boot Citroen DS3 2011 1.G User Guide

97Access
System which provides full manual locking or
unlocking of the doors from the inside.












Manual centralised control


Locking



)
Press button A
to lock the vehicle.
The red indicator lamp on the button comes on.


Unlocking



)
Press button A
again to unlock the vehicle.
The red indicator lamp on the button
switches off.
If one of the doors is open, central
locking from the inside does not take
place. If the vehicle is locked from the outside,
the red indicator lamp flashes and
button A
is inactive.


)
In this case, use the remote control
or the key to unlock the vehicle.




Automatic centralised
control
System which provides full automatic locking
or unlocking of the doors and the boot while
driving.
You can activate or deactivate this function.


Locking

When the speed exceeds 6 mph (10 km/h), the
doors and the boot lock automatically.

Unlocking



)
Above 6 mph (10 km/h), press button A
to
unlock the doors and the boot temporarily.
If one of the doors is open, the
automatic central locking does not take
place.
If the boot is open, the automatic
central locking of the doors is active.

Activation



)
Press button A
for more than two seconds.
A confirmation message appears on the
multifunction screen, accompanied by an
audible signal.


Deactivation



)
Press button A
again for more than
two seconds.
A confirmation message appears on the
multifunction screen, accompanied by an
audible signal.
To lock or unlock the doors mechanically in the
event of a central locking system failure or flat
battery.









Emergency control


Locking the driver's door



)
Inser t the key in the lock, then turn it to the
right.



Unlocking the driver's door



)
Inser t the key in the lock, then turn it to
the left.



Locking the passenger's door



)
Remove the black cap, on the edge of the
door, using the key.

)
Inser t the key in the cavity, then turn it fully.

)
Remove the key and refit the cap.



Unlocking the passenger's door



)
Pull the interior door opening control.

In the event of a fault with the central
locking system, you must disconnect
the battery to lock the boot and
so ensure the complete locking of
the vehicle.

99Access











Boot


Opening



)
After unlocking the vehicle using the
remote control or the key, pull the handle
and raise the tailgate.



Closing



)
Lower the tailgate using the interior grab
handle.
If the tailgate is not closed correctly:


- when the engine is running
,
this warning lamp comes on,
accompanied by a message
on the multifunction screen for a
few seconds,

- when the vehicle is moving
(speed above
6 mph (10 km/h)), this warning lamp comes
on, accompanied by an audible signal and
a message on the multifunction screen for
a few seconds.
System for mechanical unlocking of the boot
in the event of a battery or central locking
malfunction.






Ta i l g a t e r e l e a s e


Unlocking



)
Fold back the rear benchseat to gain
access to the lock from inside the boot.

)
Inser t a small screwdriver into hole A
of the
lock to unlock the tailgate.

111Visibility





LED lamps
Daytime external lighting using specific front lamps providing a signature of the vehicle. Comprising
two sets of six light emitting diodes (LEDs), they are located in the ver tical scoops below each
headlamp.

On starting the vehicle, in daylight the LED
lamps come on automatically, if the lighting
stalk is in position "0"
or "AU TO "
.
If the sidelamps and headlamps are switched
on manually or automatically, the LED lamps
switch off. For countries where exterior lighting by day is
not a legal requirement, you can activate or
deactivate the function via the multifunction
screen configuration menu.




Headlamp
adjustment
To avoid causing a nuisance to other road
users, the height of the headlamps should be
adjusted in relation to the load in the vehicle.

0

.
Driver only or driver + front passenger.

-
.
Intermediate setting

1.
5 people.

-
. 5 people + load in the boot.

2.
Driver only + maximum authorised load in
the boot.
This position is sufficient to avoid causing dazzle.

Higher settings may limit the spread of light
from the headlamps.
The initial setting is position "0"
.


Programming

In countries where it is a legal
requirement:


- this function is activated by default
and cannot be deactivated,

- in daylight, the sidelamps and
number plate lamps also come on,

- If the sidelamps or headlamps
are switched on manually or
automatically, the LED lamps
switch off.
For versions not fitted with LED lamps,
it is the dipped beam headlamps that
come on automatically on star ting the
vehicle.

