heating Citroen DS3 2015 1.G Owner's Manual

DS3_en_Chap01_controle-de-marche_ed01-2015
Warning/indicator lampis on Cause Action / Observations
di

esel engine
pre-heating fixed.
The
  key   is   at   position   2   (ignition   on)   in  
t

he   ignition   switch.Wait
  until   the   warning   lamp   goes   off   before   starting.
The
  period   of   illumination   of   the   warning   lamp   is  
d

etermined   by   the   climatic   conditions   (up   to   about  
t

hirty   seconds   in   extreme   climatic   conditions).
If
  the   engine   does   not   start,   switch   the   ignition   off   and  
t

hen   on,   wait   until   the   warning   lamp   goes   off   again,  
t

hen   start   the   engine.
Parking brake fixed. The
  parking   brake   is   applied   or   not  
p

roperly
 r
eleased.Release
  the   parking   brake   to   switch   off   the   warning  
l

amp,   keeping   your   foot   on   the   brake   pedal.
Observe
  the   safety   recommendations.
For
  more   information   on   the   parking   brake,   refer   to   the  
c

orresponding
 s
ection.
Stop & Star t fixed. When
  the   vehicle   stops   (red   lights,
 t

raffic   jams,   ...)   the   Stop   &   Start   system
 h

as   put   the   engine   into   STOP   mode.The
  warning   lamp   goes   off   and   the   engine   restarts  
a

utomatically   in   START   mode,   as   soon   as   you   want   to  
m

ove   off.
flashes for a few
seconds,
  then   goes  
o

f f.STOP
  mode   is   temporarily  
u

navailable.
or
START
  mode   is   invoked  
au

tomatically.For
  more   information   on   special   cases   with   STOP  
m

ode   and   START   mode,   refer   to   the   "Stop   &   Start"  
s

ection.

73
DS3_en_Chap03_confort_ed01-2015
Additional adjustments
Head restraint height adjustment
F To  raise   the   head   restraint,   pull   it   upwards.
F  T o   remove   the   head   restraint,   press   the  
l

ug   A   and   pull   the   head   restraint   upwards.
F
 
T
o   put   the   head   restraint   back   in   place,  
e

ngage   the   head   restraint   stems   in   the  
o

penings   keeping   them   in   line   with   the   seat  
b

ack.
F
 
T
o   lower   the   head   restraint,   press   the   lug   A
and
  the   head   restraint   at   the   same   time.The
  head   restraint   is   fitted   with   a   frame  w
ith   notches   which   prevents   it   from  
l

owering;   this   is   a   safety   device   in   case  
o

f   impact.
The adjustment is correct when the
upper edge of the head restraint is
level with the top of the head.
Never drive with the head restraints
removed;
  they   must   be   in   place   and  
adj

usted
 c
orrectly.
Heated seats control
With the engine running, the front seats can be heated s eparately.
F
 
U
se   the   adjustment   dial,   placed   on   the   side  
o

f each front seat, to switch on and select
the
  level   of   heating   required:
0:

  Off.
1:

  Low.
2:

  Medium.
3:

  High.
Comfort

81
DS3_en_Chap03_confort_ed01-2015
Ventilation
Air intake
The air circulating in the passenger compartment is   filtered   and   originates   either   from   the   outside   via t

he   grille   located   at   the   base   of   the   windscreen   or
 f

rom   the   inside   in   air   recirculation   mode.
Air treatment
The incoming air follows various routes depending   on   the   controls   selected   by   the  
d

river:
-
 
d
irect   arrival   in   the   passenger  
c

ompartment   (air   intake),
-
 
p
assage   through   a   heating   circuit   (heating),
-
 
p
assage   through   a   cooling   circuit   (air  
c

onditioning).
The
  temperature   control   enables   you   to   obtain  
t

he   level   of   comfort   required   by   mixing   the   air   of  
t

he   various   circuits.
The air distribution control enables you to
diffuse
  the   air   in   the   passenger   compartment  
c

ombining   several   air   vents.
The air flow control enables you to increase or
reduce
  the   speed   of   the   ventilation   blower.
Control panel
The controls of this system are grouped together   on   control   panel   A on the centre
console.
  Depending   on   the   model,   the  
f

unctions   offered   are:
-
 
t
he   level   of   comfort   required,
-

a
ir flow,
-
a

ir distribution,
-
 d

emisting-defrosting,
-
 
m
anual   or   digital   air   conditioning   controls.
Air distribution
1. Windscreen demisting-defrosting v ents.
2. F ront   side   window   demisting-defrosting  
ve

nts.
3.
 S

ide   adjustable   air   vents.
4.
 C

entral   adjustable   air   vents.
5.
 A

ir   outlets   to   the   front   footwells.
6.
 A

ir   outlets   to   the   rear   footwells.
Comfort

83
DS3_en_Chap03_confort_ed01-2015
Heating / Ventilation
Manual control panelElectric control panel
Manual air conditioning
Manual control panel Electric control panel
Comfort

