spare wheel Citroen C6 2011 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2011, Model line: C6, Model: Citroen C6 2011 1.GPages: 216, PDF Size: 10.31 MB
Page 8 of 216
6
B
A
IN BRIE
F
1. Lift the boot fl oor using the strapB.2. Anchor the strap on the roof of
the boot.3. To remove the spare wheel,
detach the belt then push the
wheel forwards so as to be ableto lift it.
SPARE WHEEL
Note: The tools are to be found in a protective holder inside thespare wheel.
141
OPENING
This can be unlocked, vehiclestopped:With either the remote controlor the key.Using the interior central
unlocking button, or simply by
openin
g a door.
From the outside, press on lever A.
•
•
BOOT
To close, lower the boot using the
gripping handle located on the inte-
rior boot trim.
Press fi rmly shut.
84
GLASS SUN ROOF
The sun roof is operated by theelectrical controlA.
An action to the fi rst notch of thecontrol starts a movement whichstops as soon as you release thecontrol.
An action to the second notch of
the control opens or closes the sunroof fully. A further action stops themovement.
118
Page 24 of 216
22
Limit the causes of excess
consumption
Spread loads throughout the
vehicle; place the heaviest items
in the bottom of the boot, as close
as possible to the rear seats.
Limit the loads carried in the
vehicle and reduce wind resist-
ance (roof bars, roof rack, bicycle
carrier, trailer...). Use a roof box
in preference. Remove roof bars
and roof racks after use.
At the end of winter, remove
snow tyres and refi t your summer
tyres.
Observe the recommendations
on maintenance
when cold, referring to the label in the door aperture, driver's side.
Carry out this check in particular:-before a long journey,-at each change of season,-after a long period out of use.
Don't forget the spare wheel and
the tyres on any trailer or caravan.
Have your vehicle serviced regu-
larly (engine oil, oil fi lter, air fi lter...)
and observe the schedule of oper-
ations recommended by the manu-
facturer.When refuelling, do not continue
after the 3rd cut-off of the nozzle
to avoid any overfl ow.
At the wheel of your new vehicle,
it is only after the fi rst 1 800 miles
(3 000 kilometres) that you will
see the fuel consumption settle
down to a consistent average.
Page 50 of 216
48
II
TRIP COMPUTER
Tyre defl ation alert
TheSERVICEwarning lamp comes on and a vehicle outline is displayed.
The location of the wheel(s) concerned is clear from the vehicle outline, on which the affected wheel(s) will be fl ashing.Check the tyre pressures as soon as possible.
Colour screen C NaviDrive colour display
Tyre very defl ated
Tyre defl ated
Stop immediately, avoiding any sudden actions with the steering wheel or the brakes.
Chan
ge the wheel with the affected tyre (whether punctured or very defl ated), then have the tyre repaired and
all the pressures checked at the earliest opportunity.
The wheel with a damaged tyre (either in the boot or under repair) can no longer be detected (informationgiven by the vehicle outline or by a message) nor is the spare wheel able to be detected.
Puncture
The"STOP"and tyre(s) punctured warning lamps light up, and a vehicle outline is displayed. The location of the
wheel(s) concerned is clear from the vehicle outline, on which the affected wheel(s) will be fl ashing.
Colour screen CNaviDrive colour display
Page 51 of 216
49
II
TRIP COMPUTER
Wheel not detected
TheSERVICEwarning lamp comes on and a vehicle outline is displayed.
The wheel(s) concerned can be identifi ed from the vehicle outline, on which it (they) will be missing. If you have notchanged a wheel, such information indicates that the system is malfunctioning.
Contact a CITROËN dealer or a qualifi ed workshop for the replacement of the faulty sensor(s).
Colour screen CNaviDrive colour display
The defl ation detection system is a driving aid, but which does not absolve the driver from the need to be vigilant andresponsible.
This system does not remove the need to check the tyres on a regular basis (see "Vehicle identifi cation"), to makesure that the vehicle is behaving correctly and to avoid premature tyre wear arising from driving too fast etc.
Do not forget to check the pressure in the spare wheel.
All repairs or replacement of tyres on wheels fi tted with sensors must be done by a CITROËN dealer or a qualifi ed workshop.
The system may suffer from temporary interference caused by radio transmissions on neighbouringfrequencies.
Page 119 of 216
117
III
5
4
4
1
3
2
6
1Pull strap (spare wheel stowage).2Boot lamp.To change the bulb, detach the cover and use a W 5 W bulb.
3 Elastic straps.4 12 V accessories socket (functions with the ignition switched on).
5 Boot lateral net.6 Changer for 6 CDs.
BOOT
Page 137 of 216
135
V
A
B
and change the bulbs.Note: The tool for undoing thescrews is to be found in the toolbox in the spare wheel. See "Changing a wheel".
REAR CENTRAL LENSAReversing lampBFoglamp
The bulbs for lam
ps Aand Bhavea common bulb-holder. Contact
a CITROËN dealer or a qualifi ed
wor
kshop.
THIRD STOPLAMP
Contact a CITROËN dealer or aqualifi ed workshop.To
gain access to the bulb-holders, open the boot and undo the four
screws on the bodywork. Then lower
the boot lid in order to be able to pull out the two rear lamp units, without
pulling on the electric cables.
