key battery Citroen DS5 HYBRID 2016 1.G Owner's Manual

55
DS5_en_Chap02_ouvertures_ed02-2015
Locking the vehicle
F With the electronic key on your person in
the recognition zone A , press with a finger
or thumb on one of the door handles (at the
markings) to lock the vehicle.
F
Ma

intain pressure with your finger or thumb
until the windows close completely.
Locking is confirmed by fixed
lighting of the direction indicators for
approximately two seconds.
The door mirrors fold at the same time. If one of the doors or the boot is still
open or if the key for Keyless Entry and
Starting system has been left inside
the vehicle or if the ignition is on, the
central locking does not take place.
When the vehicle is locked, if it is
unlocked inadvertently, it will lock itself
again automatically after about thirty
seconds unless a door is opened.
If the alarm was previously activated, it
will not be reactivated automatically.
The folding and unfolding of the door
mirrors by the remote control can be
deactivated by a CITROËN dealer or a
qualified workshop.
As a safety measure (children on
board), never leave the vehicle without
taking the key for the Keyless Entry and
Starting system, even for a short period.
Guard against theft when the key for the
Keyless Entry and Starting system is
in the recognition zone with the vehicle
unlocked.
In order to preserve the charge of the
cell battery in the remote control, the
"hands-free" functions go into extended
stand-by after 21 days of non-use. To
restore these functions, press one of
the remote control buttons or start the
engine with the electronic key in the
reader.
Ensure that nothing and no person
prevents the correct operation of the
windows.
Be particularly aware of children when
operating the windows.
This function allows you to identify
your vehicle from a distance,
particularly in poor light. Your vehicle
must be locked.
Locating your vehicle
F Press the closed padlock on the remote
c
ontrol.
This will switch on the courtesy lamps and
the direction indicators will flash for around
ten
sec

onds.
Access

57
DS5_en_Chap02_ouvertures_ed02-2015
Back-up key
Unlocking / Locking using the integral key with Keyless
Entry and Starting
The integral key is used to lock and unlock the
vehicle when the electronic key cannot operate:
-
ce
ll battery flat, vehicle battery discharged
or disconnected, ...
-
ve

hicle located in an area with strong
electromagnetic signals.
F
Ma

intain a pull on button 1 , to extract the
integral key 2 .
If the alarm is activated, the audible
signal triggered on opening a door
with the key (integral with the remote
control) will stop when the ignition is
switched on.Locking the driver's
door
F Insert the integral key in the door lock, then
t urn it to the rear.
Unlocking the driver's
door
F Insert the integral key in the door lock, then
turn it to the front.
Access

59
DS5_en_Chap02_ouvertures_ed02-2015
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.
changing the cell battery
Battery ref.: CR2032 / 3 volts.
This replacement battery is available from a
CITROËN dealer or a qualified workshop.
A message appears in the instrument panel
screen when replacement of the battery is
needed.
F
Un
clip the cover using a small screwdriver
at the cutout.
F
Li

ft off the cover.
F
Re

move the flat battery from its location.
F
Fi

t the new battery into its location
observing the original direction of fitment.
F
Cl

ip the cover onto the casing.
Remote control problem -
reinitialisation
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F
Pl

ace the mechanical key (integral with the
remote control) in the lock to unlock your
vehicle.
F
Pl

ace the electronic key in the reader.
F
Sw

itch on the ignition by pressing
START/STOP.
The electronic key is fully operational again.
If the problem persists, contact a CITROËN
dealer or a qualified workshop as soon as
possible.
Access

63
DS5_en_Chap02_ouvertures_ed02-2015
System which protects and provides a deterrent
against theft and break-in. It provides the
following types of monitoring:
Alarm
- Exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot or the bonnet...
- Interior volumetric
The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compartment or
moves inside the vehicle.
- Tilt
The system checks for any change in the
attitude of the vehicle.
The alarm is triggered if the vehicle is lifted,
moved or knocked.
Self-protection function
The system checks for the putting out of
service of its components.
The alarm is triggered if the battery, the
button or the wires of the siren are put
out of service or damaged.For all work on the alarm system,
contact a CITROËN dealer or
a
q

ualified workshop.
Locking the vehicle with full
alarm system
Activation
F Switch off the ignition and get out of the vehicle.
F Press the locking button on the
r emote control or lock the vehicle
using the Keyless Entry and
Starting system.
Following an instruction to lock the
vehicle from the remote control or using
the Keyless Entry and Starting system,
the exterior perimeter monitoring is
activated after a delay of 5 seconds,
the interior volumetric monitoring
after 45 seconds and the anti-tilt after
90
s

econds.
If an opening (door, boot...) is not closed
fully, the vehicle is not locked but the
exterior perimeter monitoring will be
activated after a delay of 45 seconds.
The monitoring system is active: the indicator
lamp in the button flashes once per second.
Access

