brake CITROEN C6 2005 Owners Manual

Downloaded from www.Manualslib.com manuals search engine PRESENTATION
THIS HANDBOOK summarises the specifications, adjustments, checks and special features of CITROËNprivate vehicles, not including UTILITY vehicles for which there exists a
separate handbook.
The handbook is divided into groups representing the main functions:
GENERAL - ENGINE - INJECTION - IGNITION - CLUTCH, GEARBOX, DRIVESHAFTS - AXLES, SUSPENSION, STEERING - BRAKES - HYDRAULICS - AIR CONDITIONING.
Angl-C6-Index-2005 4/02/05 17:10 Page I

Downloaded from www.Manualslib.com manuals search engine AXLES - SUSPENSION - STEERING
Wheels and tyres121 - 124
Checking and adjusting the vehicle height125 - 128
Values for checking and adjusting
the axle geometries129 - 133
Front axle134 - 135
Front axle tightening torques136 - 139
Rear axle140 - 141
Rear axle tightening torques142 - 143
Active suspension with variable damping144 - 149
Suspension tightening torques150 - 154
Draining-filling-bleeding
the hydraulic steering/suspension circuit155 - 158
Power steering specifications159 - 162
Power steering tightening torques163 - 164
Checking the steering assistance
pressure (ES9A engine)165 - 168
Bleeding the hydraulic steering
assistance circuit169AIR CONDITIONING
Quantities: aircon system R134.a 203
Special features: air conditioning circuit 204 - 205
Pollen filter206
Checking the compressor oil level207 - 208
Checking the efficiency of
the air conditioning circuit209 - 215
Air conditioning circuit: ES9A216
Air conditioning circuit: DT17217
CONTENTS
BRAKES
Brake specifications170
Braking system: general specifications171 - 173
Braking system: tightening torques174 - 177
Values for checking and adjusting
the braking system178
General feataures of
the electric parking brake179 - 189
Brake fluid checks190
Drain-fill-bleed the braking system191 - 194
HYDRAULICS
Safety requirements:
active suspension with variable damping195 - 197
Suspension spheres: general specifications 198
Suspension spheres:
specification - identification199 - 200
Depressurising the hydraulic
suspension circuit201 - 202
Angl-C6-Index-2005 4/02/05 17:10 Page IV

Downloaded from www.Manualslib.com manuals search engine 7
GENERAL
GENERAL SPECIFICATION: WEIGHTS
ES9A DT17BTED4
Versions 3.0i 24S 2.7HDi 24VEngine type XFV UHZGearbox typeAM6Payload 455 464Weight empty in running order 1816 1871Gross Vehicle weight 2271 2335Gross Train weight3671Max. trailer weight with brakes
Incline 12 % 1400
Incline 10 % 1500 1400Incline 8 % 1700Max. trailer weight without brakes 750Maximum nose weight70Maximum weight on roof bars 80
NOTE: Maximum nose weight = Vertical load at the tow hook (CVA).
Angl-C6-page001-21-2005 4/02/05 17:12 Page 7

