Citroen DS5 2012 1.G Owner's Manual

189Practical information
Removing a wheel

Parking the vehicle

Immobilise the vehicle where it does notblock traffic: the ground must be level, stable and not slippery. Apply the parking brake unless it has been programmed to automatic mode, switch off the ignition and engage firstgear *
to block the wheels. Check that the braking warning lamp and the Pwarning lamp in the parkingbrake control lever come on.
The occupants must get out of the vehicle and wait where they are safe.
Never go underneath a vehicle raised using a jack; use an axle stand.
List of operations
)
Depending on equipment, remove the cover from from each of bolts using the tool 3
or removethe hub cap using tool 4
. )
Fit the security socket 5
on the wheelbrace 1
to slacken the security bolt (if fitted).)
Slacken the other bolts (no more than a 1/4 turn) using the wheelbrace 1
only.

*
P
osition R
for the electronic gearbox system; P
for the automatic gearbox.

)Place the jack 2 in contact with one of the
two front A or rear Blocations provided on
the underbody, whichever is closest to the
wheel to be chan
ged.
)Raise the vehicle until there is sufficientspace between the wheel and the ground
to admit the spare (not punctured) wheel easily.)Remove the bolts and store them in a clean place. )Remove the wheel.
) Extend the jack 2
until its base plate is incontact with the ground. Ensure that the centreline of the jack base plate is directlybelow the location Aor B
used.

191Practical information

Fitting a wheel
Fitting the "space-saver"spare wheel
If your vehicle is fitted with alloy wheels, when tightening the bolts on fitting, it is normal to notice that the washersdo not come into contact with the "space-saver" spare wheel. The wheel is secured by the conical surface of each bolt.
After changing a wheel
To c o r r e c t ly store the punctured wheelin the boot ( not in the location of the space-saver wheel ), first remove the central cover. When using the "space-saver" typespare wheel, do not exceed 50 mph(80 km/h). Have the tightening of the bolts and thepressure of the spare wheel checkedby a CITROËN dealer or a qualified
workshop without delay. Have the punctured wheel repaired and refitted to the vehicle as soon as possible.


List of operations
)
Put the wheel in place on the hub. )
Screw in the bolts fully by hand.)Pre-tighten the security bolt using the
wheelbrace 1fitted with the security socket 5.)
Pre-tighten the other bolts using the
wheelbrace 1only.

)Lower the vehicle fully. )Fold the jack 2 and detach it. )
Tighten the security bolt using the
wheelbrace 1 fitted with the securitysocket 5.)
Tighten the other bolts using the
wheelbrace 1 only.)
Refit the bolt covers on each of the bolts or
the hub cap (depending on equipment). ) Store the tools in the box.

193Practical information











Changing a bulb
Front lamps
Model with xenon headlamps
1.Main beam headlamps (H1- 35W).2.Directional dipped/directional
headlamps(D1S-35W).3.Daytime running lamps/sidelamps(light emitting diodes - LEDs).4.Direction indicators (HY21-21W).5.Directional foglamps(H11).
Model with halogen headlamps
1.Main beam headlamps (H1- 55W).2.
Dipped beam headlamps (H7-55W).3.Daytime running lamps/sidelamps
(Light emitting diodes - LEDs).4.Direction indicators (HY21-21W).5.Directional foglamps(H11).
For H7 type bulbs with lugs... take care to observe their correct installation so asto ensure the best lighting performance.

In some weather conditions (e.g. low temperature or humidity), the presence of misting on the internal surface of the glass of the headlamps and rear lampsis normal; it disappears after the lamps have been on for a few minutes.


Risk of electrocution

Xenon bulbs (D1S-35W) must bereplaced by a CITROËN dealer or aqualified workshop.

(xenon model)
) Remove the protective plastic cover by
pulling on the tab.) Remove the connector with the bulb bypressing on the lug at the bottom. )
Remove the bulb and change it.
For reassembly, carry out these operations in reverse order.
The headlamps are fitted withpolycarbonate glass with a protectivecoating:)do not clean them using a dryor abrasive cloth, nor with adetergent or solvent product,)use a sponge and soapy water, )when using a high pressure washer on persistent marks, do not keepthe lance directed towards thelamps or their edges for too long,so as not to damage their protectivecoating and seals.
)Do not touch the bulb directly withyour fingers, use lint-free cloths. Changing a bulb should only be doneafter the headlamp has been switched off for a few minutes (risk of serious burns).
It is imperative to use only anti-ultraviolet (UV) type bulbs in order notto damage the headlamp. Always replace a failed bulb with a new bulb with the same type andspecification.
Dipped beam headlamps (xenon model)

D1S xenon bulbs must be changedby a CITROËN dealer or a qualifiedworkshop, as there is a risk of electrocution.
It is recommended that the D1S bulbsare changed at the same time when one of them fails.

Practical information
Dipped beam headlamps
(halogen model)





Main beam headlamps (halogen model)
)
Press on the top of the connector thenpivot the assembly downwards. )
Remove the connector with the bulb.)
Remove the bulb and change it.
For reassembly, carry out these operations in
reverse order, but engaging the bottom of thebulb first.

)
Remove the protective plastic cover by
pulling on the tab. )Remove the protective plastic cover bypulling on the tab.)Remove the connector with the bulb by pressing on the lug at the bottom. )Remove the bulb and change it.
For reassembly, carry out these operations in
r
everse order.

Daytime running lamps/sidelamps
For the replacement of this type of LED lamp and lighting guides, contact a CITROËN dealer
or a qualified workshop.

A replacement kit for the LEDs is available fromCITROËN dealers.
Direction indicators
Faster flashing of a direction indicator warning lamp (left or right) indicates a failed bulb on that side.

The direction indicator bulb is located below the front lamp.) Turn the bulb holder a quar ter turn and pull
it out.) Remove the bulb and change it.
For reassembly, carry out these operations in
reverse order.
You can also contact a CITROËN dealer or a
qualified workshop for the replacement of thesebulbs.

Practical information
Fr o nt f oglamps
) Remove the deflector under the body.)
Disconnect the bulb connector.)
Turn the bulb a quarter of a turn, withdraw
and change it.
To r e
fit, carry out these operations in reverseorder.
To replace these bulbs you may also contact a CITROËN dealer or a qualified workshop.
Integrated direction indicator
side repeaters Door mirror spotlamps
You should contact a CITROËN dealer or aqualified workshop for the replacement of thesebulbs.
Y
ou should contact a CITROËN dealer or a qualified workshop for the replacement of the
light emitting diode - LED.

1.Sidelamps(light emitting diodes - LEDs).2.Direction indicators (PY21W amber).3.Reversing lamps (P21W).4. Brake lamps (P21W).5.Foglamps (P21W).
Rear lamps
Direction indicators and brake
lamps (on the wings)
) Open the boot then remove the access cover.)
Disconnect the lamp connector. )
Remove the two lamp fixing nuts.
)Carefully remove the lamp unit from
outside. The retaining clips unclipautomatically. )Turn the bulb holder a quarter of a turn andchange the bulb.
For reassembly, carry out these operations in
reverse order.


Changing the light emittingdiode-LED lamps

For replacement, contact a CITROËN dealer or qualified workshop.