torque CITROEN C6 2005 Owner's Guide

Downloaded from www.Manualslib.com manuals search engine 114
CLUTCH
GEARBOX
TRANSMISSION
DRAINING, FILLING AND TOPPING UP THE AM6 AUTOMATIC GEARBOX
Tool.
[1] Filling cylinder: (-).0340
Respect the safety and cleanliness requirements.
Draining.
IMPERATIVE: Draining of the gearbox must be done with the oil hot (60°C minimum), in order to
ensure that the impurities in suspension in the oil are eliminated.
NOTE:Drainage is only partial, as the torque converter cannot be drained totally.
Raise the vehicle.
Remove:
- The oil level plug (2)by means of the Torx spanner.
- The drain plug (1)using a hexagonalspanner.
NOTE :Around 3 litresof oil should flow out.
Filling.
Fit the drain plug (1)(with a new seal).
Tighten the plug (1)to: 5 ± 1 mdaN.
Remove:
- The air filter housing.
- The oil filler plug (3).
Use tool [1].
B2CP3WZCB1BP317C
Angl-C6-page101-120-2005 4/02/05 17:25 Page 114

Downloaded from www.Manualslib.com manuals search engine 119
CLUTCH
GEARBOX
TRANSMISSION
CHECKING THE OIL PRESSURE IN THE AM6 AUTOMATIC GEARBOX
Checking the torque converter.
WARNING: This check has to be of short duration (2 seconds), as it causes a rapid
rise in the temperature of the oil in the automatic gearbox.
Respect the following checking conditions:
- Engine at operating temperature.
- Gear lever in position D.
- Press on the brake pedal.
- Accelerate the engine to the maximum engine speed (see below).
Gear lever position.: D.
Maximum engine speed for ES9A : 2400 ± 50 rpm.
Maximum engine speed for DT17 : 2600 ± 50 rpm.
Diagnosis:
- If the maximum engine speed obtained is lower than the value indicated, the torque
converter is the cause.
- If the maximum engine speed obtained is higher than the value indicated, the automatic
gearbox is the cause (slipping).
Additional operations.
Remove tools [1]and [2].
Refit the screw (2), with a new seal.
Reposition the pipe (1).
Refit the air filter housing.
B1BP3END
Angl-C6-page101-120-2005 4/02/05 17:25 Page 119

Downloaded from www.Manualslib.com manuals search engine 120
CLUTCH
GEARBOX
TRANSMISSION
TRANSMISSION
Tightening torques (m.daN)Gearbox oil seal mandrels
Vehicle GearboxDriveshaft Driveshaft
Engines
bearing nutRight Left Tool kit
(-).0336.U (-).0336.V
C6 AM6 ES9A - DT17BTED4 2 ± 0,2 34,5 ± 2 8010-T
(-).0336.W (1)
(1) Guide for fitting driveshaft seal.
Tightening torques (m.daN) of the wheel bolts
CITROËNES9Al Steel
DT17BTED4 Alloy9 ± 1
Angl-C6-page101-120-2005 4/02/05 17:25 Page 120

Downloaded from www.Manualslib.com manuals search engine 123
AXLES
SUSPENSION
STEERING
WHEEL AND TYRES(1)Wheel bolt (all rim types)
(2)Light alloy wheel
(3)Steel aluminium wheel
NOTE:If mixed fixing bolts are fitted on steel wheels, the shoulders of the bolts
remain free.
Tightening torques for the wheel bolts.
9 ± 1 m.daN
B2GP00JD
Identification of the wheel bolts
Angl-C6-page121-169-2005 4/02/05 17:31 Page 123

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
136
FRONT AXLE: TIGHTENING TORQUES
Engines: ES9A - DT17BTED4
Suspension leg
1 Body suspension upper support 2,6 ± 0,32 Front suspension cylinder on Suspension upper support 2,4 ± 0,33 Suspension upper arm on Suspension upper support 4,5 ± 0,64 Suspension upper arm on Pivot support 8,5 ± 0,85 Front anti-roll bar rod on Pivot support 20,5 ± 26 Pivot upper balljoint on Pivot support 15 ± 1,57 Pivot upper balljoint nut 6 ± 0,68 Front anti-roll bar rod on Front anti-roll bar 5 ± 0,59 Suspension lower arm on Pivot support 7,5 ± 1,1
B3CP09ECB3CP09DC
Angl-C6-page121-169-2005 4/02/05 17:31 Page 136

