clock setting CITROEN C6 2005 Owners Manual

Downloaded from www.Manualslib.com manuals search engine 54
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: ES9A
Setting the valve timing (continued).
Refitting.
Check that the camshafts and the crankshaft are correctly pegged.
Check that the rollers and the coolant pump pulley are turning freely (no tightness).
Loosen the camshaft pulley screws by a 1/4 turn.
Make sure that the pulleys are turning freely on the camshaft hub.
Turn the camshaft pulleys in a clockwise direction, to end of slots.
WARNING: Respect the direction of fitting of the belt: Facing the timing, the inscriptions on
the belt should be readable the correct way up.
Fit the timing belt on the crankshaft pinion.
Position the tool [6].
Position the timing belt in the following sequence (belt well tensioned):
- The roller (26), the pulley (18), the pulley (17).
WARNING: Keep the timing belt well tensioned.
- Refit the guide roller (16), tighten to 8 ± 0,8 m.daN.
Position the timing in the following sequence:
- The camshaft pulleys (15)and (14), the tensioner roller (24), the coolant pump pulley and the
guide roller (27).
NOTE: When positioning the belt on the camshaft pulleys, turn these clockwise so as to engage the
next tooth. The angular displacement of the pulleys should not be more than the equivalent of one
tooth.
B1EP15VDB1BP2BLC
Angl-C6-page022-82-2005 4/02/05 17:19 Page 54

Downloaded from www.Manualslib.com manuals search engine 56
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: ES9A
Tighten the nut (23)of the tensioner roller (24), tighten to 1 ± 0,1 m.daN.
Check that the exhaust camshaft pulley screws are not at the end of slots (by loosening one screw).
WARNING: Otherwise, restart the operation for positioning the timing belt.
Tighten at least 2 screwsper exhaust camshaft pulley to 1 ± 0,1 m.daN.
Remove the tools [1], [2]and [4].
Rotate the crankshaft 2 turnsin a clockwise direction.
IMPERATIVE: Never turn it back.
Peg the crankshaft, using tool [2].
Peg the camshaft pulleys, using tool [1].
Slacken the nut (23)of the tensioner roller (24).
B1EP15WCB1EP15XC
Angl-C6-page022-82-2005 4/02/05 17:19 Page 56

Downloaded from www.Manualslib.com manuals search engine 57
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: ES9A
Tensioning the timing belt.
Act on the tensioner roller (24)so as to align the marks «c»and «d», without detensioning the timing belt
(failing this, restart the operation of adjusting the belt tension).
Hold the tensioner roller (24).
Tighten the nut (23), tighten to 1 ± 0,1 m.daN.
Check the position of the tensioner roller (the alignment of the marks «c»and «d»should be correct).
Remove the tools [1], [2]and [4].
Turn the crankshaft 2 rotationsclockwise.
IMPERATIVE: Never turn it back.
Peg the crankshaft, using tool [2].
Check the position of the tensioner roller (the alignment of the marks «c»and «d»should be correct).
Peg the camshaft pulleys, using tool [1].
If the peg [1]goes in: Loosen the exhaust camshaft pulley screws by 45°.
If the peg [1]does not go in: Slacken the exhaust camshaft pulley screws by 45°.
Bring the exhaust camshaft hub to the pegging position (5), using tool [5].
WARNING: Check that the exhaust camshaft pulleys are not at the end of slots. Otherwise, restart
the operation to position the timing belt.
Tighten the exhaust camshaft pulley screws to 1 ± 0,1 m.daN.
Remove tools[1] and [2].
Complete the refitting.
Initialise the injection ECU (see corresponding operation).
B1EP15XC
Angl-C6-page022-82-2005 4/02/05 17:19 Page 57

Downloaded from www.Manualslib.com manuals search engine 64
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: DT17BTED4
Peg the camshafts, using tools [3]at "h"and "g".
Slacken:
- The 3 screws (15)of the camshaft pulley (23).
- The 3 screws (17)of the camshaft pulley (18).
- The screw (21)of the tensioner roller (20).
Remove the timing belt (22).
Checks.
IMPERATIVE: Just before refitting, carry out the checks below.
Check that the rollers (16), (20)and (19)and the coolant pump (14)can turn freely (without play
and without any tight spot).
Check that there are no signs of oil leaks (from the crankshaft and camshaft seals).
Check that there are no signs of coolant leaks (from the coolant pump).
Replace components that are faulty (if necessary).
Refitting.
Reposition the timimg belt on the crankshaft pinion (24).
Hold the timing belt (22)in position, using tool [4].
Tighten the screws (15)and (17)by hand.
Turn the camshaft pulleys (23)and (18)clockwise, to place them at the end of slots.
B1EP1JFDB1EP1JGC
Angl-C6-page022-82-2005 4/02/05 17:19 Page 64

Downloaded from www.Manualslib.com manuals search engine 65
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: DT17BTED4
Reposition the timimg belt, strip «j»well tensioned, in the following order:
- Guide roller (19).
- Camshaft pulley (18).
- Guide roller (16).
- Camshaft pulley (23).
- Tensioner roller (20).
NOTE:If necessary, turn the pulleys (23)and (18)slightly anti-clockwise (the offset must not be
more than one tooth).
Remove the tool [4].
Using a hexagonal spanner, rotate the tensioner roller (20)anti-clockwise.
Position the index "l"facing the notch "k".
Tighten the screw (21) : 2,5 ± 0,2.
Remove the screws (15)and (17)from the pulleys (23)and (18)in order to check that the screws
(15)and (17)are not at the end of slots.
IMPERATIVE: If the screws (15) and (17) are at the end of slots, restart the operations to refit
the timing belt.
B1EP1JHDB1EP1JJC
Angl-C6-page022-82-2005 4/02/05 17:19 Page 65