engine oil CITROEN C6 2005 Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 89
INJECTION
BOSCH ME 7.4.7 INJECTION SYSTEM
Engine: ES9AIgnition circuit
Component Location Supplier Reference Observations
BOSCH FGR8MQPEElectrode gap: 1 mm
Sparking plugs 31Tightening torque
NGK PFR6E 10Tighten to: 1 ± 0,1 m.daN
Angular tightening: 90°
Pencil type ignition 17 SAGEM BAC 14-way blackconnector
coils 2526140 Twin-static type ignition
Exhaust circuit
4-way greenconnector
Upstream oxygen sensor 21 258 040 232 Front fixing: on the exhaust manifold
Rear fixing: on the pre-catalyser
BOSCH4-way blueconnector
Front fixing: on the pre-catalyser
Downstream oxygen sensor 20 258 006 185 Rear fixing: on the pre-catalyser
Tightening torque
Tighten to: 4,7 ± 0,1 m.daN
Angl-C6-page83-100-2005 4/02/05 17:22 Page 89

Downloaded from www.Manualslib.com manuals search engine 103
CLUTCH
GEARBOX
TRANSMISSION
PROCEDURE PRIOR TO OPERATIONS: AM6 AUTOMATIC GEARBOX
If a gearbox malfunction occurs, there are two possible configurations
depending on the seriousness of the fault:
- Gearbox in back-up mode with a replacement programme of (the fault
values are taken in substitution).
- Gearbox in back-up mode with an emergency programme (3rd hydraulic).
WARNING: In the emergency programme, an impact is felt when
changing P/R or N/R.
Reception of the customer.
Discuss with the customer, to find out all the malfunction symptoms.
Oil quality.
If the gearbox has suffered a serious fault resulting in a malfunction or
the destruction of a clutch, the oil will overheat and become
contaminated with impurities: the oil is said to be «burnt».
This is characterised by a black colour and the presence of an
unpleasant smell.
ESSENTIAL: The gearbox must be replaced.Oil level.
Preliminary conditions:
- Vehicle horizontal, parking brake off.
- Check that the gearbox is not in back-up mode (using a diagnostic tool).
- The oil temperature should be 60°C (+8, -2)(using a diagnostic tool).
- Press on the brake pedal, change through all the gears.
- Place the gear lever in position P.
With the engine running at idle, without power consumers (aircon,
heating, etc.):
- Remove the oil level plug.
The oil should flow out, then drip-drip.
Refit the oil level plug (the oil level is correct).
The oil does not flow out through the oil level plug (see operation: drain
fill - bleed the gearbox).
Engines: ES9A - DT17BTED4
Angl-C6-page101-120-2005 4/02/05 17:25 Page 103

Downloaded from www.Manualslib.com manuals search engine 104
CLUTCH
GEARBOX
TRANSMISSION
PRECAUTIONS TO BE TAKEN : AM6 AUTOMATIC GEARBOX
Towing.
The front of the vehicle must be raised in order to be towed.
If the front of the vehicle cannot be raised.
IMPERATIVE:
- Put gear lever in position «N».
- Do not add any oil.
- Do not exceed 70 km/h (45 mph)over a distance of 100 km (60 miles)
maximum.
Driving.
Never drive with the ignition switched off.
NOTE:The automatic gearbox is only lubricated when the engine is
running.
Repairs on electrical components.
Do not disconnect:
- The battery when the engine is running.
- The ECU when the ignition is switched on.
Before reconnecting a switch, check:
- The condition of the various contacts (for deformation, corrosion etc.)
- The presence and condition of the mechanical locking.When performing electrical checks:
- The battery should be correctly charged.
- Never use a voltage source higher than 16V.
- Never use a test lamp.
Repairs on mechanical components.
Never place the gearbox on the ground without protection.
Do not use the unions on the gearbox as handles for moving the
gearbox.
It is imperative
that the converter retaining peg should be in place
when removing the gearbox.
It is imperativeto use the centring pegs to couple the gearbox on the
engine.
Remove the converter retaining peg before coupling the gearbox on
the engine.
Engines: ES9A - DT17BTED4Precautions to be taken
Angl-C6-page101-120-2005 4/02/05 17:25 Page 104

Downloaded from www.Manualslib.com manuals search engine 107
CLUTCH
GEARBOX
TRANSMISSION
Engines: ES9A - DT17BTED4
12 Oil induction cover 1 ± 0,111 Hydraulic valve block (in the order indicated) 1 ± 0,112 Oil temperature sensor tightening plate 1 ± 0,113 ECU screws 2,5 ± 0,214 Oil drain and overflow plug 1 ± 0,115 Oil level plug 4,8 ± 0,5
B2CP42ZD
AM6 GEARBOX: TIGHTENING TORQUES
B2CP42YD
Angl-C6-page101-120-2005 4/02/05 17:25 Page 107

Downloaded from www.Manualslib.com manuals search engine 112
CLUTCH
GEARBOX
TRANSMISSION
PROCEDURE FOR INITIALISATION OF THE AUTOMATIC GEARBOX ECU
NOTE:For all these operations, follow the procedure in the diagnostic tool.
Replacement of the automatic gearbox without replacement of the ECU.
Carry out the following operations:
- Initialisation of the neutral position of the gear selection lever position sensor.
- Initialisation of the adaptation of the oil pressure regulators and electrovalves.
- Initialisation of the autoadaptatives.
- Resetting the oil usage counter to zero.
Replacement of the automatic gearbox ECU.
Carry out the following operations:
- Read the value of the gearbox oil usage counter from the old ECU.
- Write the value of the oil usage counter into the new ECU.
- Initialisation of the neutral position of the gear selection lever position sensor.
- Initialisation of the adaptation of the oil pressure regulators and electrovalves.
- Initialisation of the autoadaptatives.
Angl-C6-page101-120-2005 4/02/05 17:25 Page 112