DS3_en_Chap03_confort_ed01-2015
The heating / ventilation or air conditioning systems operates with the engine running, as well as in STOP mode with Stop & Start.
1. Temperature adjustment
F Turn  the   dial   from   blue  (
cold)   to   red   (hot)   to   adjust  
t

he   temperature   to   your  
r

equirements.
2. Air flow adjustment
F Turn   the   dial   from   position   1
to position 5 to obtain a
comfortable
  air   flow.
F

I

f you place the air flow control
in position 0
  (deactivation   of   the  
s

ystem),   the   temperature   is   no  
l

onger   maintained   at   a   comfortable  
l

evel.   However,   a   slight   flow   of   air,  
d

ue  
t
o  
t
he  
m
ovement  
o
f  
t
he  
v
ehicle,  
c

an   still   be   felt.
3. Air distribution adjustment
Windscreen and side windows.
W indscreen, side windows and
footwells.
Footwells.
Central
  and   side   vents.
The air distribution can be
adapted
  by   placing   the   dial  
i

n   an   intermediate   position.
4. Air intake / Air recirculation
The intake of exterior air avoids the formation of   mist   on   the   windscreen   and   side   windows.
The recirculation of interior air insulates the
passenger
  compartment   from   exterior   odours  
a

nd   smoke.
Return
  to   exterior   air   intake   as   soon   as   possible  
t

o   prevent   deterioration   of   the   air   quality   and  
t

he   formation   of   mist.
Manual control panel F
 
M
ove   the   manual   control   to  
t

he   left   to   be   in   the   "recycling  
i

nterior   air"   position.
F
 
M
ove   the   manual   control   to   the  
r

ight   to   return   to   the   "fresh   air  
i

ntake"   position.

87
DS3_en_Chap03_confort_ed01-2015
It is possible to adjust one or more functions manually   while   leaving   the   other   functions   in  
a

utomatic   mode.
The "AUTO"
 

symbol   switches   off.
To
  return   to   automatic   mode,   press   the   "AUTO"
button.
Manual override
4. Air conditioning on/off
For maximum cooling or heating of the c abin,   it   is   possible   to   go   beyond   the  
m

inimum   14   or   maximum   28   values.
F

P
ress the blue button 2 until "LO"
is displayed or the red button 2
until
"HI"
 
is   displayed. Press this button to switch off the air
conditioning.
Stopping
  the   air   conditioning   may   cause
 s

ome   problems   (humidity,   misting).
5. Air intake / Air recirculation
Press this button for recirculation of
the
  interior   air.   The   air   recirculation  
s

ymbol
 5
  is   displayed.
Avoid
  prolonged   recirculation   of  
i

nterior   air   (risk   of   condensation   or  
d

eterioration   of   the   air   quality).
Switching
 
to
 
manual
 
mode
 
may
 
not
 
be
 
s

uitable
 
(temperature,
 
humidity,
 
odour,
 
c

ondensation)
 
and
 
does
 
not
 
provide
 
o

ptimum
 c

omfort. Automatic
 
operation
 
of
 
the
 
air
 
conditioning
 
is
 
r

esumed
 
when
 
the
 
button
 
is
 
pressed
 
again.
 

