check engine Citroen DS3 2015 1.G User Guide

DS3_en_Chap08_info-pratiques_ed01-2015
Fuel tankFuel tank capacity: approximately 50 litres (petrol) or 46 litres (diesel) or 33 litres (LPg) ;
(dep ending on version: approximately 30 litres (petrol or di esel)).
Low fuel level
Filling
A label affixed to the inside of the flap reminds you   of   the   type   of   fuel   to   be   used   depending   on  
y

our
 eng
ine.
Additions
  of   fuel   must   be   of   at   least   7   litres,   in  
o

rder   to   be   registered   by   the   fuel   gauge.The
  key   cannot   be   removed   from   the  
l

ock   until   the   cap   is   refitted.
Opening
  the   filler   cap   may   create   a  
n

oise   caused   by   an   inrush   of   air.   This  
v

acuum   is   entirely   normal,   resulting  
f

rom   the   sealing   of   the   fuel   system.
To
  fill   the   tank   safely:
F

t
he engine must be switched off,
F

o
pen the fuel filler flap,
F
 
i
nsert   the   key   in   the   cap,   then   turn   it   to   the  
l

eft,F
 r emove   the   cap   and   hook   it   onto   the   clip  
l

ocated on the inside of the flap,
F
 
f
ill   the   tank,   but do not continue after the
3rd cut- off of the pump ;
  this   could   cause  
m

alfunctions.
When
  you   have   filled   the   tank:
F
 
p
ut   the   cap   back   in   place,
F
 
t
urn   the   key   to   the   right,   then   remove   it  
f

rom   the   cap,
F
 
c
lose   the   flap.
When the fuel tank minimum level is reached   this   warning   lamp   comes   on o

n   the   instrument   panel.   When   it   first
 c

omes   on   there   remains   approximately
5 litres
  of   fuel   in   the   tank.
With Stop & Start, never refuel with the
system  in   STOP   mode;   you   must   switch  
o

ff   the   ignition   with   the   key.
You
 
must   refuel   as   soon   as   possible   to   avoid  
r

unning   out   of   fuel.
If
 
you
 
run   out   of   fuel   (Diesel),   refer   also   to   the  
"

Checks"
 s
ection.

DS3_en_Chap08_info-pratiques_ed01-2015
* According to country of sale.
Misfuel prevention (Diesel)*Mechanical device which prevents filling the tank of a Diesel vehicle with petrol. It avoids the risk of engine damage that can result from filling with the wrong   fuel.
Located
  in   the   filler   neck,   the   misfuel   prevention   device   appears   when   the   filler   cap   is   removed.
Operation
When a petrol filler nozzle is introduced into the
fuel  filler   neck   of   your   Diesel   vehicle,   it   comes  
i

nto   contact   with   the   flap.   The   system   remains  
c

losed   and   prevents   filling.
do n

ot persist but introduce a d
i
esel type
filler nozzle. It
  remains   possible   to   use   a   fuel   can   to  
f

ill   the   tank.
In   order   to   ensure   a   good   flow   of   fuel,  
d

o not place the nozzle of the fuel can
in direct contact with the flap of the
misfuel   prevention   device   and   pour  
s

l ow l y.
Travelling abroad
As Diesel fuel pump nozzles may b
e different in other countries, the
presence
  of   the   misfuel   prevention  
d

evice   may   make   refuelling   impossible.
Before
  travelling   abroad,   we  
r

ecommend   that   you   check   with   the  
C

ITROËN   dealer   network,   whether  
y

our vehicle is suitable for the fuel
pumps
  in   the   country   in   which   you   want  
t

o   travel.

191
DS3_en_Chap08_info-pratiques_ed01-2015
In the event of a fault with the the SCR emissions control system
If it is a temporary fault, the alert disappears   during   the   next   journey,  
a

fter   self-diagnosis   of   the   SCR   system.
A
  system   that   prevents   engine   starting   is   activated   automatically   from   650   miles   (1   100   km)   after   confirmation   of   a   fault   with   the   SCR   emissions  
c

ontrol   system.   Have   the   system   checked   by   a   CITROËN   dealer   or   a   qualified   workshop   as   soon   as   possible.
In the event of the detection of a fault
du
ring an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)
The
 
UREA,   SERVICE   and   diagnostic   warning  
l

amps
  comes   on,   accompanied   by   an   audible  
s

ignal
  and   the   display   of   the   message  
"

