engine Citroen CX 1978 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 2 OPERATION No MA. 420.0 : (:h ’ k’ j I/ cc ,,I:, > BEM MULLER
665 Junior
Proceed as for front wheels
at front : 165 mm
He;@/ ,),~ns,,r‘,,,,~,,,,s lo be srn,p,,lmosly ‘rcs,wrlcd Ior /his rhrck
at rem : 215 mm ~Saloo,rsJ
a : 228
mm f Estatus J V&e of the camber angle : On
-024’

Downloaded from www.Manualslib.com manuals search engine SUSPENSION
OPERATION No MA. 430-00 : ( hnmrtcristics mrd spccinl jeatrrres oj /ha susp~~sio~~. Op. MA. 430-00 1
FRONT SUSPENSION
f
c
s
6
-E
J REAR SUSPENSION
I
,

Downloaded from www.Manualslib.com manuals search engine I. CHARACTERISTICS
..-.-..- --~~~
HEIGHT CORRECTOR
SUSPENSION CYLINDER ( All Saloon vehicles )
L.43-6
SUSPENSION CYLINDER ( Estate vehicles )
-- --.

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 430-00 : (lsnmr/eris/irs nvrl .s/jrrinl /c,n/uws 0, /he susfiv,,sias Op. MA. 430-00 3
MANUAL HEIGHT CONTROL
‘hi anual height control quadrant :
I. High position
II. Intermediate high position
III. Normal driving position
IV Low position
G Assembly diagram for manual height control
:
L.43.2
Seen along Fl

Downloaded from www.Manualslib.com manuals search engine VEHICLE HEIGHTS 13454
- Front height measured from point SG a 8) of the subfrome. to the surface on which the vehicle is stondinq
_ Rear height measured from point (, b )B of the subfrome to the surface on which the vehicle is standinq Calibration pressures :
FRONT REAR
\// \~~lr~r,,i J v/xii
/c,.5 I:\lol,‘s
_ Identification mark on filler plug 75 40 35
- Calibration pressure ( /or rhc’rkiqg 1. 75 2 bars 40 2 bars
- 27 - 15 35 1 ;, bars
(1088 _ ;;, P51 1
(580 : ;;, P51 i ( 508; :',, PSP 1 Dampers
- They are incorporated in the pneumatic units
NOTE The front and rear dampers ore different on CX 2400 GTI vehicles and therefore the pneumatic units are PNEUMATIC UNITS :
Volume of front units i Soloor, mid I:s/fll<,s 1
500 cc f Pressed steel type )
Volume of rear units
i All Saloons 500 cc ‘j Pressed steel type)
Estates 700 cc (Screwed in type i
I
specific. Suspension cylinders :
Diameter of pistons ,,,, Height
corr&tors : Identical front and rear Anti-roll bar :
23 mm i lisfoir~s mid o/l Salormc <~,c,,,,, ( Y ‘Xl(i VII I
Diameter of front anti-roll bar.
i 24 mm , (. 2400 (.‘/I J
Diameter of rear anti-roll bar 17.5 mm
NOTE The rear anti-roll bar on Estates and on Saloons is different.

