bonnet Citroen DS3 2013 1.G Owner's Manual

CHECKS PRACTICAL
INFORMATIONTECHNICAL DATA AUDIO and
TELEMATICS
183 Bonnet
184 Running out of fuel (Diesel)
185 Petrol engines
186Diesel engines
187 Checking levels
190Checks
194 Temporary puncture repair kit
200 Changing a wheel
207 Changing a bulb
214Changing a fuse
221Battery
223Energy economy mode
224Changing a wiper blade
225 Towing the vehicle
227To w i ng a trailer
229Advice on care andmaintenance
230Accessories
234 Petrol engines
236Petrol weights
238LPG engines
239LPG weights
240Diesel engines
241Diesel weights
242 Dimensions
244Identifi cation markings
249Emergency or assistance
251MyWay
283 Audio system
012012013013010010011011

Familiarisation
90
Access
A.Unfolding/Folding the key.
B.Unlocking the vehicle.

Remote control key
1.Opening the fuel filler flap.
2. Opening and hooking the fuel filler cap.
Fuel t ank
102, 104
183
Ta n k c a p a c i ty:
- approximately 50 litres (petrol),
- approximately 46 litres (Diesel).
- (depending on version: approximately30 litres (petrol or Diesel)).
A.Interior release lever.B.
Exterior safety catch. C.
Bonnet stay.


Bonnet
Other functions...C.
Normal locking of the vehicle Vehicle location.

11Familiarisation
Instruments and controls
1.
Cruise control/speed limiter controls.2.Headlamp height adjustment. 3.Steering wheel adjustment. 4.
Lighting and direction indicator stalk
5. Instrument panel.
6.Driver's airbag.
Horn. 7. Gear lever. 8.12 V accessory socket
USB por t/auxiliary socket.9. Heated seat control. 10.Bonnet release lever.11.
Door mirror controls.
Electric window controls. 12. Fusebox.13.Stop & Star t switch
Electronic stability programme switch(ESP/ASR).14 .Front door window demisting/defrosting
vent. 15.Speaker (tweeter). 16. Windscreen demisting/defrosting vent.

Driving safely
Stop & Start
Going into engine STOP mode
170

The "ECO"warning lamp comes on
in the instrument panel and the engine
automatically goes into standby:
- with a manual
gearbox:
at speeds below
12 mph (20 km/h), when you put the gear lever in neutral, and you release the clutch pedal,

Going into engine START mode

Deactivation
/Reactivation

You can deactivate the system at any time bypressing the "ECO OFF"
switch the warning
lamp in the switchcomes on.
17
1

171

The system is automatically reactivated every time the engine is star ted withthe key.

Before refuelling or doing anything under the bonnet, you must switch off the ignition with the key. Th
e "ECO"
warning lamp goes off
and the engine restarts automatically:


-
with a manual gearbox:when you fullydepress the clutch pedal.
-
with a 5 or 6 speed electronic gearbox:at speeds below 5 mph (8 km/h), when you press the brake pedal or when you put thegear lever in position N .

-
with a 5 or 6 speed electronic gearbox
:


●
gear lever in position A
or M, when you
release the brake pedal,

●
or gear lever in position N
and brakepedal released, when you put the gear
lever into position A
or M
,

●
or when you engage reverse.

In certain circumstances, the ST
OP modemay not be available; the "ECO"
warning lamp
flashes for a few seconds, then goes off. In certain circumstances, STA R T m o d e m ay be
invoked automatically; the "ECO"warning lamp
flashes for a few seconds, then goes off.

11 7Visibility

Operating fault

If an automatic wiping fault occurs, the wipers
will operate in intermittent mode.
Have it checked by a CITROËN dealer or a qualified workshop.
To retain the effectiveness of the "flat-blade" wiper blades, it is advisable to:


- handle them with care,

- clean them regularly using soapywater,

- not use them to hold a sheet of cardboard against the windscreen,

- replace them at the first signs of wear.


Do not cover the rain sensor, linked with the sunshine sensor and located inthe centre of the windscreen behind the rear view mirror. Switch off the automatic wiping whenusing an automatic car wash.
In winter, it is advisable to wait until the windscreen is completely clear of ice before activating the automatic wiping.
This
position allows the wiper blades to be liftedfor winter parking, cleaning or replacement without damaging the bonnet.
In the minute following switching off of
the ignition, any action on the wiper stalkpositions the wipers vertically.
To park the wipers after this has been done,
switch on the ignition and operate the wiper stalk.
Vertical windscreen wiper
position

if the engine speed permits.
It is not necessary to release the accelerator pedal during gear changes. When braking or slowing down, the gearboxchanges down automatically so that the vehiclepicks up in the right gear.
Under full acceleration, the change up willnot take place unless the driver operates the gear lever or steering mounted control paddle(unless the engine is close to its maximumspeed).

