differential Citroen CX 1980 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 2. Lubrication :
- Type of oil
- Capacity
- Difference between min and mox on dipstick TOTAL EP 80
1600 litres (2.8pts)
C.150 litres (0.26pts)
3. Gem control :
- Floor mounted gear lever Gear Pattern
Il. SPECIAL FEATURES
Adjustments :
- lst/ 2nd gear synchro hub endfloot
_ Endfloot of half rinqs between 1st and 2nd qear pinions
- Clearance between beorinq split pin and qearbox cosinq
= Differential bearing pre-loud Adjusting the selector shaft stops : L/35 mln rnclx.
0.05 mm max.
3.05 mnl mox
c.15 mm
- Adjusting the 3rd gear stop I , Smear thread of stop-screw ( I ) with sealing compound.
Engage 3rd qear. with 3rd/ 4th qear slidinq pinion restinq aqainst 3rd qear idlinq pinion
Brinq the stop-screw into contact with selector shaft then screw it in one turn in order to obtain CI clearonce
between the selector shaft and the face of the groove of the slidinq pinion.
Tiqhten locknut ( 2 ).
Proceed as above ( stop-screw a< 3 > and locknut ,< 4 /> )
.2
Adjusting the 3rd gear stop idjustinq the 4th gear stop

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 330.00 : ( l~nmrtvrisfirs SPECIAL FEATURES
Adiustments :
Endflaot of 1st: Rev gear sjnchro hub 0.35 mm max.
Endfloat of half-ring between
1st and 2nd gear pinions 3.05 nlm nlax.
Clearance between beorinq split pin and gearbox casing c.05 mm nlax.
Differential bearing overoll pre-load 0 15mm Adiusting the selector shaft stops ;
Smear thread of stop screw ( 1) with CURTYLON
Engage 2nd qear. with 2nd/3rd gear sliding pinion resiinq against 2nd gear idling pinion.
$ Bring stop-screw into contaci with selector shaft, then screw it in 1 ‘2 a turn. in order to obtain o clearance
of 0.4 io 0.7 mm between the selector fork and the face of the slidinq pinion groove
7
m Tighten locknut ( 2 ! - Adjusting the 3rd gear stop ( cm lx
rorric,d out rrith pnrbov iu situ I
Proceed ~1s above. j stop-screw (< 3 >) and locknut e 4 1) !.

Downloaded from www.Manualslib.com manuals search engine ii. SPECIAL FEATURES
Adjustments :
- Endfloat of lW2nd gear synchio nuts
0.05 mm max.
- Endfloot of half-ring between 2nd and 3rd gear pinions GO5 mm mox
- Clearance between bearing split pin and gearbox casing
0.05 mm nlax.
- Overall prelood on differential bearinq
0.15 mnl Adjusting the selector shaft stops :
. Adjusting the stop for 3rd and 5th gears / ,g< nrhov lI~n,r,, vd ,
Smear thread of stop-screws (1 ) and ( 2) with sealing compound.
Engage 3rd qear with 3rd and 4th qeor sliding pinion resting against 3rd gear idling pinion.
Bring,stop-screw ( 1) into contact with selector shaft, and scw.v it in one turn, to obtain the correct clearance
between the selector fork and the sliding pinion groove.
Tighten lock-nut.
Proceed in the some manner to adjust stop-screw ( 2) for 5th qear.
Adjusting the 3rd and 5th gear stop~screws