Citroen C5 2012 (RD/TD) / 2.G Owner's Manual
Manufacturer: CITROEN, Model Year: 2012, Model line: C5, Model: Citroen C5 2012 (RD/TD) / 2.GPages: 316, PDF Size: 9.75 MB
Page 181 of 316
XI
!
179
PRACTICAL INFORMATION
Removing a wheel
)
Park the vehicle on stable, fi rm
ground that is not slippery. apply
the parking brake.
)
If your vehicle is equipped with
"Hydractive III+" suspension,
with the engine running at idle,
adjust the ground clearance to
its maximum height.
)
Switch off the ignition and en-
gage fi rst gear or reverse gear
depending on any slope (for a
vehicle with automatic gearbox,
select position P
).
)
If your vehicle is fi tted with
"Hydractive III+" suspension,
position the chock, whichever di-
rection the gradient may be in, in
front of the front wheel diametri-
cally opposite to the one to be
replaced.
)
Position the jack at one of the four
jacking-points provided on the un-
derbody close to the wheels, then
use the wheelbrace to unwind the
jack until it reaches the ground.
)
Remove the protector from each
bolt using tool 3
.
)
Slacken the wheel bolts.
Before positioning the jack:
)
Always adjust the vehicle’s
ground clearance to the "maxi-
mum height" position and re-
tain this adjustment for as long
as the jack is under the vehicle
(do not use the hydraulic ad-
justments),
)
Immobilise your vehicle on hor-
izontal, stable and non-slippery
ground,
)
Ensure that any passengers
have left the vehicle and are in
a safe place .
Never get underneath the vehicle if
it is supported only by the jack.
The jack and all of the tools are
specifi c to your vehicle. Do not use
them for any other applications.
Have the original wheel repaired
and refi tted as soon as possible.
)
Continue to extend the jack until
the wheel is a few centimetres
off the ground.
)
Undo the bolts, remove the wheel.
Page 182 of 316
XI
!
180
PRACTICAL INFORMATION
Wheel for temporary use
Your vehicle may be fi tted with a
spare wheel which is different to
those on the vehicle. When fi tting
the spare wheel, it is normal to no-
tice that the wheel bolt washers do
not come into contact with the wheel
rim. The spare wheel is secured by
the conical tapering of the wheel
bolt’s shaft.
When refi tting the original wheel,
ensure that the wheel bolt contact
surfaces are clean and in good con-
dition.
Fitting a wheel
)
Fit the wheel on the hub, using
the centring guide. Make sure
that the contact surface between
the hub and the wheel is clean.
)
Screw in the bolts but do not fully
tighten them.
)
Lower the jack and remove it.
)
Tighten the wheel bolts, using
the wheelbrace.
)
Refi t the protectors on the bolts.
)
Return the ground clearance to
the normal position.
)
Ensure the tyre pressure is correct
and have the balancing checked.
Under-inflation detection
These wheels have tyre pressure
sensors. Repairs must be carried
out by a CITROËN dealer or a quali-
fi ed workshop.
Security bolts (according to
version)
Each wheel is equipped with one se-
curity bolt.
To remove it:
)
Remove the protector using tool 3
.
)
Use the security socket with the
wheelbrace.
If your vehicle is fi tted with a
spare wheel of a different size
to those on the vehicle, you
must not exceed 50 mph (80 km/h)
whilst using the spare wheel.
The wheel bolts are specifi c to the
type of wheel.
If the type of wheel is changed,
check with your CITROËN dealer
or a qualifi ed workshop that the
wheel bolts are compatible with the
new wheels.
Take care to note down the code
number engraved on the head of
the security bolt socket. This will
enable you to obtain a replace-
ment security bolt socket from your
dealer.
Page 183 of 316
XI
!
181
PRACTICAL INFORMATION
CHANGING A BULB
Front lamps
Model with Xenon headlamps (D1S)
1.
Dual-function Xenon
headlamps (dipped/main):
D1S
2.
Cornering lighting:
HP19
3.
Daytime running lamps /
sidelamps (LEDs)
For the maintenance of the front lamps
and changing HP19 and D1S bulbs
and LED lamps, contact a CITROËN
dealer or a qualifi ed workshop.
Risk of electrocution
Xenon bulbs must be replaced by
a CITROËN dealer or a qualifi ed
workshop.
You are advised to change both
D1S bulbs at the same time, if one
of them has failed. The headlamps are fi tted with
polycarbonate glass with a
protective coating:
)
do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,
)
use a sponge and soapy water,
)
when using a high pressure
washer on persistent marks, do
not keep the lance directed to-
wards the lamps or their edges
for too long, so as not to dam-
age their protective coating and
seals,
)
do not touch the bulb directly
with your fi ngers, use lint-free
cloths.
Changing a bulb should only be
done after the headlamp has been
switched off for a few minutes (risk
of serious burns).
It is imperative to use only anti-
ultraviolet (UV) type bulbs in order
not to damage the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specifi cation.
Page 184 of 316
XI
182
PRACTICAL INFORMATION
Main beam headlamps
)
Remove the protective cap A
.
)
Disengage the retaining spring.
)
Remove the bulb and replace it,
paying attention to the direction
of fi tting.
)
Refi t the retaining spring.
)
Refi t the protective cap A
.
Model with halogen headlamps
1.
Main beams:
H1
2.
Dipped beams:
H7
3.
Directional lighting:
H7
4.
Daytime running lamps /
sidelamps (LEDs)
For the maintenance of the front lamps
and changing LED lamps, contact a
CITROËN dealer or a qualifi ed work-
shop.