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 430.00 : c ,,<,,a< ,<,r;s,;rs mi/ .s/wrin/ ,vn/srrs oi /he srmf~rw.~ion Op. MA. 430-00 5
II. SPECIAL FEATURES
Adjusting the anti-roll bars :
A, t/xv ,ms,
- Lateral positioning equal protrusion on either side to within 2 mm
- Anti-roll bar bearing preload 300 N ( 30kg) ( 66 lb )
- Lateral clearance of anti-roll bar. under pressure of 500 N i 50kq I( 110 fb i 0.2 to 1 mm
,I, l/X“ rcnr :
- Lateral positioning same thickness of shim on both sides. within 1 mm
- Shimming, if necessary. level with the split collars to within 0.6 mm
Greasing of the suspension piston con-rod ioint :
( Carried out with LHM liquid contained in the dust cover )
- Front suspension cylinder
- Rear suspension cylinder
Upper front wheelarm stops :
WARNING ‘,hc ,,,;,,,i<~, ~,op ,,,I (i, he ii,,, r/ 01 //I< ,,I?<,<‘/ wd. 7cm3
25 cm3
Tightening torques :
- Anti-roll bar link-rod on upper wheelarm. i Bush nut 3 doNm ( 21 11 2 ft.lb )
NYLSTOP nut 4.5 to 5daNd32 1/‘2to 36ft.lb)
- Link-rod on anti-roll bar 4.5 to SdaNm(32 1/2to36ft.lb)
. Screw securing front anti-roll bar bearing 2.7 daNm ( 19 l/2 ft.lb )
^ - Clamps for adjusting pie-load on front anti-roll bar 13 doNm ( 9 l/2 ft.lb)
b2 - 1.5 daNm [ 11 ft.lb i
0 Clomp for height corrector control
rod ( front and rem )
”
6 daNm ( 43 l/ 2 ft.lb ) - . An+iwroff bar 0” rear &&arm ( rear fixing
points ) I /nc<’ nvrl /hrcn,l~r &
- Rear anti-roll bar split collars :
cc
-5 Tightening torque for screw ( 1 )
according to width (e) of bearing :
:
2
e = 5 mm 8 d.aNm ( 58 ft.lb ) f -I’, I’JiS,
P
e-6mm lOdoNm( lOft.lb)i 121Vi-’
Fitting of the front and rear wheelarm stops using water
Fitting of the front anti-011 bar bearing shells using ,< TOTAL MULTIS I) grease.

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 430-O : Checking md ndjusting the suspcusion and its control. 06. MA. 430-O i
ADJUSTING THE HEIGHTS
AT FRONT : Between under-face of point (c o ))
subfrome ond point of contoct of wheels with
ground.
AT REAR : Between under-face of point <( b a)
subfrome ond point of contact of wheels with
ground.
1. Check tyre pressures.
2. Remove corrector protectors and make sure the
manual control rods are not exerting pressure on
levers ( 1) and ( 2).
3. Slightly loosen automatic control clump and
adjust to obtain :
3
Front height = 165 ? 8 mm
Rear height = 215 ? 8 mm ( Saloons )
228 t 8 mm ( Estates )
Tightening torque of clomps = 1.5 doNm (11 ft.lb )

Downloaded from www.Manualslib.com manuals search engine 2 OPERATION No MA. 430-O : ~hwki~zg nrtd nrijustittg the suspwrsiott ntd its cotttrol
4. Adjusting the height control :
Slacken nuts ( 1) and (4 )
Set control levers ( 2 ) and ( 3 ) to obtain :
Jl = J2
J3 = J4
Tighten nuts ( 1 ) and (4).
5. Check the heights :
Ertgittv icilittg. tttnttt~nl cotttrol Ic,t’c,r itt ttotvttO/
rtrrtttiug positiott.
Check that ball join!s of front and rear corrqctors
are not jammed in their forks.
At front :
a) Raise the vehicle by hand.
b Release when weight becomes too great to
support.
Vehicle wi1.l drop, then rise again and
stabilize itself. Note front height.
Push vehicle down by hand
Release when resistance becomes too great.
Vehicle will rise again then drop and stabi-
lize itself.
Note front height again.
c) Take the average of these two measurements
which should be between
157 and 173 mm inclusive
At rear :
Proceed in the same manner.
Average of height readings should be between
210 and 220 mm inclusive ( Saloons )
220 and 236 mm inclusive ( Estates )
7. Fit front and rear protectors.

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine STEERING
OPERATION No MA. 440-00 : (Ihnrnctrristics nlld spcrt’nl ic;atrrrcds oi the sfvc~tir~g Op. MA. 440-00 1