display Citroen C5 RHD 2012 (RD/TD) / 2.G Owner's Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2012, Model line: C5 RHD, Model: Citroen C5 RHD 2012 (RD/TD) / 2.GPages: 340, PDF Size: 39.41 MB
Page 119 of 340
VIII
11 7
SAFETY
TYRE UNDER-INFLATION
DETECTION
System which automatically checks
the pressures of the tyres while
driving.
Tyre pressures OK display
Choice of detection
This function provides warning of
tyres that are under-infl ated or punc-
tured.
Automatic detection
Sensors monitor the tyre pressures.
In the event of an anomaly, a mes-
sage will appear in the instrument
panel screen.
Driver request detection
You can check the tyre pressures at
any time.
)
Press on button A
(CHECK); the
information will be displayed in
the instrument panel screen.
)
Press on button A
(CHECK).
The system indicates to you that the
tyres are correctly infl ated.
This information is only available on
request by the driver.
Under-inflated tyre
automatic detection
detection on request
Automatic detection:
A message indicates which tyre is
under-infl ated.
Driver request detection:
The vehicle outline indicates the un-
der-infl ated tyre(s).
The message is accompanied by il-
lumination of the SERVICE
warning
lamp and an audible beep.
)
Check the tyre pressures as
soon as possible.
Page 131 of 340
IX
!!
129
DRIVING
ELECTRIC PARKING BRAKE
The electric parking brake combines
2 operating modes:
- AUTOMATIC
Automatic application when the
engine stops and automatic re-
lease on use of the accelerator
(automatic operation by default),
- MANUAL
Manual application/release of the
parking brake is always possible
by pulling control lever A
while
pressing the brake pedal.
Automatic operation
Application with the engine off
With the vehicle stationary, the park-
ing brake is automatically applied
when the engine is switched off.
The application of the parking brake
is confi rmed by:
Application with the engine running
With the engine running and the ve-
hicle stationary, in order to immobi-
lise the vehicle you need to manually
apply the parking brake by pulling
on control lever A
.
The application of the parking brake
is confi rmed by:
- warning lamp P
in the
control lever A
coming on,
Before leaving the vehicle,
check that warning lamp P
and the warning lamp in the
instrument panel are on fi xed (not
fl ashing).
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
- display of a message "hand-
brake on" in the instrument panel
screen.
The noise of operation will confi rm
to you the application/release of
your electric parking brake.
- warning lamp P
in the
control lever A
coming on,
- display of a message "hand-
brake on" in the instrument panel
screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P
and the warning lamp in the
instrument panel are on fi xed (not
fl ashing).
-
this warning lamp in the in-
strument panel coming on,
- this warning lamp in the in-
strument panel coming on,
Page 132 of 340
IX!
!
130
DRIVING
Release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
)
with a manual gearbox
(fi rst
gear or reverse gear engaged),
press down fully on the clutch
pedal then press on the accel-
erator pedal and move off.
)
with an automatic gearbox
, ac-
celerate with the selector in posi-
tion D
, M
or R
.
Full release of the parking brake is
confi rmed by:
- warning lamp P
in the
control lever A
going off,
- display of a message "hand-
brake off" in the instrument panel
screen.
When stationary, with the engine
running, do not press the accelera-
tor pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake.
Do nat place any object (packet of
cigarettes, telephone...) between the
gear lever and the electric parking
brake control.
Activation/Deactivation of the
automatic functions
Depending on the country of sale,
automatic application when switch-
ing off the engine and automatic
release when moving off can be de-
activated. The activation/deactiva-
tion is done in the instrument panel
screen confi guration menu. Select
"Vehicle parameters/Comfort/Auto
handbrake".
Deactivation of these func-
tions is signalled by this
warning lamp in the instru-
ment panel.
With the automatic functions deac-
tivated, the parking brake must be
applied and released manually.
In some special circumstances,
with the engine not running,
(towing, icy conditions...) the au-
tomatic parking brake can be re-
leased manually, with the key in
the running position.
Manual operation
Manual application/release of the
parking brake is always possible.
Application
With the vehicle stationary, to apply the
parking brake whether the engine is
running or off, pull
on control lever A
.
The application of the parking brake
is confi rmed by:
- warning lamp P
in the
control lever A
coming on,
- display of a message "hand-
brake on" in the instrument panel
screen.
When the driver’s door is opened
with the engine running, a mes-
sage is displayed accompanied
by an audible signal if the parking
brake has not been applied.
-
this warning lamp in the in-
strument panel coming on,
- this warning lamp in the
instrument panel going off,
If the confi guration menu does not
have the option to activate/deacti-
vate the automatic functions, this
can be done by a CITROËN dealer
or a qualifi ed workshop.
Page 133 of 340
IX
!
131
DRIVING
Release
With the ignition on or the engine
running, to release the parking
brake, press on the brake pedal,
push then release
control lever A
.
