battery CITROEN C6 2005 Owners Manual

Downloaded from www.Manualslib.com manuals search engine GENERAL
Vehicle identification1 - 4
General specifications: dimensions 5 - 6
General specifications: weights7
Operations to be performed before and
after a disconnection of the battery8
Towing specifications9 - 10
Lifting and supporting the vehicle11 - 15
Capacities18
Lubricants18 - 20
ENGINE
Engine specifications22
Engine suspension tightening torques: ES9A23
Tightening torques: ES9A engine24 - 28
Suspension tightening torques: DT1729 - 31
Adjustment of torque reaction rod32
Tightening torques: DT17 engines33 - 41
Cylinder head tightening42 - 43IGNITION
Sparking plugs100
CLUTCH - GEARBOX - TRANSMISSION
Speedometer101
AM6 automatic gearbox specifications
102
Procedure before operations103
Precautions: AM6 gearbox104
AM6 gearbox specifications105
Tightening torques: AM6 gearbox106 - 107
AM6 gearbox control specifications 108 - 110
Shift lock function111
Initialisation of the AM6 gearbox112 - 113
Draining-filling-topping up
the AM6 gearbox114 - 116
Oil pressure checks: AM6 gearbox117 - 119
Transmission120
CONTENTS
Auxiliary equipment drive belt45
Checking and setting the valve timing50
Exhaust line specifications68 - 72
Cooling system specifications73 - 75
Checking the oil pressure76
Valve clearances77
Drain-fill-bleed the engine cooling circuit78 - 82
INJECTION
BOSCH 7.4.7 injection system83 - 89
Prohibited operations: SIEMENS HDi
direct injection90 - 91
Safety requirements: HDi direct injection92
Checking the low pressure fuel
supply circuit 93 - 94
Turbo pressure checks95 - 97
Air supply circuit specifications98
Checking the air supply circuit99
Angl-C6-Index-2005 4/02/05 17:10 Page III

Downloaded from www.Manualslib.com manuals search engine 8
GENERAL
OPERATIONS TO BE CARRIED OUT BEFORE AND AFTER A DISCONNECTION OF THE BATTERY
Before reconnecting the battery
.
Doors and tailgate.
WARNING: Before disconnecting the battery, partially open the door
windows.
Automatic gearbox.
If the vehicle has to remain stationary: Pplace the gear lever in the parking
position "P".
If the vehicle has to be moved: Place the gear lever in the neutral position
"N".
Electric parking brake.
If the vehicle has to remain stationary: Activate the electric parking brake.
If the vehicle has to be moved: Deactivate the electric parking brake.
Features of the vehicle's electrical supply.
When the boot is closed and the battery is disconnected, it is possible to
supply the vehicle by connecting another battery or a 12Vexterior supply.
Operations to be performed:
- Link the earth of the exterior supply to the vehicle earth.
- Link the 12Vof the exterior supply to the positive terminal of the battery +
unit, in the front left hand side of the engine compartment.
After reconnecting the battery
.
Antiscanning function.
It is necessary to wait 1 minuteafter reconnecting the battery in order to be
able to restart the vehicle.
Electric windows.
It may be necessary to re-initialise the sequential and anti-pinch functions.NOTE:If the window is open at the time the battery is reconnected, action
the window switch several times to close it, then re-initialise.
Open the window fully.
Action and release the window switch until the window is completely closed.
NOTE:This operation has to be carried out on each electric window.
Sun roof.
The anti-pinch function has to be re-initialised.
Place the sun roof switch in the maximum tilt position.
Keep the sun roof switch pressed until the sun roof ceases its movement.
Release the sun roof switch.
Press the sun roof switch within 5 seconds.
Keep the sun roof switch pressed until the end of the sun roof opening
sequence.
Multifunction screen.
It is necessary to adjust the date, time and outside temperature.
Adjust the display language of the multifunction screen if necessary.
NOTE:The default display language of the multifunction screen is French.
Reconfigure the personalisation menu of the multifunction screen.
Radio.
Reprogramme the radio stations.
Telematic control unit (RT3 radiotelephone).
Reprogramme the radio stations.
Navigation.
Warning: the vehicle has to be out in the open (when you switch on
the ignition, the navigation ECU searches for satellites).
Reprogramme the customer parameters.
Angl-C6-page001-21-2005 4/02/05 17:12 Page 8

