CITROEN DS3 CABRIO DAG 2016 Handbook (in English)

219
DS3_en_Chap08_info-pratiques_ed01-2015
Engine compartment
fusebox
The fusebox is located in the engine compartment   near   the   battery   (left-hand   side).Access to the fuses
F Unclip  the   cover.
F  C hange   the   fuse   (see   corresponding  
par

agraph).
F

W
hen you have finished, close the cover
carefully
  to   ensure   the   sealing   of   the   fuse  
b

ox.
All
 
work
 
on
 
the
 
fuses
 
in
 
the
 
box
 
l

ocated
 
on
 
the
 
battery,
 
must
 
be
 
done
 
b

y
 
a
 
CITROËN
 
dealer
 
or
 
a
 
qualified
 
w

orkshop.
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
Fuse table
Fuse n°R ating Functions
F1 20 AEngine
  control   unit   supply,   cooling   fan   unit   control   relay,   multifunction   engine   control   main   relay,   injection   pump  
(

Diesel).
F2 15 AHorn.
F3 10 AFront
  /   rear   screenwash.
F4 20 ALED
  lamps.
F5 15 ADiesel
  heater   (Diesel),   particle   filter   additive   pump   (Diesel),   air   flow   sensor   (Diesel),   blow-by   heater   and  
e

lectrovalves   (VTi).
F6 10 AABS/DSC
  control   unit,   secondary   stop   switch.
F7 10 AElectric
  power   steering,   automatic   gearbox.
F8 25 AStarter
  control.
F9 10 ASwitching
  and   protection   unit   (Diesel).
F10 30 AFuel
  heater   (Diesel),   blow-by   heater   (Diesel),   fuel   pump   (VTi),   injectors   and   ignition   coils   (petrol).
F11 40 AHeater
 b

lower.

221
DS3_en_Chap08_info-pratiques_ed01-2015
Fuse n°R ating Functions
F12 30 AWindscreen
  wipers   slow   /   fast   speed.
F13 40 ABuilt-in
  systems   inter face   supply   (ignition   positive).
F14 30 AValvetronic
  supply   (VTi).
F15 10 ARight-hand
  main   beam   headlamps.
F16 10 ALeft-hand
  main   beam   headlamps.
F17 15 ALeft-hand
  dipped   beam   headlamps.
F18 15 ARight-hand
  dipped   beam   headlamps.
F19 15 AOxygen
  sensors   and   electrovalves   (VTi),   electrovalves  
(

Diesel),   EGR   electrovalve   (Diesel).
F20 10 APumps,
  electronic   thermostat   (VTi),   timimg   electrovalve  
(

THP),   water   in   fuel   sensor   (Diesel).
F21 5 AFan
  assembly   control   supply,   ABS/DSC,   turbo   pump   (THP).
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
Table of maxi-fuses
Fuse n°R ating Functions
MF1* 60 AFan
  assembly.
MF2* 30 AABS
  /   DSC   pump.
MF3* 30 AABS
  /   DSC   electrovalves.
MF4* 60 ABuilt-in
  Systems   Inter face   (BSI)   supply.
MF5* 60 ABuilt-in
  Systems   Inter face   (BSI)   supply.
MF6* 30 AAdditional
  cooling   fan   unit   (THP).
MF7* 80 ADashboard
 f

usebox.
MF8* -Not
  used.
*
  
T

he   maxi-fuses   provide   additional   protection   for   the   electrical   systems.   All   work   on   the   maxi-fuses   must   be   carried   out   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.

223
DS3_en_Chap08_info-pratiques_ed01-2015
BatteryProcedure for charging your battery when it is flat or for starting the engine using another battery.T he   battery   is   located   under   the   bonnet.
To
  gain   access   to   it:
F
 
o
pen   the   bonnet   using   the   interior   release  
l

ever,   then   the   exterior   safety   catch,
F

s
ecure the bonnet stay,
F
 
l
ift   the   plastic   cover   on   the   (+)   terminal.
Access to the batteryAfter refitting the battery by a CITROËN   dealer   or   a   qualified  
w

orkshop,   the   Stop   &   Start   system  
w

ill only be active after a continuous
period
  of   immobilisation   of   the   vehicle,  
a