Downloaded from www.Manualslib.com manuals search engine 8
GENERAL
OPERATIONS TO BE CARRIED OUT BEFORE AND AFTER A DISCONNECTION OF THE BATTERY
Before reconnecting the battery
.
Doors and tailgate.
WARNING: Before disconnecting the battery, partially open the door
windows.
Automatic gearbox.
If the vehicle has to remain stationary: Pplace the gear lever in the parking
position "P".
If the vehicle has to be moved: Place the gear lever in the neutral position
"N".
Electric parking brake.
If the vehicle has to remain stationary: Activate the electric parking brake.
If the vehicle has to be moved: Deactivate the electric parking brake.
Features of the vehicle's electrical supply.
When the boot is closed and the battery is disconnected, it is possible to
supply the vehicle by connecting another battery or a 12Vexterior supply.
Operations to be performed:
- Link the earth of the exterior supply to the vehicle earth.
- Link the 12Vof the exterior supply to the positive terminal of the battery +
unit, in the front left hand side of the engine compartment.
After reconnecting the battery
.
Antiscanning function.
It is necessary to wait 1 minuteafter reconnecting the battery in order to be
able to restart the vehicle.
Electric windows.
It may be necessary to re-initialise the sequential and anti-pinch functions.NOTE:If the window is open at the time the battery is reconnected, action
the window switch several times to close it, then re-initialise.
Open the window fully.
Action and release the window switch until the window is completely closed.
NOTE:This operation has to be carried out on each electric window.
Sun roof.
The anti-pinch function has to be re-initialised.
Place the sun roof switch in the maximum tilt position.
Keep the sun roof switch pressed until the sun roof ceases its movement.
Release the sun roof switch.
Press the sun roof switch within 5 seconds.
Keep the sun roof switch pressed until the end of the sun roof opening
sequence.
Multifunction screen.
It is necessary to adjust the date, time and outside temperature.
Adjust the display language of the multifunction screen if necessary.
NOTE:The default display language of the multifunction screen is French.
Reconfigure the personalisation menu of the multifunction screen.
Radio.
Reprogramme the radio stations.
Telematic control unit (RT3 radiotelephone).
Reprogramme the radio stations.
Navigation.
Warning: the vehicle has to be out in the open (when you switch on
the ignition, the navigation ECU searches for satellites).
Reprogramme the customer parameters.
Angl-C6-page001-21-2005 4/02/05 17:12 Page 8

Downloaded from www.Manualslib.com manuals search engine 10
GENERAL
GENERAL SPECIFICATION: TOWING THE VEHICLE
Vehicle with automatic gearbox.
IMPERATIVE: Never tow the vehicle with the wheels hanging (towing by the wheels).
Towing:
- It is necessary to raise the front of the vehicle, in order to tow it.
- If it is not possible to raise the front of the vehicle.
- It is essential to place the selection lever in position "N".
- Do not add any oil.
- Do not exceed a speed of 70 km/h(45 mph)on a journey of 100 Km (60 miles).
- Never tow the vehicle backwards.
- Check that the parking brake is released.
Driving:
- Never drive with the ignition switched off.
NOTE: The automatic gearbox is only lubricated when the engine is running.
Never push the vehicle to attempt to start it (impossible with an automatic gearbox).
Angl-C6-page001-21-2005 4/02/05 17:12 Page 10

Downloaded from www.Manualslib.com manuals search engine 19
GENERAL
LUBRICANTS - TOTAL recommended oils
Gearbox oil
Engine coolant
All countriesCITROËN fluid
Protection: -35C°2Litres
5Litres
20 Litres
210Litres9979 70
9979 71
9979 76
9979 779979 72
9979 73
9979 74
9979 75 PacksCITROËN references
REVKOGEL 2000 GLYSANTIN G33 AM6 automatic gearbox All countriesJWS 3309 (ESSO)
Synthetic brake fluidAll countriesCITROËN fluid
1/2Litre
DOT 4 Packs
CITROËN references Power steering oil
Power-assisted steering All countriesLDS TOTAL H50126
Hydraulic circuit
All countriesColour
1Litre
TOTAL FLUIDE LDS Packs
CITROËN references Norm
Orange
Angl-C6-page001-21-2005 4/02/05 17:12 Page 19

Downloaded from www.Manualslib.com manuals search engine 103
CLUTCH
GEARBOX
TRANSMISSION
PROCEDURE PRIOR TO OPERATIONS: AM6 AUTOMATIC GEARBOX
If a gearbox malfunction occurs, there are two possible configurations
depending on the seriousness of the fault:
- Gearbox in back-up mode with a replacement programme of (the fault
values are taken in substitution).
- Gearbox in back-up mode with an emergency programme (3rd hydraulic).
WARNING: In the emergency programme, an impact is felt when
changing P/R or N/R.
Reception of the customer.
Discuss with the customer, to find out all the malfunction symptoms.
Oil quality.
If the gearbox has suffered a serious fault resulting in a malfunction or
the destruction of a clutch, the oil will overheat and become
contaminated with impurities: the oil is said to be «burnt».
This is characterised by a black colour and the presence of an
unpleasant smell.
ESSENTIAL: The gearbox must be replaced.Oil level.
Preliminary conditions:
- Vehicle horizontal, parking brake off.
- Check that the gearbox is not in back-up mode (using a diagnostic tool).
- The oil temperature should be 60°C (+8, -2)(using a diagnostic tool).
- Press on the brake pedal, change through all the gears.
- Place the gear lever in position P.
With the engine running at idle, without power consumers (aircon,
heating, etc.):
- Remove the oil level plug.
The oil should flow out, then drip-drip.
Refit the oil level plug (the oil level is correct).
The oil does not flow out through the oil level plug (see operation: drain
fill - bleed the gearbox).
Engines: ES9A - DT17BTED4
Angl-C6-page101-120-2005 4/02/05 17:25 Page 103