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
137
FRONT AXLE: TIGHTENING TORQUES
Engines: ES9A - DT17BTED4
Suspension leg
10 Pivot lower balljoint on Pivot support 6,5 ± 0,911 Pivot lower balljoint on Pivot support 17 ± 1,712 Steering rack balljoint on Front pivot 3,5 ± 0,3
B3CP09FC
Angl-C6-page121-169-2005 4/02/05 17:31 Page 137

Downloaded from www.Manualslib.com manuals search engine 138
AXLES
SUSPENSION
STEERING
FRONT AXLE: TIGHTENING TORQUES
Engines: ES9A - DT17BTED4
Front subframe
13 Front subframe frame tie-bar on Body 5 ± 0,714 Front subframe frame tie-bar on Front subframe frame 6,5 ± 0,915 Front absorber support tie-bar 6,5 ± 0,916 Front subframe frame on Subframe extension 10 ± 117 Front subframe frame crossmember 10 ± 118 Subframe extension on Front subframe 5,5 ± 0,519 Front subframe stabiliser bar 12,5 ± 1,220 Front subframe on Body 14 ± 1,421 Suspension lower arm on Front subframe 6,5 ± 0,622 Suspension lower arm on Front subframe 11 ± 1,123 Front anti-roll bar bearing on Front subframe 4,5 ± 0,624 Body yoke 10 ± 1
B3CP09HDB3CP09GD
Angl-C6-page121-169-2005 4/02/05 17:31 Page 138

Downloaded from www.Manualslib.com manuals search engine 139
AXLES
SUSPENSION
STEERING
FRONT AXLE: TIGHTENING TORQUES
Engines: ES9A - DT17BTED4
Front subframe
25 Suspension lower arm support on Front subframe 6,5 ± 0,926 Suspension lower arm on Front subframe 12,3 ± 1,2
B3CP09TC
Angl-C6-page121-169-2005 4/02/05 17:31 Page 139

Downloaded from www.Manualslib.com manuals search engine 142
AXLES
SUSPENSION
STEERING
REAR AXLE: TIGHTENING TORQUES
Engines: ES9A - DT17BTED4
1 Rear axle crossmember on Body 7,5 ± 0,7
2 Rear anti-roll bar bearing on Body
3 Tracking adjustment rod on Rear pivot
4 Rear suspension cylinder on Rear pivot
5 Suspension longitudinal arm on Rear pivot 7 ± 0,7
6 Suspension lower arm on Rear pivot
7 Suspension lower arm on Rear axle crossmember8 Tracking adjustment rod on Rear axle crossmember9 Locking of tracking adjustment rod 1 ± 0,2
Suspension longitudinal arm on Body
10Pre-tightening3,3 ± 0,3
Angular tightening 150° ± 5°
B3DP0BVDB3DP0BUD
Angl-C6-page121-169-2005 4/02/05 17:31 Page 142

Downloaded from www.Manualslib.com manuals search engine 143
AXLES
SUSPENSION
STEERING
REAR AXLE: TIGHTENING TORQUES
Engines: ES9A - DT17BTED4
11 Suspension upper arm on Rear pivot
12 Suspension upper arm on Rear axle crossmember 7 ± 0,7
13 Rear suspension cylinder on Rear axle crossmember
14 Rear anti-roll bar rod on Rear pivot
4 ± 0,615 Rear anti-roll bar rod on Rear anti-roll bar16 Rear anti-roll bar bearing half support 1,8 ± 0,417 Rear hub-bearing nut 25 ± 2
B3DP0BXDB3DP0BWD
Angl-C6-page121-169-2005 4/02/05 17:31 Page 143