  period   which   depends   on   the   climatic  
c

onditions   and   the   state   of   charge   of  
t

he   battery   (up   to   about   8   hours).
The presence of this label, in particular
with
 
the
 
Stop
 
&
 
Start
 
system,
 
indicates
 
t

he use of a 12 V lead-acid battery with
special
 t

echnology
 a

nd
 s

pecification;
 t

he
 
involvement
 
of
 
a
 
CITROËN
 
dealer
 
o

r
 
a
 
qualified
 
workshop
 
is
 
essential
 
w

hen
 
replacing
 
or
 
disconnecting
 
the
 
b

attery.
Failure
 
t

o
 
o

bserve
 
t

his
 
r

ecommendation
 
m

ay
 
cause
 
premature
 
wear
 
of
 
the
 
b

attery.
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
When the battery on your vehicle is discharged, the   engine   can   be   started   using   a   slave   battery  
(

external   or   on   another   vehicle)   and   jump   leads.
Starting using another
battery
First check that the slave battery has a nominal voltage   of   12   V   and   a   capacity   at   least   equal   to  
t

hat   of   the   discharged   battery.
Do
  not   try   to   start   the   engine   by   connecting   a  
b

attery   charger.
Do
  not   disconnect   the   (+)   terminal   when   the  
e

ngine   is   running.
F

C
onnect the red cable to the positive
terminal
  (+)   of   the   flat   battery   A, then to the
positive
  terminal   (+)   of   the   slave   battery   B.
F
 
C
onnect   one   end   of   the   green   or   black  
c

able   to   the   negative   terminal   (-)   of   the  
s

lave battery B   (or   earth   point   on   the   other  
v

ehicle).
F
 
C
onnect  
t
he  
o
ther  
e
nd  
o
f  
t
he  
g
reen  
o
r  
b
lack  
c

able   to   the   negative   terminal   C
(or
  the   engine   mounting)   of   the   broken-
down
  vehicle. F
 
S
tart   the   engine   of   the   other   vehicle   and  
a

llow   it   to   run   for   a   few   minutes.
F
 
O
perate   the   starter   of   the   broken-down  
v

ehicle   and   let   the   engine   run.
 I

f   the   engine   does   not   start   immediately,  
s

witch   off   the   ignition   and   wait   a   few  
m

oments   before   trying   again.
F
 
W
ait   until   the   engine   returns   to   idle,   then  
d

isconnect   the   jump   leads   in   reverse   order.Some
  functions   are   not   available   if   the  
b

attery   is   not   sufficiently   charged.

225
DS3_en_Chap08_info-pratiques_ed01-2015
Protect your eyes and face before
handling  the   battery.
All
  operations   on   the   battery   must   be  
c

arried out in a well ventilated area
away
  from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   and   fire.
Do
  not   try   to   charge   a   frozen   battery;  
t

he   battery   must   first   be   thawed   out   to  
a

void  
t
he  
r
isk  
o
f  
e
xplosion.  
I
f  
t
he  
b
attery  
h

as   been   frozen,   before   charging   have  
i

t   checked   by   a   CITROËN   dealer   or  
a

  qualified   workshop   who   will   check  
t

hat   the   internal   components   have   not  
b

een   damaged   and   the   casing   is   not  
c

racked,   which   could   cause   a   leak   of  
t

oxic   and   corrosive   acid.
Do not reverse the polarity and use
only
  a   12   V   charger.
Do
  not   disconnect   the   terminals   while  
t

he   engine   is   running.
Do
  not   charge   the   batteries   without  
d

isconnecting   the   terminals   first.
Wash
  your   hands   after wards.
Do not push the vehicle to start the
engine
 
if
 
you
 
have
 
an
 
electronic
 
or
 
a

utomatic
 
gearbox.Charging the battery using
a battery charger
Batteries contain harmful substances such a s   sulphuric   acid   and   lead.   They   must   be d

isposed   of   in   accordance   with   regulations
 a

nd   must   not,   in   any   circumstances,   be
 d

iscarded   with   household   waste.
Take
  used   remote   control   batteries   and
 v

ehicle batteries to a special collection
point.
F Follow the instructions for use provided by the   manufacturer   of   the   charger.
Do
  not   disconnect   the   battery   to   charge   it.
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
Load reduction modeSystem which manages the use of certain functions   according   to   the   level   of   charge  
r

