Injection Citroen C5 2000 (DC/DE) / 1.G Owner's Guide

Downloaded from www.Manualslib.com manuals search engine 126
INJECTION
AIR SUPPLY CIRCUIT SPECIFICATION
Engine : RHY
(1) Air filterPSA 7899.
(2) FlowmeterSIEMENS
(3)Water / recycled gas exchangerVALEO
(4) E.G.R. valvePURFLUX
(5) Turbocharger KKK K03
(6) Air butterflyMAGNETI MARELLI
48W7 Ref. 648
B1HP1A6D

Downloaded from www.Manualslib.com manuals search engine 127
INJECTION
(7) Air / air heat exchanger VALEO.
(8) Turbocharger KKK K03.
(9)EGR valvePURFLUX.
(10)Air butterflyMAGNETI MARELLI
48W7 Ref. 648.
(11)Air filter PSA 7899.
(12) Turbocharging pressure sensorNIPPON DENSO.
AIR SUPPLY CIRCUIT SPECIFICATION
Engine : RHZ
B1HP1A7P

Downloaded from www.Manualslib.com manuals search engine 128
INJECTION
AIR SUPPLY CIRCUIT SPECIFICATION
Engine : 4HX
(1) Air / air exchanger
(2) Air / water exchanger
(3) Warm air metering device BOSCH.
(4) Cold air metering deviceBOSCH.
(5) Turbocharger ALLIEDSIGNAL GT1549P.
(6) FlowmeterSIEMENS.
(7) Air filter PSA 7885.
B1HP1BYP

Downloaded from www.Manualslib.com manuals search engine 129
INJECTION
AIR SUPPLY CIRCUIT SPECIFICATION
Engine : 4HX
ESSENTIAL : Respect the safety and cleanliness
recommendations.
Tool.
[1] Manual vacuum pump: FACOMM DA 16.
Checks.
ESSENTIAL : Respect the safety and cleanliness
recommendations that are specific to high pressure
diesel injection (HDi) engines.
B1HP1ARP

Downloaded from www.Manualslib.com manuals search engine 130
INJECTION
CHECKS : AIR SUPPLY CIRCUIT
Engine : 4HX
Vacuum pump.
- Connect the tool [1] on the vacuum pump (3).
- Start the engine.
- The vacuum should be 0.8 bar at750 rpm.
Boost vacuum regulation electrovalve.
- Connect the tool [1] between the electrovalve (2)and the valve(1).
Compare readings with the values in the table below.
Boost pressure regulation valve.
- Connect the tool [1] on the valve(1).(Grey marking on pipe).
- Appy a vacuum of 0.8 bar. The rod "a"should move 12 ± 2 mm.
- Rod "a"should be moved 12 mm.
«Swirl» control electrovalve.
- Connect the tool[1] as an adaptor between the electrovalve (4)and the control diaphragm of the «Swirl» (5).
- Compare readings with the values in the table below :
«Swirl» control diaphragm.
- Connect the tool[1] on the control diaphragm of the «Swirl» (5).
- Apply a vacuum of approx. 0,6 Bar; the pin (6)should be at the end stop, at «b».
Engine speed (rpm) Vacuum (Bar)
7800.6 Bar
40000.25 Bar
Engine speed (rpm) Vacuum (Bar)
7800.6 Bar
40000.25 Bar

Downloaded from www.Manualslib.com manuals search engine 131
INJECTION
CHECKS : EXHAUST GASES RECYCLING CIRCUIT
Engines : RHZ - RHY
(1) Butterfly housing(3) Electrovalve (black connector)
(2) EGR valve(tube with blue marking)(4) Electrovalve(blue connector)
TOOL
[1] Manual vacuum pump : FACOM DA 16.
ESSENTIAL : Respect the safety and cleanliness requirements specific to
high pressure diesel injection (HDi) engines.
EGR electrovalve
- Check, not under load, between the electrovalve(4)and the EGR valve (2).
- Connect the tool[1] between the electrovalve (3)and the butterfly housing (1).
- Compare readings with the values in the table below.
Butterfly housing electrovalve.
- Check, not under load, between the electrovalve (3)and the butterfly housing (1).
- Connect the tool[1]between the electrovalve(3) and the butterfly housing(1).
- Compare readings with the values in the table below.
Engine speed (rpm) Vacuum value (bar)
7800.5 Bar
25000 Bar
B1HP1BVD