The
 
symbol
 
"A /C "
 

is
 
displayed. Air
 
recirculation   enables   the   passenger  
c

ompartment   to   be   isolated   from   exterior  
o

dours
 
and   smoke.
Press
 
this
  button   again   or   press   the   "AUTO"
button
 
to
 
resume   automatic   management   of  
t

he
 
intake
  of   air.   The   air   recirculation   symbol   5
goes
 
off.
Comfort

89
DS3_en_Chap03_confort_ed01-2015
Front demist - defrost
With the heating /
ventilation system
F Put  the   temperature   and   air   flow   controls   to  t
he   dedicated   marked   position.
F
 
P
ut   the   air   intake   control   to   the   "Exterior   air  
i

ntake"   position  
 
(

manual   control   to   the   right   or   electric  
c

ontrol   with   indicator   lamp   off).
F

P
ut the air distribution control to the
"Windscreen"
 p

osition.
These
  markings   on   the   control   panel   indicate   the   control   positions   for   rapid   demisting   or  
d

efrosting   of   the   windscreen   and   side   windows.
With the manual air
conditioning system
F Put
  the   temperature   and   air   flow   controls   to  t
he   dedicated   marked   position.
F
 
P
ut   the   air   intake   control   to   the   "Exterior   air  
i

ntake"   position  
 
(

manual   control   to   the   right   or   electric  
c

ontrol   with   indicator   lamp   off).
F

P
ut the air distribution control to the
"Windscreen"
 p

osition.
F
 
S
witch   on   the   air   conditioning   by   pressing  
t

he "A /C "
 
button;   the   associated   green  
w

arning   lamp   comes   on.
With
  Stop   &   Start,   when   the   demisting,  
a

ir   conditioning   and   air   flow   functions  
a

re   activated,   STOP   mode   is   not  
a

vailable.
Comfort

DS3_en_Chap03_confort_ed01-2015
Rear screen demist - defrost
The control button is located on the heating or air conditioning system control panel.
Switching on
The rear screen demisting/defrosting can only operate   when   the   engine   is   running.
F
 
P
ress   this   button   to   demist /defrost   the  
r

ear   screen   and   (depending   on   version)  
t

he   door   mirrors.   The   indicator   lamp  
a

ssociated   with   the   button   comes   on.
Switching off
The demisting/defrosting switches off automatically   to   prevent   an   excessive  
c

onsumption   of   current.
F
 
I
t   is   possible   to   stop   the   demisting/
defrosting
  operation   before   it   is   switched  
o

ff   automatically   by   pressing   the   button  
a

gain.   The   indicator   lamp   associated   with  
t

he   button   switches   off. Switch
  off   the   demisting/defrosting  
o

f   the   rear   screen   and   door   mirrors  
a

s   soon   as   appropriate,   as   reducing  e
lectrical   power   consumption   results   in  r
educed f uel c onsumption.
If the engine is switched off before the d
emisting/defrosting   is   switched   off a

utomatically,
 d
emisting/defrosting
 w
ill
 r

esume   next   time   the   engine   is   switched   on.
Scented air
freshener
This diffuses a fragrance in the passenger compartment,   by   means   of   the   adjustment   dial  
a

nd   the   various   fragrance   cartridges   available.
This
  dial   is   located   on   the   dashboard.
It
  allows   you   to   adjust   the   intensity   of   diffusion  
o

f   the   fragrance.
F
 
T
urn   the   dial   to   the   right   to   permit   diffusion  
o

f   the   fragrance.
F

T
urn the dial to the left to stop diffusion of
the
 f

ragrance.
Adjustment dial
Leave the central vents open.
T he intensity of diffusion of the
fragrance
  may   depend   on   the  
v

entilation   or   air   conditioning   settings.

DS3_en_Chap04_conduite_ed01-2015
A few driving recommendations
Observe the driving regulations at all times and remain vigilant whatever the traffic conditions.
P ay   close   attention   to   the   traffic   and   keep   your   hands   on   the   wheel   so   that   you   are   ready   to   react   at  
a

ny   time   to   any   eventuality.
On
  a   long   journey,   a   break   every   two   hours   is   strongly   recommended.
In
  difficult   weather,   drive   smoothly,   anticipate   the   need   to   brake   and   increase   the   distance   from  
o

ther
 v
ehicles.
driving on flooded roads
We strongly advise against driving on flooded roads,   as   this   could   cause   serious   damage  
t

o   the   engine   or   gearbox,   as   well   as   to   the  
e

lectrical   systems   of   your   vehicle.
Important!
Never drive with the parking brake applied   -   Risk   of   overheating   and  
d

amage   to   the   braking   system!
Do
  not   park   or   run   the   engine   when  
s

tationary   in   areas   where   inflammable  
s

ubstances   and   materials   (dry   grass,  
d

ead   leaves...)   might   come   into   contact  
w

ith   the   hot   exhaust   system   -   Risk   of  
f

ire!
Never leave a vehicle unsupervised
with
  the   engine   running.   If   you   have  
t