Downloaded from www.Manualslib.com manuals search engine 58
ENGINE
CHECKING THE VALVE TIMING
Engine: DT17BTED4
Tools.
[1]Set of plugs: (-).0188-T
[2]Flywheel setting peg (double flywheel): (-).0195.K Toolkit 0188-T
[3]Camshaft setting pegs: (-).0195.H Toolkit 0188-T
Checks.
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure
Diesel injection (HDi) engines.
Remove the engine cover.
Disconnect the battery negative terminal.
Raise and support the front of the vehicle.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The front RH splash-shield (see corresponding operation).
Remove:
- The air duct between the air/air exchanger and the air inlet housing (4).
- The air inlet housing (4).
Uncouple, plug and move aside the pipes (2)and (3), using tools [1].
Unclip and move aside the electrical harness.
Remove the venting chamber fixing (1).
Move aside the venting chamber (1).
B1BP3BXD
Angl-C6-page022-82-2005 4/02/05 17:19 Page 58

Downloaded from www.Manualslib.com manuals search engine 61
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: DT17BTED4
Tools.
[1] Kit of plugs: (-).0188-T
[2]Flywheel setting peg (double damping flywheel): (-).0195.K Toolkit 0188-T
[3]Camshaft setting pegs: (-).0195.H Toolkit 0188-T
[4]Belt compressure spring: (-).0188.K
[5]Coolant pump pulley peg: (-).0195.C
[6]Lifting bracket: (-).0195.N
IMPERATIVE: Respect the safety and cleanliness requirements.
WARNING: Before disconnectng the battery, partially open the door windows.
Removing.
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel injection (HDi) engines.
Remove the engine cover.
Disconnect the negative terminal of the battery.
Raise and support the front of the vehicle.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The front RH splash-shield (see corresponding operation).
Angl-C6-page022-82-2005 4/02/05 17:19 Page 61

Downloaded from www.Manualslib.com manuals search engine 83
INJECTION
BOSCH ME 7.4.7 INJECTION SYSTEM
Engine: ES9A
Synopsis.
(1) Fuel consumption information
(2)Ignition injection test warning lamp
(3)Rev counter
(4)Air conditioning ECU
(5)Multifunction screen
(6)Built-in systems interface
(7)Transponder
(8)Automatic gearbox ECU
(9)Fuel pump, filter and pressure regulator (except grande exportation)
(10)Battery
(11)Pressostat
(12)Engine speed sensor
(13)Camshaft position sensor (x2)
(14)Motorised butterfly housing
B1HP1Z9P
Angl-C6-page83-100-2005 4/02/05 17:22 Page 83

Downloaded from www.Manualslib.com manuals search engine 104
CLUTCH
GEARBOX
TRANSMISSION
PRECAUTIONS TO BE TAKEN : AM6 AUTOMATIC GEARBOX
Towing.
The front of the vehicle must be raised in order to be towed.
If the front of the vehicle cannot be raised.
IMPERATIVE:
- Put gear lever in position «N».
- Do not add any oil.
- Do not exceed 70 km/h (45 mph)over a distance of 100 km (60 miles)
maximum.
Driving.
Never drive with the ignition switched off.
NOTE:The automatic gearbox is only lubricated when the engine is
running.
Repairs on electrical components.
Do not disconnect:
- The battery when the engine is running.
- The ECU when the ignition is switched on.
Before reconnecting a switch, check:
- The condition of the various contacts (for deformation, corrosion etc.)
- The presence and condition of the mechanical locking.When performing electrical checks:
- The battery should be correctly charged.
- Never use a voltage source higher than 16V.
- Never use a test lamp.
Repairs on mechanical components.
Never place the gearbox on the ground without protection.
Do not use the unions on the gearbox as handles for moving the
gearbox.
It is imperative
that the converter retaining peg should be in place
when removing the gearbox.
It is imperativeto use the centring pegs to couple the gearbox on the
engine.
Remove the converter retaining peg before coupling the gearbox on
the engine.
Engines: ES9A - DT17BTED4Precautions to be taken
Angl-C6-page101-120-2005 4/02/05 17:25 Page 104