Downloaded from www.Manualslib.com manuals search engine 132
INJECTION
CHECKS : EXHAUST GASES RECYCLING CIRCUIT
Engines : RHZ – RHY
EGR valve
- Connect tool [1]on the EGR valve capsule take-off (2).
- Apply a vacuum of approx.0,6 barto activate the EGRvalve.
- In abruptly suppressing the vacuum, the valve should click and lock itself back on its seating.
- Repeat the operation several times.
Butterfly housing
- Remove the air duct between the air/air exchanger and the butterfly housing (5),(1).
- Connect tool[1]on the butterfly housing vacuum capsule (1).
- Apply a vacuum of approx. 0,8 bar, the flap (a)of the butterfly housing(1)should be closed.
B1HP1BWCB1BP2ADC

Downloaded from www.Manualslib.com manuals search engine CHECKS : EXHAUST GASES RECYCLING CIRCUIT
Engine : 4HX
TOOL
[1] Manual vacuum pump : FACOMM DA 16.
ESSENTIAL : Respect the safety and cleanliness requirements specific to
high pressure diesel injection (HDi) engines..
Electrovalve (EGR).
- Check, not under load, between the electrovalve(3)(blue connector) and the EGRvalve (2)
(tube with blue marking).
- Connect the tool[1]between the electrovalve (3) and the EGRvalve(2).
- Compare readings with the values in the table below.
Butterfly housing electrovalve
- Check, not under load, between the electrovalve (4) (black connector)and the butterfly housing (1)
(Metering pump cold), (tube with white marking).
- Connect the tool[1]between the electrovalve (4) and the butterfly housing(1).
- Compare readings with the values in the table below.
Engine speed (rpm) Vacuum value (bar)
7800.5 Bar
25000 Bar
B1HP1B8D
133
INJECTION

Downloaded from www.Manualslib.com manuals search engine 134
INJECTION
CHECKS : EXHAUST GASES RECYCLING CIRCUIT
Engine : 4HX
EGR valve
- Connect tool[1]on the take-off (a)of the EGR valve capsule (2).
- Apply a vacuum of approx. 0,6 barto activate the EGRvalve.
- In abruptly suppressing the vacuum, the valve should click and lock itself back on its seating.
- Repeat the operation several times.
Butterfly housing
- Remove the air duct between the air/air exchanger and the butterfly housing (1).
- Disconnect the tube (white marking)on the electrovalve (4)(black connector).
- Connect tool[1]on the tube with the white marking.
- Apply a vacuum of approx. 0,8 bar, the flap (b)of the butterfly housing (1) should be closed.
B1BP29NCB1BP29PC

Downloaded from www.Manualslib.com manuals search engine CHECKS : TURBO PRESSURE
Engines : RHY - RHZ
TOOLS.
[1] Pressure gauge for checking boost pressure: 4073-T.A Tool kit 4073-T
[2]Sleeve for checking boost pressure: 4185-T
[3] Adaptor sleeve : 4219-T
Checks.
Preparation for RHY engine
Remove :
- The collars(3).
- The sleeve.
- Insert the tool [2]between the tube(1)and the duct(2).
- Position the tool[1]in the vehicle.
- Connect the pressure gauge[1] to the tool [2]with its tube (a)long enough for
the gauge to be positioned inside the vehicle.
Checks.
Preparation for RHZ engine
- Remove the collar fixing (3).
- Insert the tool [2]equipped with tool[3], between the tube (1)and the duct(2).
- Position the tool [1]in the vehicle.
- Connect the sleeve [2]on the pressure gauge[1]with the tube(a).
BHP12JDB1BP1ZXD
Engine RHZ Engine RHY
135
INJECTION