Reverse

To e ngage reverse, the vehicle must be
immobilised with your foot on the brake. ) Select position R.


Stopping the vehicle

Before switching off the engine:


- change to position N
to be in neutral, or

- leave the vehicle in gear; in this case the
vehicle cannot be moved.
Manual mode
)Select position M.
The gears engaged appear in
succession in the instrument panel.
You can change mode at any time bymoving the gear lever from Ato Mor the other way round.
Never select neutral (position N ) when moving.
There is an audible signal onengagement of reverse.
For all parking situations, you mustapply the parking braketo immobilise the vehicle.

When immobilising the vehicle with theengine running, you must put the gear lever into neutral (position N).

Before doing anything under the bonnet, ensure that the gear lever is inneutral (position N ) and that the parkingbrake is applied. At low speed, i
f reverse gear is requested,
the Nwarning lamp flashes and the gearbox goes into neutral automatically.
To e ngage reverse, put the gear lever into
position N , then to position R.

The system is reactivated automaticallyat every new star t using the key.
Reactivation
This system requires a battery with a specialspecification and technology (reference numbers available from a CITROËN dealer
or a qualified workshop).
Fitting a battery not listed by CITROËN introduces the risk of malfunction of
the system. In the event of a fault with the system, the
"ECO OFF"
switch warning lamp flashes thencomes on continuously.
Have it checked by a CITROËN dealer or aqualified workshop.
In the event of a fault in STOP mode, the
vehicle may stall. All of the instrument panel
warning lamps come on. It is then necessaryto switch off the ignition and star t the engine
again using the key.


Operating fault
Maintenance


Before doing anything under the bonnet, deactivate the Stop & Start system to avoid any risk of injury resulting from automatic operation of STA R T mode.


The Stop & Start system makes use of advanced technology. All work
on this type of battery must be doneby a CITROËN dealer or a qualifiedworkshop. Pr
ess the "ECO OFF"switch again.
The system is active again; this is confirmed
by the switch warning lamp going off,accompanied by a message in the screen.

183Checks








Bonnet
Protects the components of the engine and provides access for checking levels.


Opening
)Open the front left door.)Pull the interior release lever A
, located at
the bottom of the door aper ture.
) Push the exterior safety catch Bto the leftand raise the bonnet. )
Unclip the bonnet stay Cfrom its housing, holding it by its foam protection.)
Fix the stay in the notch to hold the bonnetopen.

The location of the interior release lever prevents opening of the bonnet whilethe front left door is closed.

When the engine is hot, handle theexterior safety catch and the stay withcare.
Before doing anything under the bonnet, switch off the Stop & Startsystem to avoid any risk of injury resulting from an automatic change toSTA R T m o d e .

Closing








Running out of fuel
(Diesel)
If your vehicle is fitted with an HDI engine,
the fuel system must be primed if you run out of fuel.
This system consists of a priming pump and a
transparent pipe under the bonnet.
)Fill the fuel tank with at least five litres of
Diesel.)Open the bonnet. )Depending on version, unclip the cover togain access to the priming pump.)Squeeze and release the priming pump
until resistance is felt (could be from the
first application) and fuel appears in the
transparent pipe with the green connector. )Operate the star ter until the engine star ts.)Depending on version, put the cover back in position and clip it in place.)Close the bonnet.
If the engine does not star t at the firstattempt, do not try again. Operate the priming pump again, thenthe starter.
)Take the stay out of the support notch.)Clip the stay in its housing. )Lower the bonnet and release it at the end of its travel. )Pull on the bonnet to check that it is fully latched.

Changing the coolant

The coolant does not have to be changed.


Fluid specifi cation

The coolant must conform to the
manufacturer's recommendations.



Screenwash fluid level


Fluid specifi cation

For optimum cleaning and to avoid freezing,
this fluid must not be topped up or replaced
with plain water.

Take care when carrying out checks under the bonnet as some parts of theengine can be very hot (risk of burns).

Coolant level
Top up the level when necessary.
Th
e coolant level should be close
to the "MA X" mark but should never exceed it. When the engine is warm, the
temperature of the coolant is regulated by the fan. This can operate with the ignition off.
On vehicles which are fitted with a particle emission filter, the fan may operate after
the vehicle has been switched off, even if
the en
gine is cold.
In addition, as the cooling system is pressurised, wait at least one hour after switching off the engine before carrying out any
work.
To avoid any risk of scalding, unscrew the cap
by two turns to allow the pressure to drop.
When the pressure has dropped, remove the
cap and top up the level.