The full application of the parking
brake is confi rmed by:
- warning lamp P
in the
control lever A
going off,
- display of a message "parking
brake released" in the instru-
ment panel screen.
If you push control lever A
without
pressing the brake pedal, the park-
ing brake will not be released and
the message "Apply foot on brake"
will be displayed on the instrument
panel.
When stationary, with the en-
gine running, do not press the
accelerator pedal unneces-
sarily, as you may release the
parking brake.
Maximum application
If necessary, you can utilise maxi-
mum application
of the parking
brake. It is obtained by means of a
long pull
on control lever A
, until
you see the message "Max applica-
tion of the handbrake" and a beep
is heard.
Maximum application is essential:
- in the case of a vehicle towing
a caravan or a trailer, if the au-
tomatic functions are activated
but you are applying the parking
brake manually,
- when the gradient you are parked
on is variable in its effect (e.g. on
a ferry, in a lorry, during towing).
- in the case of towing, a loaded
vehicle or parking on a gradient,
turn the front wheels towards the
pavement and engage a gear
when you park.
- after a maximum application, the
release time will be longer.
Particular situations
In certain situations (starting the en-
gine...), the parking brake can auto-
matically alter its level of application.
This is normal operation.
To advance your vehicle a few
centimetres without starting the en-
gine, but with the ignition on, press
on the brake pedal and release the
parking brake by pushing
then
releasing
control lever A
.
The full release of the parking brake
is confi rmed by the warning lamp P
in the control lever and the warning
lamp in the instrument panel going
off and the display of a message
"handbrake off" on the instrument
panel screen.
If the parking brake malfunctions
while applied
or if the battery is fl at,
an emergency release is still pos-
sible.
To ensure correct operation of the
parking brake and therefore your
safety, the number of successive
application/release operations is
limited to eight.
If this number is exceeded, you are
warned by the message "Parking
brake faulty" and a warning lamp
fl ashes.
- this warning lamp in the
instrument panel going off,
Page 134 of 340
IX
!
!
132
DRIVING
Dynamic emergency braking
In the event of a failure of the ve-
hicle’s main braking system or in
an exceptional situation (e.g. driver
taken ill, under instruction, etc) pull
and hold control lever A
to stop the
vehicle.
The electronic stability programme
(ESP) provides stability during dy-
namic emergency braking.
If there is a fault with the dynamic
emergency braking, one of the fol-
lowing messages will be displayed
in the instrument panel screen:
- "Parking brake faulty".
- "Parking brake control faulty". If a failure of the ESP system
is signalled by the lighting
of this warning lamp, then
braking stability is not guar-
anteed. In this event, stability must
be assured by the driver by repeat-
ing alternate "pull release" actions on
control lever A
.
The dynamic emergency
braking should only be used
in exceptional circumstances.
Emergency parking brake
release
In the event of the electric parking
brake failing to release, an emergency
device can be used to release the
parking brake manually, provided that
it is possible to immobilise the vehicle
while the procedure is carried out.
)
If you can start the vehicle: with
the engine running, immobilise
the vehicle by applying the foot
brake while the operation is being
carried out.
)
If you are unable to start the
vehicle (fl at battery for example):
do not use this device and contact
a CITROËN dealer or a qualifi ed
workshop. However, if you are
obliged to proceed, fi rst immobilise
your vehicle securely and then fol-
low the instructions below. If the vehicle cannot be im-
mobilised, do not operate
the emergency release. Your ve-
hicle may run away if on a slope.
Contact a CITROËN dealer or a
qualifi ed workshop.
Page 136 of 340
IX
!
134
DRIVING
If any of these instances arises, contact a CITROËN dealer or a qualifi ed workshop as soon as possible.
SITUATION
CONSEQUENCES
1
Electric parking brake fault and display of
message " Parking brake faulty
" and the
following warning lamps: If the electric parking brake fault warning lamp and the service
warning lamp light up, position the vehicle in a safe location (on fl at
ground, with a gear engaged).
2
Display of the messages " Parking brake
faulty
" and " Anti roll-back
fault
" and of the
following warning lamps:
- The automatic functions are deactivated.
- The hill start assist is not available.
- The electric parking brake is only available manually.
3
Display of messages " Parking brake faulty
"
and " Anti roll-back
fault
" and of the following
warning lamp:
- Manual release of the electric parking brake is not available.
- The hill start assist is not available.
- The automatic functions and manual application are still
available.
Operating faults
Page 137 of 340
IX
135
DRIVING
SITUATION
CONSEQUENCES
4
Display of messages " Parking brake faulty
"
and " Anti roll-back
fault
" and of the following
warning lamps:
and/or
fl ashing
- The automatic functions are deactivated.
- The hill start assist is not available.
To apply the electric parking brake:
)
Immobilise the vehicle and switch off the ignition
)
Pull the control lever for at least 5 seconds or until maximum
application.
