heating Citroen C5 2009.5 (RD/TD) / 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2009.5, Model line: C5, Model: Citroen C5 2009.5 (RD/TD) / 2.GPages: 314, PDF Size: 19.25 MB
Page 27 of 314
I
29
M O N I T O R I N G
Warning lamp is on Cause Action/Observations
Front
foglamps fi x e d .
The front foglamps are switched on. Turn the ring on the stalk rearwards
twice to switch off the front foglamps.
Rear
foglamps fi x e d .
The rear foglamps are switched on. Turn the ring on the stalk rearwards
to switch off the rear foglamps.
Diesel engine
pre-heating fi x e d . The ignition switch is at the
2nd position (ignition on). Wait until the warning lamp has
switched off before starting. The duration for which the warning lamp is
o n i s d e t e r m i n e d b y t h e c l i m a t i c c o n d i t i o n s .
Parking
brake fi x e d .
The parking brake is applied or not
p r o p e r l y r e l e a s e d . Release the parking brake to switch
o f f t h e w a r n i n g l a m p , k e e p i n g y o u r
foot on the brake pedal.
O b s e r v e t h e s a f e t y r e c o m m e n d a t i o n s .
For further information on the
p a r k i n g b r a k e , r e f e r t o t h e " D r i v i n g "
section.
fl a s h i n g .
T h e p a r k i n g b r a k e i s n o t f u l l y a p p l i e d
or is released.
Passenger's
airbag
system fi x e d . T h e c o n t r o l s w i t c h , l o c a t e d i n t h e
g l o v e b o x , i s i n t h e "
ON " position.
T h e p a s s e n g e r ' s f r o n t a i r b a g i s
activated.
I n t h i s c a s e , d o n o t i n s t a l l a r e a r -
facing child seat. Turn the control switch to the "
OFF "
position to deactivate the front
p a s s e n g e r ' s a i r b a g .
I n t h i s c a s e y o u c a n i n s t a l l a r e a r -
facing child seat.
T h e p a s s e n g e r ' s a i r b a g s y s t e m i s
a u t o m a t i c a l l y p u t i n t o s e r v i c e o n
starting the vehicle (" ON " position).
Page 45 of 314
III
46
C O M F O R T
Air conditioning
We recommend use of the automatic
regulation of the air conditioning.
It permits automatic and optimised
control of all of the following func-
t i o n s : a i r fl o w , t e m p e r a t u r e i n t h e
passenger compartment and air
distribution, by means of various
sensors (ambient temperature, sun-
shine). This eliminates any need for
you to change your settings other
than the temperature value dis-
played.
Take care not to cover the sun-
shine sensor A .
If you select the automatic mode (by
pressing the "AUTO" control) and leave
all of the vents open, optimum comfort
will be maintained and humidity and
condensation will be removed regard-
less of the exterior climatic conditions.
The temperature in the passenger
compartment can only be lower than
the ambient temperature if the air
conditioning is on.
HEATING, VENTILATION AND AIR CONDITIONING RECOMMENDATIONS
In order to be effective, the air con-
ditioning must be used with the win-
dows closed. If the vehicle has been
parked in the sun for a long period
and the interior temperature is very
h i g h , fi r s t v e n t i l a t e t h e p a s s e n g e r
compartment with the windows
open for a few minutes, then close
the windows.
To keep the air conditioning system
in good working order it is essential
that it is operated at least once a
month.
The air conditioning uses engine
power during its operation. As a re-
sult, the fuel consumption of the ve-
hicle increases.
In certain cases of particularly ardu-
ous use (e.g. towing the maximum
load on a steep gradient in high
temperatures), switching off the air
conditioning saves engine power
and improves the towing capacity.
Air inlet
Check that the exterior grille for the
air inlet, at the bottom of the wind-
screen, is clean and free of dead
leaves, snow, etc.
When washing the vehicle using a
high pressure nozzle, avoid spraying
at the air inlet. Air circulation
Maximum comfort is obtained by
means of a good distribution of air in
the passenger compartment, both in
the front and in the rear.
