warning light Citroen C4 PICASSO RHD 2012 1.G User Guide

V
98
VISIBILITY
OF XENON HEADLAMPS
This system adjusts the height of the
xenon headlamp beams automati-
cally and when stationary, according
to the load in the vehicle, so as to
avoid causing a nuisance to other
road user.
If a malfunction occurs,
this warning lamp is dis-
played in the instrument
panel, accompanied by
an audible signal and a message in
the screen.
The system then places your head-
lamps in the lowest position.
Do not touch the xenon bulbs.
Contact a CITROËN dealer or a
qualifi ed workshop.
MANUAL HEADLAMP ADJUSTMENT

To avoid dazzling other road users,
the height of the halogen bulb head-
lamps must be adjusted according
to the load in the vehicle. To do this,
turn the control, located below the
dashboard to the right of the driver,
to the appropriate position:

0.
1 or 2 people in the front seats.

-.
3 people.

1.
4 to 7 people.

-.
Intermediate setting.

2.

4 to 7 people + maximum authorised
loads.

-.
Intermediate setting.

3.
Driver + maximum authorised
loads.

The initial setting is position "0".
EXTERIOR SIDE SPOTLAMPS

Switching on

The side spotlamps come on tempo-
rarily:


- when you unlock the vehicle,

- when you press the lighting button
on the remote control,

-
with the automatic guide-me-home
lighting, on switching off the ignition,

- when you remove the key from
the ignition,

- when you open a door,

- when you use the remote control
to locate the vehicle.

V
99
VISIBILITY
DIRECTIONAL LIGHTING
When the dipped or main beam
headlamps are on, this function
enables the light beam to follow the
direction of the road.
The use of this function, coupled
with the xenon headlamps only,
considerably improves the quality of
your lighting when cornering.

with directional lighting


without directional lighting



Programming

The function is activat-
ed or deactivated via
the multifunction screen
confi guration menu.


Operating fault

If a malfunction occurs, this
warning lamp fl ashes on the
instrument panel, accompa-
nied by a message on the
multifunction screen.
Contact a CITROËN dealer or a
qualifi ed workshop.
When stationary or moving at very
low speed or when reverse gear is
engaged, the system is inactive.
The status of the system remains
in the memory when the ignition is
switched off.
On vehicles fi tted with daytime run-
ning lamps, the function is activated if
the lighting stalk is in the "AUTO"
or
"Dipped/main beam headlamps"

position. In position "0"
, the function
is not activated.

VIII
126
SAFETY
DIRECTION INDICATORS


)
Left: lower the lighting stalk
beyond the point of resistance.

)
Right: raise the lighting stalk
beyond the point of resistance.
HAZARD WARNING LAMPS

A visual warning by means of the
direction indicators to alert other
road users to a vehicle breakdown,
towing or accident.












Automatic operation of
hazard warning lamps
When braking in an emergency,
depending on the deceleration, the
hazard warning lamps come on
automatically.
They switch off automatically the
fi rst time you accelerate.


)
You can also switch them off by
pressing the button.








Horn

Audible warning system to alert other
road users to an imminent danger. Selection of the left or right direc-
tion indicators to signal a change of
direction of the vehicle.


)
Press this button, the direction
indicators fl ash.
They can operate with the ignition
off.

)
Press at the lower part of the
fi xed centred controls steering
wheel.
Use the horn moderately and only
in the following circumstances:


- immediate danger,

- approaching a location lacking
visibility.







"Motorway" function



)
Press briefl y upwards or down-
wards, without going beyond the
point of resistance; the direction
indicators will fl ash 3 times.

VIII
128
SAFETY
BRAKING ASSISTANCE
SYSTEMS
Group of supplementary systems
which help you to obtain optimum
braking in complete safety in emer-
gency situations:


- anti-lock braking system (ABS),

- electronic brake force distribu-
tion (EBFD),

- emergency braking assistance
(EBA).


Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the
stability and manoeuvrability of your
vehicle when braking, in particular
on poor or slippery surfaces.

Activation
The anti-lock braking system comes
into operation automatically when
there is a risk of wheel lock.
Normal operation of the ABS may
make itself felt by slight vibration of
the brake pedal.
Operating fault

When braking in an emergency,
press very fi rmly without releasing
the pressure. If this warning lamp comes
on, accompanied by an au-
dible signal and a message
in the screen, it indicates a
malfunction of the anti-lock braking
system which could result in loss of
control of the vehicle when braking.
If this warning lamp comes
on, together with the STOP

and ABS
warning lamps,
accompanied by an audible
signal and a message in the screen,
it indicates a malfunction of the elec-
tronic brake force distribution which
could result in loss of control of the
vehicle when braking.

You must stop as soon as it is
safe to do so.

In either case, contact a CITROËN
dealer or a qualifi ed workshop.

When replacing wheels (tyres and
rims), ensure that they conform to
the manufacturer's recommenda-
tions.











Emergency braking assistance

System which, in an emergency,
enables you to obtain the optimum
braking pressure more quickly, thus
reducing the stopping distance.

Activation
It is triggered by the speed at which
the brake pedal is pressed.
The effect of this is a reduction in
the resistance of the pedal and an
increase in braking effi ciency.
When braking in an emergency,
press fi rmly without releasing the
pressure.

VIII
134
SAFETY





The driver must ensure that passen-
gers use the seat belts correctly and
that they are all restrained securely
before setting off.
Wherever you are seated in the ve-
hicle, always fasten your seat belt,
even for short journeys.
Do not interchange the seat belt
buckles as they will not fulfi l their
role fully.
The seat belts are fi tted with an inertia
reel permitting automatic adjustment
of the length of the strap to your size.
The seat belt is stowed automatically
when not in use.
Before and after use, ensure that the
seat belt is reeled in correctly.
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned
in the hollow of the shoulder.
The inertia reels are fi tted with an
automatic locking device which
comes into operation in the event
of a collision, emergency braking or
if the vehicle rolls over. You can re-
lease the device by pulling fi rmly on
the strap and releasing it so that it
reels in slightly. In order to be effective, a seat belt
must:


- be tightened as close to the body
as possible,

- be pulled in front of you with a
smooth movement, checking
that it does not twist,

-
be used to restrain only one person,

- not bear any trace of cuts or fraying,


- not be converted or modifi ed to
avoid affecting its performance.
Recommendations for children
Use a suitable child seat if the pas-
senger is less than 12 years old or
shorter than one and a half metres.
Never use the same seat belt to se-
cure more than one person.
Never allow a child to travel on your
lap.
In accordance with current safety
regulations, for all repairs on your
vehicle, go to a qualifi ed workshop
with the skills and equipment need-
ed, which a CITROËN dealer is able
to provide.
Have your seat belts checked regu-
larly by a CITROËN dealer or a
qualifi ed workshop, particularly if the
straps show signs of damage.
Clean the seat belt straps with soapy
water or a textile cleaning product,
sold by CITROËN dealers.
After folding or moving a seat or rear
bench seat, ensure that the seat belt
is positioned and reeled in correctly.
In the event of an impact

Depending on the nature and se-
riousness of the impact
, the pre-
tensioning device may be deployed
before and independently of the
airbags. Deployment of the preten-
sioners is accompanied by a slight
discharge of harmless smoke and
a noise, due to the activation of the
pyrotechnic cartridge incorporated
in the system.
In all cases, the airbag warning lamp
comes on.
Following an impact, have the seat
belts system checked, and if neces-
sary replaced, by a CITROËN dealer
or a qualifi ed workshop.