emaining   in   the   battery.
When
  the   vehicle   is   being   driven,   the   load  
r

eduction   function   temporarily   deactivates  
c

ertain   functions,   such   as   the   air   conditioning,  
t

he   heated   rear   screen...
The deactivated functions are reactivated
automatically
  as   soon   as   conditions   permit.Energy economy modeSystem which manages the period of use of certain functions to conserve a sufficient level of c
harge   in   the   battery.
After
  the   engine   has   stopped,   you   can   still   use   functions   such   as   the   audio   equipment,   windscreen  
w

ipers,   dipped   beam   headlamps,   courtesy   lamps,   etc.   for   a   maximum   combined   period   of  
t

hirty minutes. This
  period   may   be   greatly   reduced   if  
t

he   battery   is   not   fully   charged.
A
  flat   battery   prevents   the   engine   from  
s

tarting.
If
  the   telephone   is   being   used   at   the  
s

ame   time,   it   will   be   interrupted   after  
10
 m

inutes.
Switching to economy mode
Once this period has elapsed, a message appears   in   the   screen   indicating   that   the  
v

ehicle   has   switched   to   economy   mode   and   the  
a

ctive   functions   are   put   on   standby.
Exiting economy mode
These functions are reactivated automatically the   next   time   the   vehicle   is   driven.
F
 
I
n   order   to   resume   the   use   of   these  
f

unctions   immediately,   start   the   engine   and  
l

et   it   run   for   a   few   minutes.
The
  time   available   to   you   will   then   be   double  
t

he   period   for   which   the   engine   is   left   running.  
H

owever, this period will always be between
five
  and   thirty   minutes.

227
DS3_en_Chap08_info-pratiques_ed01-2015
Changing a front or rear wiper bladeProcedure for replacing a worn wiper blade with a new one without the use of tools.
Before removing a front
wiper blade
F Within  one   minute   after   switching   off   the  i
gnition,   operate   the   wiper   stalk   to   position  
t

he   wiper   blades   in   the   vertical   position.
This
  position   must   be   used   in   order   to   avoid  
d

amaging   the   wiper   blade   and   the   bonnet.
Removal
F Raise  the   corresponding   wiper   arm.
F  U nclip   the   wiper   blade   and   remove   it.
Fitting
F At  the   front,   check   the   size   of   the   wiper  b
lade as the shorter blade is fitted to the
passenger
  side   of   the   vehicle.
F
 
P
ut   the   corresponding   new   wiper   blade   in  
p

lace   and   clip   it.
F
 
F
old   down   the   wiper   arm   carefully.
After fitting a front wiper
blade
F Switch  on   the   ignition.
F  O perate   the   wiper   stalk   again   to   park   the  
w

iper   blades.
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
Towing the vehicleProcedure for having your vehicle towed or for towing another vehicle using a removable towing eye.
T he   towing   eye   is   installed   in   the   boot   under  
t

he   floor.
To
  gain   access   to   it:
F

o
pen the boot,
F

r
aise the floor,
F
 
r
emove   the   polystyrene   storage   box,
F
 
r
emove   the   towing   eye   from   the   holder.
Access to the tools
ge
neral recommendations
Observe the legislation in force in your country.
E nsure   that   the   weight   of   the   towing   vehicle   is   higher   than   that   of   the   towed   vehicle.
The
  driver   must   remain   at   the   wheel   of   the   towed   vehicle   and   must   have   a   valid   driving   licence.
When
  towing   a   vehicle   with   all   four   wheels   on   the   ground,   always   use   an   approved   towing  
a

rm;   rope   and   straps   are   prohibited.
The
  towing   vehicle   must   move   off   gently.
When
  towing   a   vehicle   with   the   engine   off,   there   is   no   longer   any   power   assistance   for  
b

raking   or   steering.
In
  the   following   cases,   you   must   always   call   on   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or   fast   road,
-
f

our-wheel drive vehicle,
-
 
w
hen   it   is   not   possible   to   put   the   gearbox   into   neutral,   unlock   the   steering,   or   release  
t

he   parking   brake,
-
 
t
owing   with   only   two   wheels   on   the   ground,
-
 
w
here   there   is   no   approved   towing   arm   available...