To obtain a uniform distribution of
air, take care not to block the ex-
terior air intake grille located at the
base of the windscreen, the vents,
the air outlets under the front seats
and the air extractor located behind
t h e fl a p s i n t h e b o o t .
T h e f r o n t a n d r e a r v e n t s a r e fi t t e d
with thumbwheels to adjust the air
fl o w a n d d i r e c t i o n . W e r e c o m m e n d
that you leave all of the vents open.
Dust filter/Odour filter
(active carbon)
T h e r e i s a fi l t e r f o r e x c l u d i n g o d o u r s
and dust.
T h i s fi l t e r m u s t b e c h a n g e d i n l i n e
with the vehicle's servicing schedule
(see: "Maintenance and Warranty
Guide").
Page 53 of 314
III
54
C O M F O R T
PROGRAMMABLE HEATING
The programmable heating operates
independently of the engine.
When the engine is off, it pre-heats
t h e c o o l a n t c i r c u i t i n o r d e r t o b e n e fi t
from an optimum engine operating
temperature from the time the en-
gine is switched on.
The programmable heating system
is switched on using the long range
remote control. Activation can be im-
mediate or deferred by means of a
programming function. Programming remote control
The heating system programming
remote control consists of the fol-
lowing buttons and displays:
1. Scrolling functions menu buttons.
2. Function indicator lights: clock,
temperature, operating time, pro-
grammed time, heater operation,
heating management symbols.
3. Digital displays: time, tempera-
ture, duration of operation, pro-
grammed time or level of heating.
4. Off button.
5. On button.
Displays on the remote
control screen Press the buttons
1 in succession to
display the functions.
T h e fi r s t p r e s s o f t h e l e f t - h a n d o r
right-hand button displays the time.
Next, the left-hand button permits ac-
cess to the programming time then to
the level of heating (C1 to C5).
The right-hand button permits ac-
cess to the passenger compartment
temperature then to the duration of
operation of the heater if it is to be
switched on immediately.
If a malfunction of the program-
mable heating system occurs,
contact a CITROËN dealer. Displaying the functions
The passenger compartment tem-
perature information is only avail-
able when the engine is off.
Page 55 of 314
III
56
C O M F O R T
Programming the heating
You must programme your depar-
ture time in order for the system to
calculate the optimum heater start
time automatically.
Programming the departure time
Press the buttons 1 to display the
programming time. Activation - deactivation
Once the programming time has
been displayed by means of the but-
tons
1 , press button 5 (ON) until the
message "OK" appears.
This symbol is displayed.
Once the programming time has
been displayed, press buttons 4 and
5 simultaneously within 10 seconds.
T h i s s y m b o l fl a s h e s .
Set the time by pressing the buttons 1
and press buttons 4 and 5 simultane-
ously to save it.
T h i s s y m b o l i s d i s p l a y e d ( fi x e d ) .
This symbol is displayed when
the heater starts.
HTM: Heat Thermo Management.
When the signal has been re-
ceived, the message "OK" is
displayed along with the symbol
"HTM" .
To deactivate the programming, press
button 4 (OFF) until the message
"OK" appears.
The symbol "HTM" is switched off.
When carrying out these operations,
if the message "FAIL" appears,
the signal has not been received.
Repeat the procedure after chang-
ing your location.
Switching off the heating
Press button 5 (ON).
The symbol "HTM" remains on.
Changing the level of heating
The system offers 5 levels of heat-
ing (from the lowest level C1 to the
highest level C5 ).
Once the level of heating has been
displayed by means of the buttons 1 ,
press buttons 4 and 5 simultaneously.
The letter "C" fl a s h e s .
Set the level of heating by pressing
the buttons 1 .
Press buttons 4 and 5 simultane-
ously to save the level selected. The
letter "C" i s d i s p l a y e d ( fi x e d ) .
The factory pre-sets are replaced
by the new settings entered. The
programmed times are stored until
the next time they are changed.
When the departure time is acti-
vated, the level of heating cannot
be changed. The departure time
m u s t b e d e a c t i v a t e d fi r s t .
Page 56 of 314
III
!