Emissions
 f
ault".
The
 
alert   is   triggered   when   driving   when   the  
f

ault
 
is   detected   for   the   first   time,   then   when  
s

witching   on   the   ignition   for   subsequent  
j

ourneys,   while   the   fault   persists. If   a   fault   with   the   SCR   system   is   confirmed   (after
 3

0   miles   (50   km)   covered   with   the   permanent
 d

isplay   of   the   message   signalling   a   fault),   the
 S

ERVICE   and   engine   diagnostic   warning   lamps
 c

ome   on   and   the   UREA   warning   lamp   flashes,
 a

ccompanied   by   an   audible   signal   and   the
 d

isplay   of   a   message   (e.g.:   "Emissions   fault:
 S

tarting   prevented   in   150   miles")   indicating   the
 r

emaining   range   express   in   miles   or   kilometres.
While   driving,   the   message   is   displayed   every
 3

0   seconds   while   the   fault   with   the   SCR   system
 p
ersists.
The   alert   is   repeated   when   switching   on   the ig

nition.
You
  should   go   to   a   CITROËN   dealer   or   a
 q

ualified   workshop   as   soon   as   possible.
Other wise, you will not be able to restart your
engine. You
  have   exceeded   the   authorised  
d

riving   limit:   the   starting   prevention  
s

ystem   inhibits   engine   starting.
Every 
time  the  ignition  is  switched  on,  the  SERVICE a
nd   engine   diagnostic   warning   lamps   come   on   and t

he   UREA   warning   lamp   flashes,   accompanied   by
 a

n   audible   signal   and   the   display   of   the   message
 "

Emissions   fault:   Starting   prevented".
Starting prevented
To
  be   able   to   start   the   engine,   you   must   call   on  
a

  CITROËN   dealer   or   a   qualified   workshop.
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
When the battery on your vehicle is discharged, the   engine   can   be   started   using   a   slave   battery  
(

external   or   on   another   vehicle)   and   jump   leads.
Starting using another
battery
First check that the slave battery has a nominal voltage   of   12   V   and   a   capacity   at   least   equal   to  
t

hat   of   the   discharged   battery.
Do
  not   try   to   start   the   engine   by   connecting   a  
b

attery   charger.
Do
  not   disconnect   the   (+)   terminal   when   the  
e

ngine   is   running.
F

C
onnect the red cable to the positive
terminal
  (+)   of   the   flat   battery   A, then to the
positive
  terminal   (+)   of   the   slave   battery   B.
F
 
C
onnect   one   end   of   the   green   or   black  
c

able   to   the   negative   terminal   (-)   of   the  
s

lave battery B   (or   earth   point   on   the   other  
v

ehicle).
F
 
C
onnect  
t
he  
o
ther  
e
nd  
o
f  
t
he  
g
reen  
o
r  
b
lack  
c

able   to   the   negative   terminal   C
(or
  the   engine   mounting)   of   the   broken-
down
  vehicle. F
 
S
tart   the   engine   of   the   other   vehicle   and  
a

llow   it   to   run   for   a   few   minutes.
F
 
O
perate   the   starter   of   the   broken-down  
v

ehicle   and   let   the   engine   run.
 I

f   the   engine   does   not   start   immediately,  
s

witch   off   the   ignition   and   wait   a   few  
m

oments   before   trying   again.
F
 
W
ait   until   the   engine   returns   to   idle,   then  
d

isconnect   the   jump   leads   in   reverse   order.Some
  functions   are   not   available   if   the  
b

attery   is   not   sufficiently   charged.

225
DS3_en_Chap08_info-pratiques_ed01-2015
Protect your eyes and face before
handling  the   battery.
All
  operations   on   the   battery   must   be  
c

arried out in a well ventilated area
away
  from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   and   fire.
Do
  not   try   to   charge   a   frozen   battery;  
t

he   battery   must   first   be   thawed   out   to  
a

void  
t
he  
r
isk  
o
f  
e
xplosion.  
I
f  
t
he  
b
attery  
h

as   been   frozen,   before   charging   have  
i

t   checked   by   a   CITROËN   dealer   or  
a

  qualified   workshop   who   will   check  
t

hat   the   internal   components   have   not  
b

een   damaged   and   the   casing   is   not  
c

racked,   which   could   cause   a   leak   of  
t

oxic   and   corrosive   acid.
Do not reverse the polarity and use
only
  a   12   V   charger.
Do
  not   disconnect   the   terminals   while  
t