IX
141
DRIVING

To immobilise the vehicle,
engine running
To immobilise the vehicle when sta-
tionary with the engine running, you
must apply the parking brake manu-
ally by pulling
on control lever A
.
The application of the parking brake
is confi rmed by:


- the illumination of warning
lamp P
in control A
and in
the instrument panel,

- the display of a message
"Parking brake on" in the multi-
function screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P

in the instrument panel is
on fi xed (not fl ashing).


Particular situations

In certain situations (e.g. starting
the engine), the parking brake can
automatically alter its force. This is
normal operation.
To move your vehicle without start-
ing the engine (towing, etc...), but
with the ignition on
, press the brake
pedal and release the parking brake
by pulling
then releasing
control
lever A
.
The full release of the parking brake
is confi rmed by the warning lamp P

(red) in the instrument panel going
off and the display of a message
"Parking brake off" in the multifunc-
tion screen.
If the parking brake malfunctions
while applied or if the battery
runs
fl at, an emergency release remains
possible.


Activation/Deactivation of the
automatic functions *

The automatic application when
the engine is switched off and the
automatic release when you press
the accelerator can be deactivated.
Activation/deactivation is performed
using the confi guration menu of the
multifunction screen. To do so, se-
lect "Vehicle parameters/Comfort/
Automatic handbrake".
The deactivation of these
functions is confi rmed by the
lighting of this warning lamp
in the instrument panel.

* According to country With the automatic functions deacti-
vated, the application and release of
the parking brake are done manually.

IX
145
DRIVING


SITUATION



CONSEQUENCES




4

Display of message " Parking brake faulty
"
and the following warning lamps:
and/or fl ashing

- The automatic functions are deactivated.

- Hill start assist is not available.
To apply the electric parking brake:


)
Immobilise the vehicle and switch off the ignition

)
Pull the control lever for at least 5 seconds or until maximum
application.

)
Switch on the ignition and check that the electric parking brake
warning lamps are on.


- Application may take longer than in normal operation.

- If warning lamp P
fl ashes or if the warning lamps do not come
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer or a qualifi ed workshop.
To release the electric parking brake:


)
Switch on the ignition.

)
Pull the control lever and hold it for approximately 3 seconds.


5

Display of message " Parking brake control
faulty – auto parking brake activated
" and
the following warning lamps:
and/or fl ashing

- Only the functions for automatic application on switching off the
engine and automatic release on acceleration are available.

- Manual application/release of the electric parking brake and
dynamic emergency braking are unavailable.


6

Battery fault

- Lighting of the battery warning lamp makes it essential to stop
the vehicle as soon as traffi c allows. Stop and immobilise your
vehicle.

- Apply the electric parking brake before switching off the engine.

IX
153
DRIVING
The Stop & Start system puts the en-
gine temporarily into standby - STOP
mode - during stops in the traffi c
(red lights, traffi c jams, or other...).
The engine restarts automatically -
START mode - as soon as you want
to move off. The restart takes place
instantly, quickly and silently.
Perfect for urban use, the Stop &
Start system reduces fuel consump-
tion and exhaust emissions as well
as the noise level when stationary.

Operation


Going into engine STOP mode
The "ECO"
warning lamp
comes on in the instrument
panel and the engine goes
into standby:


- with the electronic gearbox
system
, at speeds below 4 mph
(6 km/h), press the brake pedal or
put the gear lever in position N
. If your vehicle is fi tted with the sys-
tem, a time counter calculates the
sum of the periods in STOP mode
during a journey. It rests itself to zero
every time the ignition is switched on
with the key.
Special cases: STOP mode not
available

Never refuel with the en-
gine in STOP mode; you
must switch off the ignition
with the key.
For your comfort, during parking
maoeuvres, STOP mode is not
available for a few seconds after
coming out of reverse gear.
STOP mode does not affect the
functionality of the vehicle, such as
for example, braking, power steer-
ing... STOP mode is not invoked
when:


- the driver’s door is open,

- the driver’s seat belt is not fas-
tened,

- the vehicle has not exceeded
6 mph (10 km/h) since the last
engine start using the key,

- the electric parking brake is ap-
plied or being applied,

- the engine is needed to maintain
a comfortable temperature in the
passenger compartment,

- demisting is active,

- some special conditions (battery
charge, engine temperature,
braking assistance, ambient
temperature...) where the engine
is needed to assure control of a
system.
In this case, the "ECO"
warning
lamp fl ashes for a few seconds then
goes off.

