battery Citroen DS4 DAG 2010.5 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2010.5, Model line: DS4 DAG, Model: Citroen DS4 DAG 2010.5 1.GPages: 342, PDF Size: 10.62 MB
Page 6 of 342
41Monitoring
Warning lampis onCauseAction/Obser vations
Batter y charge fixed. The battery charging circuit has a fault (dir ty or loose terminals, slack or cut alternator belt, ...).
The warning lamp should go off when the engine is star ted. If it does not go off, contact a CITROËN dealer or a qualified workshop.
Braking
fixed, associated with the STOP warning lamp.
The braking system fluid level has dropped significantly. You must stop as soon as it is safe to do so. Top up with brake fluid recommended by CITROËN. If the problem persists, have the system checked by a CITROËN dealer or a qualified workshop.
+
fixed, associated with the electric parking brake fault warning lamp, if the parking brake is released.
The braking system has a fault. You must stop as soon as it is safe to do so. Park, switch off the ignition and contact a CITROËN dealer or a qualified workshop.
+
fixed, associated with the STOP and ABS warning lamps.
The electronic brake force distribution (EBFD) system has a fault. You must stop as soon as it is safe to do so. Have it checked by a CITROËN dealer or a qualified workshop.
Page 8 of 342
43Monitoring
Ser vice
temporarily, accompanied by a message.
A minor fault has occurred for which there is no specific warning lamp. Identify the fault by reading the message shown on the screen, such as, for example: - the opening of the doors, boot or bonnet, - the engine oil level, - the remote control battery,
- the tyre pressures, - saturation of the par ticle emission filter on Diesel vehicles (see "Checks - § Checks/Par ticle emissions filter"). For any other faults, contact a CITROËN dealer or a qualified workshop.
fixed, accompanied by a message and an audible signal.
A major fault has occurred for which there is no specific warning lamp. Identify the fault by reading the message shown on the screen and contact a CITROËN dealer or a qualified workshop.
Warning lampis onCauseAction/Obser vations
Par ticle emissions filter (Diesel)
fixed, accompanied by an audible signal
message on the risk of blockage of the par ticle emissions filter.
This indicates that the par ticle emissions filter is star ting to become
saturated.
As soon as driving conditions allow, regenerate the filter by driving at a speed of at least 35 mph (60 km/h)
until the warning lamp goes off.
fixed, accompanied by an audible signal and and a message that the
particle emissions filter additive level is too low.
This indicates the low level of the additive reser voir. Have the reser voir topped up as soon as possible by a CITROËN dealer or a qualified workshop.
Page 19 of 342
A few seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be weighted by the time factor, depending on the type of driving. Therefore, the spanner may also come on if you have exceeded the two year ser vice inter val.
Service indicator zero reset
After each ser vice, the ser vice indicator must be reset to zero. The procedure for resetting to zero is as follows: switch off the ignition, press and hold the ".../000" trip distance recorder zero reset button, switch on the ignition; the distance recorder display begins a countdown, when the screen indicates "=/0" and the spanner disappears, release the button.
This operation cannot be carried out while a reminder of the ser vicing information is being displayed. Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be registered.
Recalling the service information
You can recall the ser vice information at any time. Briefly press the ".../000" trip distance recorder zero reset button. The ser vice information is displayed for a few seconds, in the total distance recorder line or in the instrument panel central colour screen, according to version.
Service overdue
For a few seconds after the ignition is switched on, the spanner flashes to indicate that the service must be carried out as soon as possible. Example: the ser vice is overdue by 300 miles (300 km). For a few seconds after the ignition is switched
on, the screen indicates:
Page 20 of 342
A few seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be weighted by the time factor, depending on the type of driving. Therefore, the spanner may also come on if you have exceeded the two year ser vice inter val.
Service indicator zero reset
After each ser vice, the ser vice indicator must be reset to zero. The procedure for resetting to zero is as follows: switch off the ignition, press and hold the ".../000" trip distance recorder zero reset button, switch on the ignition; the distance recorder display begins a countdown, when the screen indicates "=/0" and the spanner disappears, release the button.
This operation cannot be carried out while a reminder of the ser vicing information is being displayed. Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be registered.
Recalling the service information
You can recall the ser vice information at any time. Briefly press the ".../000" trip distance recorder zero reset button. The ser vice information is displayed for a few seconds, in the total distance recorder line or in the instrument panel central colour screen, according to version.
Service overdue
For a few seconds after the ignition is switched on, the spanner flashes to indicate that the service must be carried out as soon as possible. Example: the ser vice is overdue by 300 miles (300 km). For a few seconds after the ignition is switched
on, the screen indicates: