ABS Citroen DS3 RHD 2013 1.G Owner's Manual

Braking
fixed, associated with
the STOP warninglamp. The brakin
g system fluid level is too low. You must stop as soon as it is safe to do so.
Top up with brake fluid recommended by CITROËN.
If the problem persists, have the system checked by a CITROËN dealer or a qualified workshop.
+

fixed
, associated with
the STOP and ABSwarning lamp. Th
e electronic brake force distribution (EBFD) system has a fault. You must stop as soon as it is safe to do so.
Have it checked by a CITROËN dealer or a qualified
workshop.
Warning lampis onCauseAction / Observations
Anti-lock BrakingSystem (ABS) fixed. The anti-lock braking system has a fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact a
CITROËN dealer or a qualified workshop without delay.
Dynamic stabilitycontrol (ESP/ASR)

flashing. The ESP/ASR regulation is active. The system optimises traction and improves the
directional stability of the vehicle.

fixed, associated with
illumination of the lampin the "ESP OFF"button, accompanied by
an audible signal and a
message in the screen. The E
SP/ASR system has a fault. Have it checked by a CITROËN dealer or a qualified
workshop.

49Monitoring





Monochrome screen C


Information displays
)Press the button, located at the end of
the wiper stalk
, to display the various tripcomputer tabs in succession.- th
e current information tabwith:
●
the range,
●
th
e current fuel consumption,
●
the distance remaining to
be travelled or the Stop &
Start time counter,
- the trip "1"
t
ab with:
●
the distance travelled,
●
the average fuelconsumption,
●
the average speed,for the first trip.
- t
he trip "2"
tab with:
●
the distance travelled,
●
the average fuelconsumption,
●
the average speed,
for the second trip.

)
Pressing the button again returns you to
the normal display.
16/9 colour screen (eMyWay)


Trip zero reset
)
When the trip required is displayed, press
the button on the end of the wiper stalk for more than two seconds.
Trips "1"
and "2"are independent but their useis identical.
For example, trip "1"can be used for daily figures, and trip "2"for monthly figures.

Locking the vehicle
with exterior
perimeter
protection only
To be effective, this deactivation mustbe carried out each time the ignition is switched off.

If the indicator lamp in button Aflashes rapidly, this indicates that the alarmwas triggered during your absence. When the ignition is switched on, thisflashing stops immediately.
To a v o i d t r iggering the alarm when washing your vehicle, lock it using the key in the driver's door lock.
Deactivation of the interior volumetric protection
)Switch off the ignition.)Within ten seconds, press button Auntil
the indicator lamp is on continuously.
)Get out of the vehicle.)Lock or deadlock the vehicle without delay using the locking button on the remote control.
The exterior perimeter protection alone remains
activated; the indicator lamp in button A flashes
once per second.

Reactivation of the interior volumetric protection
)
Unlock the vehicle using the unlockingbutton on the remote control. )
Relock the vehicle using the remotecontrol.
The alarm is activated again with both types
of protection; the indicator lamp in button A
flashes once per second.



Tr iggering of the alarm


This is indicated by sounding of the siren
and flashing of the direction indicators for
approximately thirty seconds.
After it has been triggered, both types of protection are again operational.
If the alarm is triggered ten times in succession, the eleventh time will result in it
becoming inactive.

Braking assistance systems
Group of supplementary systems which helpyou to obtain optimum braking in complete safety in emergency situations:
- anti-lock braking system (ABS),
- electronic brake force distribution (EBFD),
- emergency braking assistance (EBA).

Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the stability and
manoeuvrability of your vehicle when braking,
in par ticular on poor or slippery surfaces.
Activation
The anti-lock braking system comes into
operation automatically when there is a risk of
wheel lock.
Normal operation of the ABS may make itself
felt by slight vibration of the brake pedal.
When braking in an emergency, pressvery firmly without releasing thepressure.


Operating fault
If this warning lamp comes on,
together with the STOPand ABSwarning lamps, accompanied by an
audible signal and a message in the screen, it
indicates a malfunction of the electronic brake force distribution which could result in loss of control of the vehicle when braking.You must stop as soon as it is safe to do so.

When replacing wheels (tyres andrims), ensure that they conform to themanufacturer's recommendations.
If this warnin
g lamp comes on,
accompanied by an audible signaland a message in the screen, it
indicates a malfunction of the anti-lock brakingsystem which could result in loss of control of
the vehicle when braking.
In either case, contact a CITROËN dealer or a
qualified workshop.

219Practical information
Changing main beam headlamp
bulbs
)Remove the protective cover by pulling on
th
e tab. )Disconnect the bulb connector. )Spread the springs to release the bulb.)Remove the bulb and change it.
To r efit, carry out these operations in reverseorder.
Changing sidelamp bulbs
)
Remove the protective cover by pulling on
the tab.
) Pull the bulb holder pressing on the tabs on both sides. )
Pull the bulb and change it.
To r efit, carry out these operations in reverse order.

Changing integrated directionindicator side repeaters
)
Insert a screwdriver towards the centre of
the repeater between the repeater and the
base of the door mirror.) Tilt the screwdriver to extract the repeater and remove it. )
Disconnect the repeater connector.)
Replace the module.
To r efit, carry out these operations in reverse order.
Contact a CITROËN dealer or a qualified workshop to obtain areplacement side repeater module.

221Practical information
1.Brake lamps / sidelamps (P21/5W).2.Sidelamps (P5W).3.Direction indicators (PY21W amber)4.Foglamp, right hand side (PR21W red)Reversing lamp, left hand side (P21W).
Rear lamps
Amber or red bulbs, such as thosefor the direction indicators and rear foglamp, must be replaced by bulbs of the same rating and colour.
Changing bulbs
) Open the boot. )
Remove the access flap from the corresponding side trim panel.)
Unscrew the butterfly nut securing thelamp unit.)
Unclip the lamp unit connector.)
Extract the lamp unit carefully pulling in its
middle towards the outside.
) Spread the four tabs and remove the bulbholder. )
Turn the bulb a quar ter of a turn andchange it.
To r efit, carry out these operations in reverseorder.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.

229Practical information

Fuse table
Fuse N°RatingFunctions
F120 A
Engine control unit supply, cooling fan unit control relay, multifunction engine control main relay, injection pump(Diesel).
F
215 A Horn.
F
310 A Front / rear wash-wipe.
F420 A LED lamps.
F5
15 A Diesel heater (Diesel), particle filter additive pump (Diesel), air flow sensor (Diesel), EGR electrovalve (Diesel),
blow-by heater and electrovalves (VTi).
F
610 A ABS/ESP control unit, secondary stop switch.
F
710 A Electric power steering, automatic gearbox.
F8
25 A Starter control.
F
910 A Switching and protection unit (Diesel).
F10 30 A
Fuel heater
(Diesel), blow-by heater (Diesel), fuel pump (VTi), injectors and ignition coils (petrol).
F1140 A Heater blower.

Fuse N°RatingFunctions
F1230 AWindscreen wipers slow / fast speed.
F1
340 ABuilt-in systems inter face supply (ignition positive).
F1
430 AValvetronic supply (VTi).
F1
510 ARight-hand main beam headlamps.
F16 10 ALe
ft-hand main beam headlamps.
F1715 ALeft-hand dipped beam headlamps.
F18 15
ARight-hand dipped beam headlamps.
F1
915 AOxygen sensors and electrovalves (VTi), electrovalves
(Diesel), EGR electrovalve (Diesel).
F20 10 APumps, electronic thermostat
(VTi), timimg electrovalve (THP), water in fuel sensor (Diesel).
F2
15 AFan assembly control supply, ABS/ESP, turbo pump (THP).

231Practical information

Table of maxi-fuses
Fuse N°RatingFunctions
MF1*60 A Fan assembly.
MF2* 30 A
ABS / ESP pump.
MF3 * 30 A
ABS / ESP electrovalves.
MF4 * 60 A
Built-in Systems Interface (BSI) supply.
MF5 *60 A
Built-in Systems Interface (BSI) supply.
MF6 * 30 A
Additional cooling fan unit (THP).
MF7 * 80
A
Dashboard fusebox.
MF8 *-
Not used.

*

The maxi-fuses provide additional protection for the electrical s
ystems. All work on the maxi-fuses must be carried out by a CITROËN dealer or a qualified workshop.

)On the front bumper, unclip the cover by pressing at the bottom. )Screw the towing eye in fully. )Install the towing bar.)Place the gear lever in neutral (position Nfor an electronic or automatic gearbox).
)On the rear bumper, unclip the cover by pressing at the bottom. )Screw the towing eye in fully. )Install the towing bar. )Switch on the hazard warning lamps on both vehicles.)Move off gently and drive for a shor t
distance only.
Towing your vehicle Towing another vehicle
Failure to obser ve this special conditioncould result in damage to cer taincomponents (braking, transmission...)and the absence of braking assistancethe next time the engine is started.
)
Unlock the steering by turning the key one
notch in the ignition switch and release the
parking brake.) Switch on the hazard warning lamps onboth vehicles. )
Move off gently and drive for a shor t
distance only.