This operation is perfectly normal.

IX
163
DRIVING

Deactivation

Press on button 3
.
This action causes the
information "OFF"
to
appear on the instru-
ment panel screen.
This action does not cancel the
memorised maximum speed which
remains displayed in zone A
of the
instrument panel.


Override of the programmed
speed
The accelerator pedal is equipped
with an end-of-travel switch. If you
action this switch by pressing the
pedal hard down, you can exceed
the memorised maximum speed at
any time.
During the time the speed is be-
ing exceeded, the displayed speed
fl ashes.
You have only to release the ac-
celerator pedal to return below the
maximum speed and render the
function active again.

Return to normal driving



)
By moving the control 1
from po-
sition "LIM"
to position 0
.

)
By the engine stopping.
The speed previously chosen is still
memorised.


Operating fault

If there is a speed limiter malfunc-
tion, a message will display accom-
panied by an audible signal and
lighting of the service warning lamp.
Have it checked by a CITROËN
dealer or a qualifi ed workshop. If during the operation of the speed
limiter, the system is unable to keep
within the maximum speed (for ex-
ample on a steep descent or under
heavy acceleration) then the speed
fl ashes. Adapt your speed as neces-
sary.
The function will re-engage when
your speed returns below the de-
sired maximum speed.
On a steep downhill gradi-
ent or on sharp accelera-
tion, the speed limiter will
not be able to prevent the vehicle
from exceeding the programmed
speed.
Use of fl oor mats that are not ap-
proved by CITROËN may hinder
access to the accelerator pedal
and thus interfere with the function-
ing of the speed limiter.
To avoid any risk of interfering with
the pedals:


- check that the fl oor mat is cor-
rectly positioned,

- never use more than one fl oor
mat.

IX
165
DRIVING

Reactivation



)
By recall of the memorised
speed

After a disengagement, press on
button 3
. Your vehicle automati-
cally returns to the memorised
cruise speed which is displayed
in zone A
.
If the memorised cruise speed
is higher than the current speed,
the vehicle will accelerate to
reach the former.

)
By selection of the current
speed

Press on button 2
or 4
once the
desired speed has been reached.
The information "OFF"
will then
disappear from the instrument
panel display.



Overriding the programmed
speed
During the operation of cruise con-
trol, it is always possible to use the
accelerator to go faster than the
cruise speed (for example to over-
take another vehicle). The speed
displayed in zone A
fl ashes.
You have only to release the accel-
erator pedal to return to the cruise
speed. If during the operation of cruise
control, the system is unable to
keep within the memorised speed
(for example on a steep descent),
then the speed fl ashes. Adapt your
speed as necessary.

Return to normal driving
Operating fault
If there is a malfunction, a message
will display accompanied by an audi-
ble signal and lighting of the service
warning lamp.
Have it it checked by a CITROËN
dealer or a qualifi ed workshop.
Cruise control should only
be used when the driving
conditions allow you to drive
at a constant speed.
Do not use it in heavy traffi c, or on
dangerous or slippery roads.
The driver must remain attentive
and in full control of his vehicle.
You are recommended to always
keep your feet within range of the
pedals.
To avoid any risk of interfering with
the pedals:


- check that the fl oor mat is cor-
rectly positioned,

- never use more than one fl oor
mat.

)
By an action on the control 1
from
position "REG"
to position 0
.

)
By the engine stopping.
The cruise speed previously
chosen is no longer memorised.