.Rotate it a quarter turn clock-wise to reposition in its housing.
Direction indicator
1. The direction indicator bulb is located underneath the main beam bulb. Remove the rub-ber plug.
2. Pull on the bulb-holder to re-move it.
3. Replace the bulb H21.
4. Reposition the bulb-holder in the bracket and push it in.
5. Put back the rubber plug.
C H A N G I N G B U L B SH A L O G E N H E A D L A M P S

12
3
4
184
VI Main beam (H7)
1. Remove the rubber plug.
2. Rotate the bulb-holder a quarter turn anti-clockwise and remove it from its housing.
3. Replace the bulb H7.
4. Reposition the bulb-holder by pushing it in, tighte-ning it by a quarter turn (clockwise).
5. Put back the rubber plug.
FRONT LENS WITH XENON DUAL-FUNCTIONDIRECTIONAL HEADLAMPS
Xenon dual-function headlamp (dipped/main beam)
C H A N G I N G B U L B SX E N O N D U A L - F U N C T I O N H E A D L A M P S
If the headlamp bears this symbol, any operation to change the Xenon dual-function directional headlamp D1S is the preserve of professionals (risk of electrocution).
Contact a CITROËN dealer.
It is recommended to change both bulbs at the same time if one of them is faulty. Sidelamp (see “Halogen headlamps”)
 Direction indicator (see “Halogen headlamps”)
When using a high-pressure washer on persistant marks, do not direct at the lamps or their outlines for too long, so as not to damage their coating and their seals.

192
VI
C H A N G I N G A W H E E L
ACCESSING THE SPARE WHEEL
1. Move the third-row seat, right-hand side (7 seater model).
2. Retrieve the extension that is attached to the rear of the seat well.
3. Engage the extension on the pinion located under the carpet in the seat well.
4. Using the wheel brace on the extension to turn the pinion clockwise, release the cable to lower the spare wheel to the ground.
5. Remove the wheel from under the vehicle, disengaging the linking plate in the centre of the wheel.
STOWING THE AFFECTED WHEEL
1. It is essential to direct the valve upwards.
2. Pass the linking plate through the centre of the wheel (fi rst removing the central trim on certain alloy wheels).
3. Turn the pinion anti-clockwise to draw in the cable. First the pinion will turn idly, then the cable will tighten to raise the wheel. Check that the wheel is tight against the vehicle fl oor and not interfering with other nearby components (e.g. the exhaust).
4. Stow the tools and chocks.
With the affected road wheel now under the vehicle fl oor , the vehicle has reduced ground clearance, so take extra care when reversing or driving on uneven surfaces, inclu ding kerbs.
Retrieval of the spare wheel and stowage of the affected road wheel are operations that should be done with the vehicle supported on its wheels, not by the jack.
Note : The pinion to release the spare wheel is located under the boot carpet, on the right hand side in the wheel well for the Grand C4 Picasso and on the left hand side for the C4 Picasso.
Grand C4 PicassoC4 Picasso