11 7Visibility








Interior mood lighting
The dimmed passenger compar tment lighting improves visibility in the vehicle when the light is poor.


Switching on

At night, the illumination of footwells and the
central dashboard storage compartment comes
on automatically when the sidelamps are
switched on.


Switching off

The interior mood lighting switches off
automatically when the sidelamps are
switched off.
It can be switched off manually using the
instrument panel lighting rheostat button.


)
With the lighting on, press several times on
the left hand button of the instrument panel
to progressively reduce the dashboard
lighting level.

)
Press again to reduce the lighting level
to the minimum and switch off the interior
mood lighting.
This comes on automatically when the boot is
opened and switches off automatically when
the boot is closed.





Boot lamp

Different lighting times are provided:


- when the ignition is off,
approximately ten minutes,

- in energy economy mode,
approximately thirty seconds,

- when the engine is running, no limit.

006
Fittings


The section describes the various interior fittings, the glove box,
the central armrest for storage, the Jack socket or USB port for
connecting a portable player, the mats for protecting the carpet, as well
as the various boot fittings.

1.
Rear parcel shelf


(see the following page for details)

2.
Retaining strap


3.
Location for Hi- Fi amplifier


4.
Stowing rings


5.
Storage box (version equipped with a
temporary puncture repair kit)


(see the following page for details)
or
Tool box (version equipped with a spare
wheel)


(refer to section "Practical Information -
§ Changing a wheel")












Boot fi ttings

125Fittings

To remove the shelf:


)
unhook the two cords,

)
raise the shelf slightly, then unclip it on
each side.







Rear parcel shelf




)
Raise the boot carpet by pulling the strap
upwards to gain access to the storage box.
This has areas for storing a temporary puncture
repair kit, a box of spare bulbs, a first aid kit,
two warning triangles, ...





Storage box



)
refit the boot floor carpet by folding it
slightly in the middle.

Temporary puncture repair kit

Complete system consisting of a compressor
and a sealant car tridge which permits
temporary repair
of a tyre so that you can
drive to the nearest garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.



Access to the kit


The speed limit sticker I
must be affixed
to the vehicle's steering wheel to
remind you that a wheel is in temporary
use.
Do not exceed a speed of 50 mph
(80 km/h) when driving with a tyre
repaired using this type of kit.



Description of the kit



A.
"Sealant" or "Air" position selector.

B.
On "I"
/of f "O"
switch.

C.
Deflation button.

D.
Pressure gauge (in bar or p.s.i.).

E.
Compar tment housing:


- a cable with adaptor for 12 V socket,

- various inflation adaptors for
accessories, such as balls, bicycle
tyres...
F.
Sealant car tridge.

G.
White pipe with cap for repair.

H.
Black pipe for inflation.

I.
Speed limit sticker.
This kit is installed in the storage box, under the
boot floor.

Changing a wheel
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
The tools are installed in the boot under
the floor.
To gain access to them:


)
open the boot,

)
lift the boot carpet by pulling the strap
upwards,

)
remove the polystyrene storage box,

)
unclip and remove the box containing
the tools.


Access to the tools


List of tools

All of these tools are specific to your vehicle.
Do not use them for other purposes.

Wheel with trim


When removing the wheel
, first
detach the trim using the wheelbrace 1

pulling at the valve passage hole.

When refitting the wheel
, refit the
trim star ting by placing its cut-out at the
valve and press around its edge with
the palm of your hand.


3.
"Bolt cover" tool.
For removing the bolt protectors (covers)
on alloy wheels.

4.
Socket for the security wheel bolts (located
in the glove box).
For adapting the wheelbrace to the special
security wheel bolts (if your vehicle is fitted
with them).


1.
Wheelbrace.
For removing the wheel trim and removing
the wheel fixing bolts.

2.
Jack with integral handle.
For raising the vehicle.