NUMBER PLATE
Detach the transparent shield, then pull out the bulb. Bulb: W 5 W.
After each operation,check that the lampswork.
CHANGING BULBS
Page 142 of 216
14 0
V
COLD WEATHER SHIELD
After fi tting Before fi tting
FITTING/REMOVAL OF THE
SNOW-GUARD
Fitting
Clip the snow-guard onto the ribs
of the bumper.
Removal
To detach the snow-guard, slide
the tool4 into the recesses in thesnow-guard and lift.Note:The tool 4 is to be found 4in the protection box in the sparewheel. See "Changing a wheel".
The snow-guard delivered with the vehicle (accordingto destination) should be fitted during the winter period,but removed for the remainder of the year.
It is essential to remove it whenever the temperature is above10 °C.
Page 143 of 216
141
V
4
3
8
9
61
2
5
7
CHANGING A WHEEL
ACCESS TO THE SPARE WHEEL
To access the spare wheel1.Lift the boot fl oor by means of the strap.2.Anchor the strap on the roof of the boot.3.To remove the spare wheel, detach the belt then push the wheelforwards so as to be able to lift it.
TO REPOSITION THE SPARE WHEEL
To put the spare wheel back in the boot1.Position the spare wheel fl at in the boot, then pull it towards you.2.Next place the toolbox inside the wheel, then secure the assembly with
the belt.3.Release the strap to return the boot fl oor to its initial position.
Tyre pressures
Tyre pressures are indicated on the label which is positioned low down on
the front pillar. See "Vehicle identifi cation" and "User Precautions". (On this label you will see a pressure for normal speeds and a pressure for high speeds).
1.Handle2.Jack3. Tool for removing/refi tting the
wheel bolts4. Tool for removing the anti-theft
bolt protector
5. Centring guide6. Tool for removing foglamps
and reversing lamps
7. Handle extension8. Towing eye9. Movable chock
TOOLS
The tools are to be found in a pro-
tective holder inside the spare
wheel. Pull back the retaining strap
t
o have access.
Page 144 of 216
142
V
Before positioning the jack, always adjust the vehicle's groundclearance to the "maximum height" position and retain thisadjustment for as long as the jack is under the vehicle (do notuse the hydraulic adjustments).
Never get underneath the vehicle if it is supported only by thejack.
The jack and all the tools are designed specifi cally for use on your particular vehicle. Do not use them for any other applications.
Have the original wheel repaired and refitted as soon aspossible.
It is imperative not to exceed a speed of 80 km/h (50 mph) onthe spare wheel.
REMOVAL1. Park the vehicle on stable, fi rm ground that is not slippery. Apply the
parking brake.2. It is essential to make sure that the occupants have left the vehicle and are in a place where their safety is guaranteed.3. With the engine idling, adjust the ground clearance to maximum height. See "Comfort" and "Ground clearance adjustment". Switch off the igni-
tion and engage fi rst gear or reverse gear depending on any slope (for a vehicle with automatic gearbox, select position P).4. Position the chock at the wheel that is diametrically opposite the one to
be replaced.
5. Position the jack at one of the four jacking-points provided on the sub-
frame close to the wheels, then use the handle to unwind the jack until
it reaches the ground.
6. Slide the removal tool4 into the notch and lever vigorously to detach
the anti-theft bolt protector. See illustration. You can use the handle at
the extremit
y of the tool 4.7.Slacken the wheel bolts.8. Continue to extend the jack until the wheel is a few centimetres off the ground.9. Undo the bolts, remove the wheel.
CHANGING A WHEEL
Page 145 of 216
143
V
It is imperative not to exceed a speed of 80 km/h (50 mph) onthe spare wheel.
The wheel bolts are specifi c to the type of wheel.
When replacing wheels, check with a CITROËN dealer or aqualifi ed workshop that the wheel bolts are compatible withthe new wheels.
Note: take care to note down the code number engraved on thehead of the anti-theft bolt socket. This will enable you to obtainreplacement anti-theft bolt sockets from a dealership.
WHEEL FOR TEMPORARY USE
If your vehicle is equipped with aspare wheel for temporary use
only, when fi tting it it is normal toobserve that the wheel bolts do notcome to bear on the wheel rim.
The spare wheel is secured by theconical tapering of the wheel bolt’sshaft. See illustration.
When refi tting the original wheel,ensure that the wheel bolt contactsurfaces are clean and in goodcondition.
REFITTING A WHEEL1. Fit the wheel on the hub,using the centring guide. Make sure that the contact surface between the hub and the wheel
is clean.2. Screw in the bolts but do not
fully tighten them.3. Lower the jack and remove it.4. Tighten the wheel bolts, usingthe wheelbrace.
5. Refi t the embellisher.
6. Return the ground clearance
to the normal position. See "Ground clearance adjustment".7.Ensure the tyre pressure
is correct (see "Vehicle
identifi cation") and have the balancing checked.
WHEEL EQUIPPED WITH DEFLATIONDETECTION SENSOR
Such wheels have tyre pressuresensors. Have it repaired by aCITROËN dealer or a qualifi edpy
workshop.
ANTI-THEFT BOLTS
Each wheel is equipped with oneanti-theft bolt.
To remove it1. Remove the protector that is covering it by means of the
tool 4 for "removing anti-theft protectors".2. Use the anti-theft socket with
the handle.
CHANGING A WHEEL