Page 185 of 316
XI
183
PRACTICAL INFORMATION
Dipped beam
headlamps
)
Remove the protective cap B
.
)
Disconnect the connector by
pressing it between the thumb
and index fi nger.
)
Free the bulb from its two metal
clamps.
)
Take out the bulb.
)
Replace the bulb, exerting a slight
axial force.
)
Refi t the connector, until it is all
the way in.
)
Refi t the protective cap B
.
Directional lamp
)
Remove the protective cap C
.
)
Disconnect the connector by
pressing it between the thumb
and index fi nger.
)
Free the bulb from its two metal
clamps.
)
Take out the bulb.
)
Replace the bulb, exerting a
slight axial force.
)
Refi t the connector, until it is all
the way in.
)
Refi t the protective cap C
.
Page 186 of 316
XI
184
PRACTICAL INFORMATION
Front foglamps
)
Remove the fi xing screw of
cover A
using a torx tool, tip the
cover over and remove.
)
Remove the fi xing screw of
lamp B
using a torx tool and pull
the headlamp unit to remove it
from the bumper.
)
Disconnect the connector D
.
)
Remove the bulb by performing
a quarter of a turn.
)
Replace the bulb.
)
Refi t the connector D
.
)
Refi t the headlamp unit in the
bumper.
)
Refi t the lamp screws.
)
Position the cover using its
guides and refi t the screws.
Bulbs:
H8
Direction indicators
)
Remove the fi xing screw of
cover A
using a torx tool, tip the
cover over and remove.
)
Remove the fi xing screw of
lamp B
using a torx tool and pull
the headlamp unit to remove it
from the bumper.
)
Detach the bulb C
by pressing
on bars 1
and 2
.
)
Disconnect the connector (pull
whilst pressing on the grey
tongue using a fl at screwdriver).
)
Replace the bulb.
)
Refi t the connector (push the
grey tongue in well).
)
Refi t the headlamp unit in the
bumper.
)
Refi t the lamp screws.
)
Position the cover using its
guides and refi t the screws.
Bulbs:
HP24W
Page 187 of 316
XI
185
PRACTICAL INFORMATION
The side repeater is sealed.
If the bulb is faulty, replace the side
repeater.
Contact a CITROËN dealer or a
qualifi ed workshop.
Side repeaters
Rear lamps (Saloon)
Identify the failed bulb.
1.
Brake lamps and sidelamps:
P 21 W / 5 W
2.
Sidelamps:
R 5 W
3.
Reversing
lamps
:
H 21 W
4.
Foglamps:
H 21 W
5.
Direction indicators:
PY 21 W
)
Open the boot.
)
Using a fl at screwdriver, remove
the 3 clips which fi x the trim in
the lamp area.
)
Partially remove the trim F
.
)
Disconnect the connector G
.
Boot-mounted lamps
)
Unclip the bulb holder H
.
)
Replace the bulb.
)
Refi t the bulb holder H
.
)
Check that the bulb holder H
is se-
cured correctly by the two clips 6
.
)
Refi t the connector G
.
)
Replace and fi x the trim F
with its
clips.
When refi tting, take care not to
trap the electrical cables.
Page 188 of 316
XI
186
PRACTICAL INFORMATION
Wing-mounted lamps
)
Remove the lateral boot trim
fl ap A
. To do so, pull it towards
the inside of the boot, then pull it
upwards.
)
Disconnect connector B
.
)
Unscrew the 2 fi xings C
.
)
Remove the lamp from its housing.
)
Detach the bulb holder D
.
)
Replace the bulb.
)
Refi t the bulb holder D
.
)
Place the lamp in its housing.
)
Screw in the 2 fi xings C
.
)
Refi t connector B
.
)
Refi t the trim A
.
You can use the wheelbrace to
screw or unscrew the fi xings C
.
Page 189 of 316
XI
187
PRACTICAL INFORMATION
Boot-mounted lamps
)
Open the boot.
)
Using a fl at screwdriver, remove
the plastic cover F
.
)
Disconnect the connector G
.
)
Unscrew the fi xing nut H
.
)
Disengage the lamp from its
housing.
Rear lamps (Tourer)
Identify the failed bulb.
1.
Brake lamps and sidelamps:
P 21 W / 5 W
2.
Sidelamps:
R 5 W
3.
Reversing
lamps
:
H 21 W
4.
Foglamps:
H 21 W
5.
Direction indicators:
PY 21 W
)
Unclip the bulb holder J
.
)
Replace the bulb.
)
Refi t the bulb holder J
ensur-
ing that it is correctly clipped in
place.
)
Position the lamp in its housing.
)
Tighten the fi xing nut H
.
)
Refi t the connector G
.
)
Position and clip in place the
plastic cover F
.
You can use the wheelbrace to screw
or unscrew the fi xing nut H
.
Page 190 of 316
XI
188
PRACTICAL INFORMATION
Wing-mounted lamps
Remove the lateral boot trim A
.
To do so:
)
Pull it towards towards the inside
of the boot.
)
Pull it upwards.
)
Disconnect the connector B
.
)
Unscrew the fi xing nut C
.
)
Remove the lamp from its housing.
)
Detach the bulb holder D
.
)
Replace the faulty bulb.
)
Refi t the bulb holder D
.
)
Place the lamp in its housing.
)
Screw in the fi xing nut C
.
)
Refi t the connector B
.
)
Refi t the trim A
.
You can use the wheelbrace to screw
or unscrew the fi xing nut C
.