turn signal Citroen DS5 HYBRID4 2013 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2013, Model line: DS5 HYBRID4, Model: Citroen DS5 HYBRID4 2013 1.GPages: 364, PDF Size: 10.21 MB
Page 69 of 364
67
Monitoring
Low fuel level
fixed with the two last
bars flashing.When it first comes on there remainsapproximately 6 litres offfuel
in the
tank. Yo u m u s t r e
fuel as soon as possible to avoid running out of fuel.This warning lamp will come on every time the ignition
is switched on, until a sufficient addition of fuel is made.
Fuel tank capacity: approximately 60 litres.
Never continue to drive until you run out of fuel as
this could damage the emission control and injection systems.
Warning / indicator lampStateCauseAction / Observations
Airbags
on temporarily. This lamp comes on for a fewseconds when you turn on the
ignition, then goes off. This lamp should
go off when the engine is started.
If it does not go off, contact a CITROËN dealer or a qualified workshop.
fixed. One of the airbag or seat belt pretensioner systems has a fault. Have it checked by a CITROËN dealer or a qualified
workshop.
Directionalheadlamps
flashing. The directional headlamps system has a fault. Have it checked by a CITROËN dealer or a qualified
workshop.
Seat belt(s) not fastened / unfastened
fixed
or flashingaccompanied by an
audible signal.
A seat belt has not been fastened or has been unfastened. Pull the strap then inser t the tongue in the buckle.
Page 70 of 364
Coolant temperature
gauge
With the hybrid system active:
- in zone A
, the temperature is correct,
- in zone B, the temperature is too high; the central STOP
warning lamp comes on,
accompanied by an audible signal and amessage in the instrument panel screen.You must stop as soon as it is safe to do so.Wait a few minutes before switching off the engine.
Contact a CITROËN dealer or a qualified
workshop.
A
fter driving for a few minutes, the temperature
and pressure in the cooling system increase.
To top up the level:
)
wait for the engine to cool, )
unscrew the cap by two turns to allow the
pressure to drop,
) when the pressure has dropped, remove
the cap, ) top up the level to the "MAX" mark.
Be aware of the risk of burns whentopping up the cooling system. Do not fill above the maximum level (indicated on the reservoir).
Page 86 of 364
Back-up control
Unlocking/locking using the integral key
The integral key is used to lock and unlock the
vehicle when the electronic key cannot operate:
- cell battery flat, vehicle battery discharged
or disconnected, ...
- vehicle located in an area with stron
gelectromagnetic signals. )Maintain a pull on button 1
, to extract the integral key 2.
Complete unlocking
)
Tu r n t h e k ey towards the front of the vehicle
to unlock the vehicle.
Normal locking
)Turn the key towards the rear of the vehicle
to lock the vehicle completely.
Deadlocking
)Turn the key towards the rear in the driver's door lock to lock the vehicle completely. )Turn the key towards the rear again withinfive seconds to deadlock the vehicle.
Page 129 of 364
127Driving
With the ignition on or the hybrid system active,
to release the parking brake, press the brakepedal, pullthen release control lever A.The full release of the parking brake isconfirmed by:
Manual release
- the braking warning lamp and
the Pwarning lamp in the control lever A
going off,
- the display of a message.
I
f you pull the control lever A
without pressing
the brake pedal, the parking brake will not
be released and a message appears in the
instrument panel.
If necessar
y, you can make a maximum application
of the parking brake. It is obtained
by means of a long pull on control lever A ,
until you see a message and an audible signalis heard.
Maximum application is essential:
- in the case of a vehicle towing a trailer,
if the automatic functions are activated
but you are applying the parking brakemanually,
- when the slope you are parked on mayvary (e.g. on a ferry, on a lorry, duringtowing).
Maximum application
In the case of towing, a loaded vehicle or parking on a gradient, make amaximum application of the parkingbrake then turn the front wheels towardsthe pavement and engage a gear whenyou park.
After a maximum application, the release time will be longer.
Before leaving the vehicle, check that parking brake warning lamps in the instrument panel and the control lever Aare on fixed, not flashing. With the vehicle stationar
y, to apply the parkingbrake whether the hybrid system is active or not, pull
control lever A .
Manual application
The application of the parking brake is confirmed by:
- illumination of the brakin
g warning
lamp and of the P warning lamp in
the control lever A ,
- the display of a message.
When the driver
’s door is opened with the hybrid system active, there is an audible signal
and a message is displayed if the parking brakehas not been applied.
Page 151 of 364
149Driving
Reversing camera
A reversing camera is activated automatically
when reverse gear is engaged.
The colour image is provided in the navigationscreen. The
green lines represent the general direction of the vehicle.
The red lines represent around 30 cm beyond
the limit of your vehicle's rear bumper. The
audible signal becomes continuous from thislimit.
The blue lines represent the maximum turningcircle.
Clean the reversing camera regularly using a sponge and a soft cloth.
Page 158 of 364
switched on automatically, without any action on
the par t of the driver, when a low level of external
li
ght is detected or in certain cases of activation of
the windscreen wipers.
As soon as the brightness returns to a sufficient
level or after the windscreen wipers are switched
off, the lamps are switched off automaticall
y.
Automatic illumination of headlamps
Activation
)Turn the ring to the "AU TO "position,automatic illumination of headlamps is activated and a message is displayed in the screen.
Deactivation
)Turn the ring to another position. Deactivation is accompanied by a message in the screen.
Association with the automatic "Guide-me-home" lighting
Association with the automatic lighting provides
the "guide-me-home" lighting with the following
additional options after the ignition is switchedoff:
- selection of the lighting duration of 15, 30or 60 seconds in the vehicle parameters in
the vehicle configuration menu,
- automatic activation of "guide-me-home"lighting when automatic illumination of
headlamps is in operation.
Operating fault
In the event of a malfunctionof the sunshine sensor,
the lighting comes on, this
warning lamp is displayed in the instrumentpanel and/or a message appears in the screen,
accompanied by an audible signal.
Contact a CITROËN dealer or a qualified
wor
kshop.
In fog or snow, the sunshine sensor may detect sufficient light. In this case, thelighting will not come on automatically. Do not cover the sunshine sensor,coupled with the rain sensor andlocated in the centre of the windscreen behind the rear view mirror; theassociated functions would no longer be controlled.