Downloaded from www.Manualslib.com manuals search engine 113
CLUTCH
GEARBOX
TRANSMISSION
PROCEDURE FOR INITIALISATION OF THE AUTOMATIC GEARBOX ECU
Replacement of the automatic gearbox and of the automatic gearbox ECU.
Carry out the following operations:
- Initialisation of the autoadaptatives.
- Resetting the oil usage counter to zero.
- Initialisation of the adaptation of the oil pressure regulators and electrovalves.
Draining of the automatic gearbox oil.
Carry out the following operations:
- Initialisation of the adaptation of the oil pressure regulators and electrovalves.
- Resetting the oil usage counter to zero.
NOTE:If downloading the automatic gearbox ECU, there is no specific operation, follow the procedure in the diagnostic tool.
IMPERATIVE: For a certain time, having carried out an ECU initialisation procedure, one may obtain gear changing quality that is more
or less good (adaptation of the ECU parameters to the gearbox). To improve the quality, it is necessary to perform a road test with
frequent changing through the gears (auto-adaptive laws).
Angl-C6-page101-120-2005 4/02/05 17:25 Page 113

Downloaded from www.Manualslib.com manuals search engine 114
CLUTCH
GEARBOX
TRANSMISSION
DRAINING, FILLING AND TOPPING UP THE AM6 AUTOMATIC GEARBOX
Tool.
[1] Filling cylinder: (-).0340
Respect the safety and cleanliness requirements.
Draining.
IMPERATIVE: Draining of the gearbox must be done with the oil hot (60°C minimum), in order to
ensure that the impurities in suspension in the oil are eliminated.
NOTE:Drainage is only partial, as the torque converter cannot be drained totally.
Raise the vehicle.
Remove:
- The oil level plug (2)by means of the Torx spanner.
- The drain plug (1)using a hexagonalspanner.
NOTE :Around 3 litresof oil should flow out.
Filling.
Fit the drain plug (1)(with a new seal).
Tighten the plug (1)to: 5 ± 1 mdaN.
Remove:
- The air filter housing.
- The oil filler plug (3).
Use tool [1].
B2CP3WZCB1BP317C
Angl-C6-page101-120-2005 4/02/05 17:25 Page 114

Downloaded from www.Manualslib.com manuals search engine 115
CLUTCH
GEARBOX
TRANSMISSION
DRAINING, FILLING AND TOPPING UP THE AM6 AUTOMATIC GEARBOX
WARNING: Do not take account of the information mentioned on tool [1].
Oil capacity for a dry gearbox: 7 litres (approx.).
Type of oil: JWS 3309 ESSO(red in colour).
Volume of oil remaining after draining: 4 litres (approx.).
Quantity of oil to be added: 3 litres (approx.).
Refit the filler plug (3)(with a new seal).
Tighten the plug (3)to: 4 ± 1 mdaN.
Initialise the oil usage counter (follow the procedure in the diagnostic tool).
Checking the oil level.
Prior conditions:
- Vehicle in a horizontal position.
- Check that the gearbox is not in back-up mode.
Remove the filler plug (3).
Add 0.5 litreof extra oil into the gearbox.
Press the brake, change through all the gears.
Gear lever in position "P".
Engine running, at idle:
- Oil temperature 60°C (+ 8 ; - 2)(parameter measures with a diagnostic tool).
- Remove the level plug (2).
B2CP3WZCB1BP317C
Angl-C6-page101-120-2005 4/02/05 17:25 Page 115

Downloaded from www.Manualslib.com manuals search engine 116
CLUTCH
GEARBOX
TRANSMISSION
DRAINING, FILLING AND TOPPING UP THE AM6 AUTOMATIC GEARBOX
Thread of oil, then "drip-drip".
Refit the level plug (2).
Tighten the plug (2)to: 0.8 ± 0,1 mdaN.
"drip-drip" or nothing.
Refit the level plug (2).
Stop the engine.
Add 0.5 litreof extra oil into the gearbox.
Repeat the topping-up procedure.
NOTE:The level is correct when the thread of oil becomes "drip-drip".
Refit the level plug (2)(with a new seal).
Tighten the plug (2)to: 0.8 ± 0,1 mdaN.
Refit the filler plug (3)(with a new seal).
Tighten the plug (3)to: 4 ± 1 mdaN.
A level of oil that is too high can have the following consequences: Abnormal overheating of the oil, leaks of oil
causing a level which is too low resulting in destruction of the gearbox.
B2CP3WZCB1BP317C
Angl-C6-page101-120-2005 4/02/05 17:25 Page 116

Downloaded from www.Manualslib.com manuals search engine 117
CLUTCH
GEARBOX
TRANSMISSION
CHECKING THE OIL PRESSURE IN THE AM6 AUTOMATIC GEARBOX
Tools.
[1]Flexible pipe and pressure gauge: 4601- TF1 Toolkit 4601-T
[2]Flexible union: (-).0336.X Toolkit 8010-T
IMPERATIVE: Respect the safety and cleanliness requirements.
Preliminary operations.
Remove the air filter housing.
Move aside the pipe (1).
Remove the screw (2).
Screw in the tool [2]in place of the screw (2).
B2CP45GCB2CP45FC
Angl-C6-page101-120-2005 4/02/05 17:25 Page 117