)
Switch on the ignition and check that the electric parking brake
warning lamps are on.
- Application may take longer than in normal operation.
- If warning lamp (!) fl ashes or if the warning lamps do not come
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer or a qualifi ed workshop.
To release the electric parking brake:
)
Switch on the ignition.
)
Push the control lever and hold it for approximately 3 seconds.
5
Display of message " Parking brake control
faulty – automatic mode activated
" and the
following warning lamps:
and/or fl ashing
- Only the functions for automatic application on switching off the
engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake and dynamic
emergency braking are unavailable.
6
Display of message " Parking brake faulty
"
and of the following warning lamp:
fl ashing
- Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
)
Wait approximately 3 minutes.
)
After 3 minutes, if the warning lamp is still fl ashing, try to
reinitialise the parking brake, either by pushing and releasing
the control A
while pressing the brake pedal or by means of a
long pull on control lever A
.
7
Battery fault
- Illumination of the battery warning lamp makes it essential to stop the
vehicle as soon as traffi c allows. Stop and immobilise your vehicle.
- Apply the electric parking brake before switching off the engine.
Page 142 of 340
IX
140
DRIVING
The position of the gear lever the the
driving mode are displayed in dial C
of the instrument panel.
A selection grille alongside the gear
lever also allows you to see the se-
lected position.
Displays in the instrument panel
Moving off
)
To start the engine, the gear lever
must be in position N
.
)
Press the brake pedal down fully.
)
Operate the starter
N
appears in the instrument panel
screen.
N
fl ashes in the instrument panel,
accompanied by an audible signal
and a message in the multifunction
screen, if the gear lever is not in
position N
on starting.
)
Select fi rst gear (position M
or A
)
or reverse (position R
).
)
Release the parking brake unless
it is programmed in automatic
mode.
)
Release the brake pedal, then
accelerate.
)
With your foot on the brake, push
the lever forwards.
Reverse
Only engage reverse with
the vehicle immobilised.
To avoid any jerking, wait a
moment before accelerating.
Neutral
Never select position N
with
the vehicle moving.
Page 148 of 340
IX
!
146
DRIVING
Mode selection
Displays in the instrument panel
)
automatic mode: gear lever in
position D
,
)
sequential mode: gear lever in
position M
,
)
SPORT
mode: gear lever in po-
sition D
and button A
pressed,
)
SNOW
mode: gear lever in posi-
tion D
and button B
pressed.
The position of the gear lever and
the driving mode are displayed in
the instrument panel dial C
.
A position grille associated with the
gear lever allows you to view the se-
lected position.
For safety:
- position P
can be disen-
gaged only if you press
the brake pedal,
- when a door is opened, an au-
dible signal is heard if the gear
lever is not in position P
,
- always make sure that the gear
lever is in position P
before you
leave your vehicle.
If the gearbox is in position P
but
the position of the gear lever is dif-
ferent, reposition the gear lever
on P
so that you can start the ve-
hicle.
AUTOMATIC GEARBOX
Automatic gearbox which offers a
choice between the comfort of fully
automatic operation, enhanced by
the sport and snow programmes, or
manual gear changing.
Four driving modes are provided:
- automatic
operation for elec-
tronic control of the gears by the
gearbox,
- the SPORT
programme for a
more dynamic driving style,
- the SNOW
programme to improve
driving when the grip is poor,
- manual
operation for sequential
changing of the gears by the driver.
Page 152 of 340
IX
150
DRIVING
FIXED CENTRED CONTROLS STEERING WHEEL
1
Rotation
-
Scroll the various pages of information on the instrument panel screen.
- Move through the various menus on the instrument panel screen.
- Increase/decrease values.
Short press
-
Open the menu on the instrument panel screen (only when stationary).
- Select and confi rm information.
Long press Trip computer zero reset (if the trip computer page is displayed).
2
Short press
- Cancel the current operation.
-
Return to the previous screen on the instrument panel screen.
Long press Return to the initial page on the instrument panel screen.
3
Short press Increase the speed in steps of 1 mph (1 km/h)/storing the speed.
Maintained press Increase the speed in steps of 5 mph (5 km/h).
4
Short press
Decrease the speed in steps of 1 mph (1 km/h)/storing the speed.
Maintained press Decrease the speed in steps of 5 mph (5 km/h).
5
Short press Suspend or resume cruise control/speed limiter (depending
on the mode selected).
6
Short press Select cruise control or speed limiter mode (the cycle on this
button will always begin with selection of the speed limiter).
7
Short press Deactivate cruise control/speed limiter.
8
Short press
- Pick up an incoming call.
- Hang up the current call.
- Open the telephone short-cut menu.
- Confi rm on the list and the telephone menu.
Long press Refuse an incoming call.
9
Short press/Long press Horn.
10
Short press Activate/deactivate Black Panel mode (night driving).
11
Short press Activate the voice command.
Long press Navigation instruction repeat.