67
DS5_en_Chap02_ouvertures_ed02-2015
Safety anti-pinch
When the window rises and meets an obstacle,
it stops and immediately partially lowers again.
In the event of unwanted opening of the
window on closing, press the switch until the
window opens completely, then pull the switch
immediately until the window closes. Continue
to hold the switch for approximately one second
after the window has closed.
The safety anti-pinch function is not active
during this operation.
deactivating the rear
w indow controls Reinitialisation of the
electric windows
In the event of contact during operation of the windows, you must reverse the movement of
the window. To do this, press the switch concerned.
When operating the passenger electric window switches, the driver must ensure that no one
is preventing correct closing of the windows.
The driver must ensure that the passengers use the electric windows correctly.
Be particularly aware of children when operating the windows.
Be aware of passengers and other persons present close to the vehicle when closing the
windows remotely using the the electronic key or the Keyless Entry and Starting system. Following reconnection of the battery, the
safety anti-pinch function must be reinitialised.
The safety anti-pinch function is not active
during these operations.
For each window:
-
lo

wer the window completely, then raise
it. It will rise in steps of a few centimetres
each time the switch is pressed. Repeat
the operation until the window closes
completely,
-
co
ntinue to press the switch for at least
one
s
econd after reaching this position,
window closed.
For the safety of your children, press
switch 5 to prevent operation of the
rear windows irrespective of their
position.
The warning lamp in the button comes on,
accompanied by a message confirming
activation. It remains on, as long as the child
lock is activated.
The interior controls for the rear doors are also
deactivated.
Opening the doors from the outside and
operation of the rear windows from the driver's
controls remain possible.
Access

101
DS5_en_Chap04_conduite_ed02-2015
Switching off using the
electronic key
F Immobilise the vehicle.
Electronic key left in the
reader
If the electronic key is left in the reader,
on opening the driver's door a message
appears to warn you.
Switching off with Keyless
Entry and Starting
F Immobilise the vehicle.I f the vehicle is not immobilised, the
engine will not stop.
Never leave your vehicle with the
electronic key still inside.
Switching the ignition on
(without starting)
F With the electronic key inside
t he vehicle, press the " S TA R T/
STOP " button.
The engine stops and the steering
column locks. F
Pr
ess the "
START/STOP "
button.
The engine stops and the steering
column locks.
Anti-theft protection
Electronic engine immobiliser
The keys contain an electronic chip which has
a secret code. When the ignition is switched
on, this code must be recognised in order for
starting to be possible.
This electronic engine immobiliser locks the
engine management system a few minutes
after the ignition is switched off and prevents
starting of the engine by anyone who does not
have the key.
In the event of a malfunction, you are informed
by a message in the instrument panel screen.
In this case, your vehicle does not start; contact
a CITROËN dealer as soon as possible.
With the electronic key in the reader or the
Keyless Entry and Starting key inside the
vehicle, pressing the "START/STOP" button,
with no action on the pedals
, allows the
ignition to be switched on.
F
Re

move the electronic key from the reader. F
Pr

ess the "START/STOP" button,
the instrument panel comes on
but the engine does not start.
F
Pr

ess the button again to switch
off the ignition and so allow the
vehicle to be locked.
With the ignition on, the system goes
into energy economy mode when
necessary to maintain the state of
charge of the battery.
Switching off the engine leads to a loss
of braking assistance.
driving

DS5_en_Chap08_info-pratiques_ed02-2015
disconnecting the battery
In order to maintain an adequate state
of charge for starting the engine, it is
recommended that the battery be disconnected
if the vehicle is taken out of service for a long
period.
Wait 2 minutes after switching off the ignition
before disconnecting the battery.
F
cl
ose the windows and the doors before
disconnecting the battery,
F
sw

itch off all electrical consumers (audio
system, wipers, lighting, ...),
F
sw

itch off the ignition and wait for
four
mi

nutes.
Having exposed the battery, it is only
necessary to disconnect the (+) terminal.
Quick release terminal
dis

connecting the (+) terminal
F Raise the lever A fully to release the
c lamp B.
Following reconnection of the battery
Reconnecting the (+) terminal
F Position the open clamp B of the cable on
t
he positive post (+) of the battery.
F
Pr

ess down on the clamp to position it
correctly on the battery post.
F
Lo

ck the clamp by lowering the lever A .
Do not force the lever as locking will
not be possible if the clamp is not
positioned correctly; start the procedure
again. The Stop & Start system may not be
operational during the trip following the
first engine start.
In this case, the system will only be
available again after a continuous
period of immobilisation of the vehicle,
a period which depends on the ambient
temperature and the state of charge of
the battery (up to about 8 hours).
After reconnecting the battery, switch on the
ignition and wait 1 minute before starting to
allow initialisation of the electronic systems.
However, if minor problems persist following
this operation, contact a CITROËN dealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise or reset certain
systems, such as:
-
th

e remote control or electronic key
(depending on version),
-
th
e electric blind(s),
-
th
e electric windows
-
th
e date and time,
-
th
e radio preset stations.