57
C O M F O R T
Changing the battery
The remote control is supplied by a
6 V-28L battery, which is supplied.
Information on the display indicates
when it is time to replace this battery.
Unclip the casing then replace the
battery.
The remote control must then be re-
initialised, see below. Always switch off the program-
m a b l e h e a t i n g w h i l e fi l l i n g w i t h
f u e l t o a v o i d a n y r i s k o f fi r e o r e x -
plosion.
To avoid any risk of poisoning and
asphyxiation, the programmable
heating must not be used, even
for short periods, in an enclosed
space such as a garage or work-
shop which is not equipped with an
exhaust gas extraction system.
Do not park the vehicle on an
i n fl a m m a b l e s u r f a c e ( d r y g r a s s ,
dead leaves, paper…), there is a
r i s k o f fi r e .
The programmable heating sys-
tem is supplied by the vehicle's fuel
tank. Before use, ensure that the
q u a n t i t y o f f u e l r e m a i n i n g i s s u f fi -
cient. If the fuel tank is at the re-
serve, we strongly advise that you
do not programme the heating.
Do not discard the used bat-
teries, take them to an ap-
proved collection point.
Reinitialising the remote control
If the vehicle's battery is disconnect-
ed or the remote control's battery is
replaced, the remote control must
be reinitialised.
After switching on the power, press
button 4 (OFF) for 1 second within
the next 5 seconds. If the operation
has taken place correctly the mes-
sage "OK" is displayed on the re-
mote control screen.
If a problem occurs, the message
"FAIL" appears. Repeat the operation.
In addition, your programmable
heating can be used to pre-heat
your vehicle’s passenger com-
partment. The interior volumetric protection
alarm movement sensor may be
d i s t u r b e d b y t h e fl o w o f a i r f r o m
the programmable heating when
it is in operation.
To avoid any unexpected trigger-
ing of the alarm during use of the
programmable heating, it is ad-
visable to deactivate the interior
volumetric protection.
Page 59 of 314
III
60
C O M F O R T
This function provides the driver with
a back massage. It only operates
when the engine is running.
Press on button A .
The warning lamp comes on and the
massage function is activated for a
period of 1 hour. During this time,
massage is performed in cycles of
6 minutes (4 minutes of massage fol-lowed by 2 minutes break). In total,
the system will perform 10 cycles.
After 1 hour, the function is deacti-
vated. The warning lamp goes out.
Massage function The Welcome function
The welcome function assists entry
and leaving the vehicle.
After switching off the ignition and
opening the driver’s door, the seat
moves back automatically and then
stays in this position, ready for the
next entry to the vehicle.
When switching on the ignition, the
seat moves forward to the memo-
rised driving position.
When moving the seat, take care
that no person or object hinders the
automatic movement of the seat.
This function is deactivated by de-
fault. You may activate or deactivate
this function using the "Main Menu"
on the instrument panel screen. To
do so, select "Vehicle parameters/
Comfort/Driver welcome".
Deactivation
You can deactivate the massage
function at any time by pressing on
button A .
Heated seats control
With the engine running, the front
seats can operate separately.
Use the corresponding adjust-
ment dial, placed on the outer
side of each front seat, to switch
on and select the level of heating
required:
0 : Off.
1 : Low.
2 : Medium.
3 : High.
Page 150 of 314
IX
132
D R I V I N G
5-SPEED MANUAL GEARBOX
Starting the vehicle
Check that the gear lever is in
neutral.
Do not touch the accelerator.
For Diesel engines: turn the
key to position M and wait until
the pre-heating warning lamp
switches off if it has come on.
Operate the starter, turning the
key until the engine starts (no
more than ten seconds).
In temperatures lower than 0 °C,
declutch while operating the
starter to facilitate starting. Engaging reverse gear
Push the gear lever to the right
then rearwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
6-SPEED MANUAL GEARBOX
Engaging reverse gear
Raise the ring under the knob
(indicated by the arrow) and
push the gear lever to the left
then forwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
As a safety precaution and to facili-
tate starting of the engine:
- always select neutral,
- press the clutch pedal.