Downloaded from www.Manualslib.com manuals search engine 109
CLUTCH
GEARBOX
TRANSMISSION
AM6 GEARBOX CONTROLSNOTE:The vehicle is equipped with «shift lock». It is necessary to switch on the ignition and
press the brake pedal to release the selection lever from position "P".
The switch "a"positioned on the gear control panel allows the driver to choose one of the
following 3 driving programmes:
- Normal programme:The normal programme operates in the absence of any other selection
being made (auto-adaptive mode ; eco law).
- Sport programme:The sport programme permits a more dynamic driving style, with greater
performances and acceleration.
- Snow programme:The snow programme facilitates moving off and traction on ground that
has limited adhesion.
To revert to the normalprogramme, you have to press a second timeon the sportor snow
switch.
B2CP430D
Engines: ES9A - DT17BTED4
Angl-C6-page101-120-2005 4/02/05 17:25 Page 109

Downloaded from www.Manualslib.com manuals search engine 111
CLUTCH
GEARBOX
TRANSMISSION
AM6 GEARBOX CONTROLS: «SHIFT LOCK» FUNCTIONIMPERATIVE: Respect the safety and cleanliness requirements, with reference to the brochure:
«Recommendations-Precautions».
The «shift lock»is a system that locks the gear selection lever in position «P».
Unlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed.
Move the gear selection lever out of position «P».
Unlocking the «SHIFT LOCK» (with an operating fault).
Should it be impossible to unlock the «shift lock»with the «Normal operation»method.
The fault may originate from one of the following components:
- «Shift lock».
- Gear lever position switch.
- Automatic gearbox ECU.
- Electrical harness.
- Battery voltage.
Operations to be performed.
Unclip the cover (1).
Unlock the «shift lock»by pressing at "a"with the aid of a screwdriver (screwdriver with a minimum length of
150 mm).
Move the gear selection lever out of position "P".
C5FP0RCD
Engines: ES9A - DT17BTED4
C5FP0RBC
Angl-C6-page101-120-2005 4/02/05 17:25 Page 111

Downloaded from www.Manualslib.com manuals search engine 115
CLUTCH
GEARBOX
TRANSMISSION
DRAINING, FILLING AND TOPPING UP THE AM6 AUTOMATIC GEARBOX
WARNING: Do not take account of the information mentioned on tool [1].
Oil capacity for a dry gearbox: 7 litres (approx.).
Type of oil: JWS 3309 ESSO(red in colour).
Volume of oil remaining after draining: 4 litres (approx.).
Quantity of oil to be added: 3 litres (approx.).
Refit the filler plug (3)(with a new seal).
Tighten the plug (3)to: 4 ± 1 mdaN.
Initialise the oil usage counter (follow the procedure in the diagnostic tool).
Checking the oil level.
Prior conditions:
- Vehicle in a horizontal position.
- Check that the gearbox is not in back-up mode.
Remove the filler plug (3).
Add 0.5 litreof extra oil into the gearbox.
Press the brake, change through all the gears.
Gear lever in position "P".
Engine running, at idle:
- Oil temperature 60°C (+ 8 ; - 2)(parameter measures with a diagnostic tool).
- Remove the level plug (2).
B2CP3WZCB1BP317C
Angl-C6-page101-120-2005 4/02/05 17:25 Page 115