15Hybrid4 system

Starting the Hybrid4 system


Activation of the Hybrid4 system

On activation of the Hybrid4 system, the
instrument panel lights up, the power indicator
needle is placed at position " 0
". The steering
column automatically unlocks (perceptible
noise and movement of the steering column).
Depending on certain parameters, such as the
state of charge of the high voltage battery or
the ambient temperature, the Hybrid4 system
itself determines whether it is necessary to
start the HDi Diesel engine.
The mode selector is at the AUTO
position.

In wintry conditions with the
engine cold, the Diesel pre-
heating warning lamp can stay
on for a few seconds; wait until
it goes off before releasing the
brake pedal.






























Starting - switching off the Hybrid4 system


Never leave children alone inside the
vehicle when the Hybrid4 system is
active.



)
Place the gear selector at position N
.

)
Insert the electronic key in the reader.
or


)
With Keyless Entry and Starting, simply
having the electronic key inside the vehicle
is sufficient.
)
Press the brake pedal firmly.


)
Make a single short press (about one
second) on the " START/STOP
" button.

)
Maintain pressure on the brake pedal until
the READY
lamp comes on, signalling
activation of the Hybrid4 system, confirmed
by an audible signal.

If the Hybrid4 system does not activate:


)
If N
is flashing in the instrument
panel, move the gear selector to
position A
then to position N
.

)
If the " Foot on the brake
" is
displayed, press the brake pedal
firmly.


The READY
lamp may come on after
a few seconds if there is a demand
for activation of the Hybrid4 system
after energy economy mode has been
entered.

17Hybrid4 system

Switching off the Hybrid4 system




)
Immobilise the vehicle.

)
Place the gear selector in position N
.

)
Make a short press (about one second) on
the " START/STOP
" button.
The Hybrid4 stops:


- the READY
lamp goes off,

- the steering column locks,

- the electric parking brake is applied
automatically, unless its automatic mode is
deactivated.


)
Check that the parking brake warning
lamps are on.

)
Remove the electronic key from the reader.

Before doing anything under the
bonnet, the Hybrid4 must be switched
off ( READY
lamp off) and the electric
parking brake must be applied.

Check that the READY
lamp is off
before leaving the vehicle.
Never leave the electronic key in the
vehicle in your absence.





For reasons of safety and theft protection,
do not leave your electronic key in the
vehicle, even when you are close to it.
It is recommended that you keep it on
your person.
















Switching the ignition on


With the electronic key in the reader or the
Keyless Entry and Starting key inside the
vehicle, pressing the " START/STOP
" button,
with no action on the brake pedal
, allows the
ignition to be switched on.



)
Press the " START/STOP
"
button, the instrument panel
comes on but the Hybrid4 system
does not start up.

With the ignition on, the system goes
into energy economy mode when
necessary to maintain the state of
charge of the battery.

)
Press this button again to switch off the
ignition and so allow the vehicle to be
locked.

45Alphabetical index
Advice on driving ............................................ 23
Air conditioning ......................................... 22, 25
Bag hook ......................................................... 31
Back up starting .............................................. 18
Battery, 12 V ...................................................... 5
Battery, high voltage ........................ 5, 27-29, 39
Boot floor, removable ...................................... 31
Cable, high voltage ......................................... 28
Car wash ......................................................... 36
Cooling, high voltage battery .......................... 29
Defrosting ........................................................ 25
Demisting ........................................................ 25
Display screen, instrument panel ......... 8, 10, 13
Driving economically....................................... 24
Eco-driving ..................................................... 24
ECO OFF (switch) ........................................... 22
Electric running (ZEV) ............ 11, 20, 22, 24, 25
Electronic key .......................................15, 17, 18
Emergency switching off ................................. 18
Energy flows ............................................. 10, 11
Energy recovery .................................... 9, 11, 24Keyless Entry and Starting ..................15, 17, 18
Key not recognised ......................................... 18
Kit, temporary puncture repair ........................ 37
Filter, particle ........................................ 5, 26, 42
Fittings, boot ................................................... 31
Flat bed (recovery) .......................................... 38
Four-wheel drive (4WD) ................ 19, 21, 23, 38
Fuel consumption .................................. 9, 12, 24
Gearbox, electronic ...................5, 15, 23 -25, 32
Gear selector, electronic gearbox .................. 32 Engine compartment ...................................... 30
Engine, Diesel .....................5, 19, 22, 25, 36, 40
Environment .................................................... 24
Opening the bonnet ........................................ 30
Ignition on........................................................ 17
Indicator, power................................................. 9
Instrument panel ............................................... 8 Head-up display .............................................. 16
Heating ...................................................... 22, 25
High voltage .............................................. 27, 28
Histogram, fuel consumption .......................... 12Mode selector ......................................... 2, 7, 19
Motor, electric ....................................... 5, 19, 39
Parcel shelf, rear ............................................. 31
Parking brake, electric ........................ 15, 23, 36
Power indicator ............................................. 8, 9
Puncture .......................................................... 37A
B
C
D
EH
IK
F
GM
O
P