o   leave   your   vehicle   with   the   engine  
r

unning,   apply   the   parking   brake  
a

nd   put   the   gearbox   into   neutral   or  
p

osition

n or P,
  depending   on   the   type  
o

f   gearbox.
-
 
c

heck
 
that
 
the
 
depth
 
of
 
water
 
does
 
not
 
e

xceed
 
15
 
cm,
 
taking
 
account
 
of
 
waves
 
t

hat
 
might
 
be
 
generated
 
by
 
other
 
users,
-
 
d

eactivate
 
the
 
Stop
 
&
 
Start
 
system,
-

d

rive as slowly as possible without
stalling.
 
In
 
all
 
cases,
 
do
 
not
 
exceed
 
6
 
mph
 
(

10 km/h),
-

d

o not stop and do not switch off the
engine.
If
 
you
 
are
 
obliged
 
to
 
drive
 
through
 
water: On
 
leaving
 
the
 
flooded
 
road,
 
as
 
soon
 
as
 
c

ircumstances
 
allow,
 
make
 
several
 
light
 
brake
 
a

pplications
 
to
 
dry
 
the
 
brake
 
discs
 
and
 
pads.
If in doubt on the state of your vehicle, contact
a
 
CITROËN
 
dealer
 
or
 
a
 
qualified
 
workshop.

DS3_en_Chap04_conduite_ed01-2015
F Apply  the   parking   brake.
F  W ith   a   manual   gearbox:   place   the   lever   in  
n

eutral   and   fully   depress   the   clutch   pedal.
F
 
W
ith   an   electronic   gearbox:   place   the   lever  
a

t position n  and   press   the   brake   pedal  
f

i r m l y.
F
 
W
ith   an   automatic   gearbox:   place   the   lever  
a

t position P   and   press   the   brake   pedal  
f

i r m l y.
F
 
I
nsert   the   key   in   the   ignition   switch;   the  
s

ystem   recognises   the   code.
F
 
U
nlock   the   steering   column   by  
s

imultaneously   turning   the   steering   and   the  
k

ey.
Starting the engine
In some circumstances, you may have to   apply   some   force   to   turn   the   steering  
w

heel   (wheels   on   lock   for   example).In
  wintry   conditions,   the   warning   lamp  
w

ill   stay   on   longer.   When   the   engine   is  
h

ot,   it   does   not   come   on.In   temperate   conditions,   do   not  
w

arm   the   engine   up   with   the   vehicle  
s

tationary,   but   move   off   straight   away  
a

nd   drive   at   moderate   engine   speeds.
If   the   engine   does   not   start   straight  a
way,   switch   the   ignition   off.   Wait   a  
f

ew   moments   before   trying   again.   If  
t

he   engine   does   not   start   after   a   few  
a

ttempts,   do   not   keep   trying:   you   risk  
d

amaging   the   starter   motor   and   the  
e

ngine.   Call   on   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.Never
  leave   the   engine   running   in  
a

n   enclosed   area   without   adequate  
v

entilation:
 in
ternal
 c
ombustion
 e

ngines   emit   toxic   exhaust   gases,  
s

uch   as   carbon   monoxide.   Danger   of  
i

ntoxication   and   death.   In   very   severe  
w

inter   conditions   (temperatures  b
elow -23°C),   it   is   necessary   to   allow  t
he   engine   to   run   for   4   minutes   before  
s

etting   off,   in   order   to   ensure   the  
c

orrect operation and durability of
the
  mechanical   components   of   your  
v

ehicle,   the   engine   and   gearbox.
F
 
W
ith   a   petrol   engine,   operate   the   starter  
m

otor   by   turning   the   key   to   position   3 until
the
  engine   starts,   without   pressing   the  
a

ccelerator   pedal.   Once   the   engine   starts,  
r

elease   the   key.
F
 
W
ith   a   Diesel   engine,   turn   the   key   to  
p

osition 2 ,
  ignition   on,   to   operate   the  
eng

ine
 p
reheating
 s
ystem. Wait
  until   this   warning   lamp   goes   off
 i

n   the   instrument   panel,   then   operate
 t

he   starter   motor   by   turning   the   key   to
 p

osition
3
 
until   the   engine   starts,   without
 p

ressing   the   accelerator   pedal.   Once
 t

he   engine   starts,   release   the   key.