Downloaded from www.Manualslib.com manuals search engine 111
CLUTCH
GEARBOX
TRANSMISSION
AM6 GEARBOX CONTROLS: «SHIFT LOCK» FUNCTIONIMPERATIVE: Respect the safety and cleanliness requirements, with reference to the brochure:
«Recommendations-Precautions».
The «shift lock»is a system that locks the gear selection lever in position «P».
Unlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed.
Move the gear selection lever out of position «P».
Unlocking the «SHIFT LOCK» (with an operating fault).
Should it be impossible to unlock the «shift lock»with the «Normal operation»method.
The fault may originate from one of the following components:
- «Shift lock».
- Gear lever position switch.
- Automatic gearbox ECU.
- Electrical harness.
- Battery voltage.
Operations to be performed.
Unclip the cover (1).
Unlock the «shift lock»by pressing at "a"with the aid of a screwdriver (screwdriver with a minimum length of
150 mm).
Move the gear selection lever out of position "P".
C5FP0RCD
Engines: ES9A - DT17BTED4
C5FP0RBC
Angl-C6-page101-120-2005 4/02/05 17:25 Page 111

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
124
WHEEL AND TYRES(4)Valve(8)Seal
(5)Antenna(9)Cap
(6)HF transmitter unit(10)Nut
(7)Washer
Composition.
A SIEMENS HFtransmitter module (6) integral to each wheel in the place of the
valve, each including a lithium battery.
An HFreceiver in the communication module under the dashboard.
WARNING: Each time a tyre is replaced, it is necessary to replace the valve (4).
WARNING: Each time a wheel rim is replaced, it is necessary to replace the
seal (8).
WARNING: Each time a transmitter module is changed, it is necessary to have
the replacement recognised by the deflation detection ECU, using a diagnostic
tool.
B2GP01ND
Deflation detection system
Angl-C6-page121-169-2005 4/02/05 17:31 Page 124

Downloaded from www.Manualslib.com manuals search engine 182
BRAKES
GENERAL FEATURES OF ELECTRIC PARKING BRAKE
Releasing of the electric parking brake (with a fault).
NOTE:Impossible to release the parking brake with the method "Normal functioning".
The fault may be caused by the following components:
- Battery voltage.
- Malfunctioning of the electric parking brake system.
Open the central armrest.
Pull on the handle (7)located on the plastic part of the central armrest in order to release the parking
brake mechanically.
WARNING: This control does not permit application of the parking brake.
WARNING: It is forbidden to open up the electric parking brake system.
C5FP0W4D
Angl-C6-PAGE170-194-2005 4/02/05 17:35 Page 182

Downloaded from www.Manualslib.com manuals search engine 183
BRAKES
ELECTRIC PARKING BRAKE SYSTEMRemoving-refitting the electric parking brake system.
IMPERATIVE: Respect the safety and cleanliness requirements.
WARNING: Before disconnecting the battery, partially open the door windows.
Removing.
IMPERATIVE: Disconnect the battery prior to operating on the parking brake cables.
IMPERATIVE: Perform a manual unlocking of the parking brake, using the handle located in
the central armrest, before operating on the parking brake cables.
Disconnect the battery.
Raise and support the vehicle, wheels hanging.
Remove the central console (1)(see corresponding operation).
Uncouple the handle (2)from the manual unlocking cable of the electric parking brake.
Remove:
- The exhaust line (4) (ES9A engine).
- The protection (5).
- The protection (3).
C5FP0VVDB1JP08XD
Angl-C6-PAGE170-194-2005 4/02/05 17:35 Page 183