he   engine   is   running.
Do
  not   charge   the   batteries   without  
d

isconnecting   the   terminals   first.
Wash
  your   hands   after wards.
Do not push the vehicle to start the
engine
 
if
 
you
 
have
 
an
 
electronic
 
or
 
a

utomatic
 
gearbox.Charging the battery using
a battery charger
Batteries contain harmful substances such a s   sulphuric   acid   and   lead.   They   must   be d

isposed   of   in   accordance   with   regulations
 a

nd   must   not,   in   any   circumstances,   be
 d

iscarded   with   household   waste.
Take
  used   remote   control   batteries   and
 v

ehicle batteries to a special collection
point.
F Follow the instructions for use provided by the   manufacturer   of   the   charger.
Do
  not   disconnect   the   battery   to   charge   it.
Practical information

231
DS3_en_Chap08_info-pratiques_ed01-2015
Towing with the RACIng version
Your vehicle cannot be fitted with a
towbar.
  The   space   occupied   by   the  
s

port   diffuser   prevents   this.
Side wind
F Take  into   account   the   increased   sensitivity  t
o   side   wind.
Cooling
Towing a trailer on a slope increases the temperature   of   the   coolant.
As
  the   fan   is   electrically   controlled,   its   cooling  
c

apacity   is   not   dependent   on   the   engine   speed.
F
 
T
o   lower   the   engine   speed,   reduce   your  
s

peed.
The
  maximum   towed   load   on   a   long   incline  
d

epends   on   the   gradient   and   the   ambient  
t

emperature.
In
  all   cases,   keep   a   check   on   the   coolant  
t

emperature. F
 
I
f   the   warning   lamp   and   the  
S

TOP
 
warning   lamp   come   on,  
s

top the vehicle and switch off
the
  engine   as   soon   as   possible.
Braking
Towing a trailer increases the braking distance.
T o   avoid   overheating   of   the   brakes   on   a   long  
m

ountain   type   of   descent,   the   use   of   engine  
b

raking   is   recommended.
Ty r e s
F Check   the   tyre   pressures   of   the   towing  v
ehicle   and   of   the   trailer,   observing   the  
re

commended
 p
ressures.
Lighting
F Check  the   electrical   lighting   and   signalling  o
n   the   trailer.
The
  rear   parking   sensors   will   be  
d

eactivated   automatically   if   a   genuine  
C

ITROËN   towbar   is   used.
Practical information

239
DS3_en_Chap09_verifications_ed01-2015
Bonnet
Opening
F Open  the   front   left   door.
F P ull the interior release lever A , located at
the
  bottom   of   the   door   aperture.F
 
P
ush   the   exterior   safety   catch   B to the left
and   raise   the   bonnet.
Before   doing   anything   under   the  
b

onnet, switch off the Stop & Start
system   to   avoid   any   risk   of   injury  
r

esulting   from   an   automatic   change   to  
S

TART   mode.
The location of the interior release lever
prevents   opening   of   the   bonnet   while  
t

he   front   left   door   is   closed.F

U
nclip the bonnet stay C   from   its   housing,  
h

olding   it   by   its   foam   protection.
F
 
F
ix   the   stay   in   the   notch   to   hold   the   bonnet  
ope

n.
Closing
F Take  the   stay   out   of   the   support   notch.
F  C lip   the   stay   in   its   housing.
F

L
ower the bonnet and release it at the end
of
  its   travel.
F
 
P
ull   on   the   bonnet   to   check   that   it   is   fully  
l

atched.When
  the   engine   is   hot,   handle   the  
e

xterior   safety   catch   and   the   stay   with  
c

are.
To
  avoid   damaging   the   electric   units,  
t

he   use   of   a   high   pressure   jet   wash  
u

nder   the   bonnet   is   strictly   prohibited.
Checks

241
DS3_en_Chap09_verifications_ed01-2015
Diesel engines
1. Screenwash  fluid   reservoir.
2. C oolant   header   tank.
3.
 A

ir   filter.
4.
 B

rake   fluid   reservoir.
5.
 B

attery.
6.
 F

usebox.
7.
 E

ngine   oil   dipstick.
8.
 E

ngine   oil   filler   cap.
9.
 P

riming   pump   (on   fuel   filter).
Checks

Checking levels
Check all of these levels regularly, in line with the manufacturer's service schedule. Top them up if necessary, unless other wise indicated.
I f   a   level   drops   significantly,   have   the   corresponding   system   checked   by   a   CITROËN   dealer   or   a   qualified   workshop.
Engine oil level
It is normal to top up the oil level between two   services   (or   oil   changes).   CITROËN  
r

ecommends   that   you   check   the   level,   and   top  
u

p   if   necessary,   every   3   000   miles   (5   000   kms).
The
  check   is   carried   out   either   when  
t

he   ignition   is   switched   on   using   the  
o

il   level   indicator   in   the   instrument  
p

anel   for   vehicles   so   equipped,   or  
u

sing   the   dipstick.
To   ensure   that   the   reading   is   correct,  
y

our   vehicle   must   be   parked   on   a   level  
s

ur face   with   the   engine   having   been   off  
f

or   more   than   30   minutes.
Take   care   when   working   under   the  
b

onnet,   as   certain   areas   of   the   engine  
m

ay   be   extremely   hot   (risk   of   burns)  
a

nd   the   cooling   fan   could   start   at   any  
t

ime   (even   with   the   ignition   off).
Checking using the dipstick
A = MA X
B   =   MIN If you find that the level is above the A
  mark   or  
belo

w the B   mark,   do not star t the engine
.
-
I
f the level is above the MAX
 
mark   (risk  
o

f   damage   to   the   engine),   contact   a  
C

ITROËN   dealer   or   a   qualified   workshop.
-
I
f the level is below the MI n
  mark,   you  
m

ust   top   up   the   engine   oil.
Refer
 
to
 
the
 
"Petrol   engine"   or   "Diesel   engine"  
s

ection
 
for
 
the   location   of   the   dipstick   in   the  
e

ngine
 
compartment   of   your   vehicle.
F
 
T

ake
 
the
  dipstick   by   its   coloured   grip   and  
r

emove
 
it   completely.
F
 
W

ipe
 
the
  end   of   the   dipstick   using   a   clean  
n

on-fluffy   cloth.
F
 
R

efit
 
the
  dipstick   and   push   fully   down,   then  
p

ull
 
it
 
out   again   to   make   the   visual   check:  
t

he
 
correct   level   is   between   the   marks   A
and B .
Oil grade
Before topping-up the oil or changing the oil, c
heck   that   the   oil   is   the   correct   grade   for   your  
e

ngine   and   conforms   to   the   manufacturer's  
r

ecommendations.

243
DS3_en_Chap09_verifications_ed01-2015
Brake fluid level
Changing the fluid
Refer to the manufacturer's service schedule for   details   of   the   interval   for   this   operation.
Fluid specification
The brake fluid must conform to the manufacturer's r ecommendations.
The
  brake   fluid   level   should   be   close  
t

o   the   "MA X"   mark.   If   it   is   not,   check  
t

he   brake   pad   wear.
After
 
topping
 
up
 
the
 
oil,
 
the
 
check
 
when
 
s

witching
 
on
 
the
 
ignition
 
with
 
the
 
oil
 
level
 
i

ndicator
 
in
 
the
 
instrument
 
panel
 
is
 
not
 
valid
 
d

uring
 
the
 
30
 
minutes
 
after
 
topping
 
up.
Topping up the engine oil level
Refer to the "Petrol engine" or "Diesel engine" s ection for the location of the oil filler cap in the
engine
  compartment   of   your   vehicle.
F

U
nscrew the oil filler cap to reveal the filler
aperture.
F
 
A
dd   oil   in   small   quantities,   avoiding   any  
s

pills   on   engine   components   (risk   of   fire).
F
 
W
ait   a   few   minutes   before   checking   the  
l

evel   again   using   the   dipstick.
F
 
A
dd   more   oil   if   necessary.
F
 
A
fter   checking   the   level,   carefully   refit   the  
o

il   filler   cap   and   the   dipstick   in   its   tube.
Engine oil change
Refer to the manufacturer's service schedule for   details   of   the   interval   for   this   operation.
In
  order   to   maintain   the   reliability   of   the   engine  
a

nd   emission   control   system,   never   use  
a

dditives   in   the   engine   oil.
Checks