stop start Citroen DS5 RHD 2014 1.G Owner's Guide

97Comfort

4. Automatic visibility
programme

For maximum cooling or heating of the
passenger compartment, it is possible
to exceed the minimum value 14 or the
maximum value 28.



Turn control 2
or 3
to the left
until "LO"
is displayed or to the
right until "HI"
is displayed.
See "Front demisting - defrosting".



2-3. Driver's-passenger's side
settings
The driver and front passenger can
each adjust the temperature to their
requirements.



Turn control 2
or 3
to the left or to the right
respectively to decrease or increase this
value.
A setting around the value 21 provides
optimum comfort. However, depending on your
requirements, a setting between 18 and 24 is
normal.
You are advised to avoid a left / right setting
difference of more than 3.


Manual operation

If you wish, you can make a different choice
from that offered by the system by changing a
setting. The "AUTO "
indicator lamps go off; the
other functions, except the air conditioning, will
still be controlled automatically.



Pressing the "AUTO "
button returns the
system to completely automatic operation.






With Stop & Start, when demisting has
been activated, the STOP mode is not
available. The value indicated on the display corresponds
to a level of comfort and not to a temperature in
degrees Celsius or Fahrenheit.


Switch off the demisting/defrosting
of the rear screen and door mirrors
as soon as appropriate, as lower
current consumption results in
reduced fuel consumption.


Front Demist -
Defrost







Rear screen and door mirrors demist -
defrost



It is possible to stop the
demisting/defrosting operation
before it is switched off
automatically by pressing the
button again. The indicator
lamp associated with the
button goes off.













Automatic visibility programme

Switching on







With Stop & Start, when demisting has
been activated, the STOP mode is not
available.


Switching off

The demisting/defrosting switches off automatically
to prevent an excessive consumption of current.



Select this programme
to demist or defrost the
windscreen and side windows
as quickly as possible.
The system automatically manages the air
conditioning, air flow and air intake, and
provides optimum distribution towards the
windscreen and side windows.




To stop the programme, press either
the "visibility"
button again or "AUTO "
, the
indicator lamp in the button goes off and the
indicator lamp in the "AUTO "
button comes on.

The system starts again with the values in
use before it was overridden by the visibility
programme.



Press this button (located on
the air conditioning system
control panel) to demist /defrost
the rear screen and the door
mirrors. The indicator lamp
associated with the button
comes on.










The rear screen demist - defrost
can only operate when the engine is
running.

Starting-switching off the engine




Insert the electronic key in the reader.


Press the brake pedal for vehicles with
an automatic or electronic gearbox, or
fully declutch for vehicles with a manual
gearbox.

Starting using
the electronic key
Starting with the "Keyless
Entry and Starting" system

If one of the starting conditions is not
met, a reminder message appears in
the instrument panel screen. In some
circumstances, it is necessary to turn
the steering wheel slightly while pressing
the "START/STOP" button to assist
unlocking of the steering; a message
warns you when this is needed.
With a manual gearbox
, put the gear lever in neutral.
With an electronic gearbox
, put the gear lever in N
.
With an automatic gearbox
, put the gear lever in P
or N
.

For Diesel vehicles
, in
temperatures below zero the
engine will not start until the
preheater warning lamp has gone off.
If this warning lamp comes on after
pressing "START/STOP", you should
hold the brake or clutch pedal down
until the warning lamp goes off and
do not press the START/STOP button
again.



With the electronic key inside the vehicle
(it is not necessary to put it in the reader),
press the brake pedal for vehicles with an
automatic or electronic gearbox, or fully
declutch for vehicles with a manual gearbox.

Press the " START/STOP
"
button.
The engine starts (see the
warning below for Diesel
vehicles).


Press the " START/STOP
" button.
The engine starts (see the
warning below for Diesel
vehicles).
The "Keyless Entry and Starting" device
must be in the recognition zone.
For safety reasons, do not leave
this zone with the vehicle running.

105Driving

Switching off using the
electronic key



Immobilise the vehicle.


Electronic key left in the reader

If the electronic key is left in the reader,
on opening the driver's door a message
appears to warn you.



Stopping with the "Keyless
Entry and Starting" system



Immobilise the vehicle.

If the vehicle is not immobilised, the
engine will not stop.
















Ignition on without
starting



With the electronic key inside
the vehicle, press the " START/
STOP
" button.
The engine stops and the
steering column locks.

Press the " START/STOP
"
button.
The engine stops and the
steering column locks.











Anti-theft protection


Electronic engine immobiliser

The keys contain an electronic chip which has
a secret code. When the ignition is switched
on, this code must be recognised in order for
starting to be possible.
This electronic engine immobiliser locks the
engine management system a few minutes
after the ignition is switched off and prevents
starting of the engine by anyone who does not
have the key.
In the event of a malfunction, you are informed
by a message in the instrument panel screen.
In this case, your vehicle does not start; contact
a CITROËN dealer as soon as possible.

With the electronic key in the reader or the
Keyless Entry and Starting key inside the
vehicle, pressing the "START/STOP" button,
with no action on the pedals
, allows the
ignition to be switched on.


Remove the electronic key from the reader.



Press the "START/STOP" button,
the instrument panel comes on
but the engine does not start.


Press the button again to switch
off the ignition and so allow the
vehicle to be locked.


With the ignition on, the system goes
into energy economy mode when
necessary to maintain the state of
charge of the battery.


Switching off the engine leads to a loss
of braking assistance.

Emergency starting with the
Keyless Entry and Starting
system
When the electronic key is in the recognition
zone and your vehicle does not start after
pressing the "START/STOP" button:



Insert the electronic key in the reader.


Press the brake pedal on vehicles with an
automatic or electronic gearbox, or fully
declutch with a manual gearbox.


Press the "START/STOP" button.
The engine starts.
In the event of an emergency only, the engine
can be switched of without conditions. To do
this, press and hold the "START/STOP" button
for about 3 seconds.
In this case the steering column locks as soon
as the vehicle stops.
If the electronic key is no longer in the
recognition zone when driving or when you
(later) request switching off the engine, a
message appears in the instrument panel.

Emergency switch- off
Electronic key not recognised by
the "Keyless Entry and Starting"
system



Press and hold the "START/STOP" button
for about 3 seconds if you want to force
switching off the engine (note that restarting
will not be possible without the key).

123Driving

You must press the brake pedal when
starting the engine.
Whatever the circumstances, you must
manually apply the parking brake when
parking, unless the parking brake is
programmed in automatic mode.

When immobilising the vehicle, with
the engine running, you must place the
gear lever in neutral N
.
Before carrying out any work in the
engine compartment, check that the
gear lever is in neutral N
and that the
parking brake is applied.



Stopping the vehicle

With the ignition on, the
flashing of this warning lamp,
accompanied by an audible
signal and a message
in the instrument panel screen, indicates a
malfunction of the gearbox.
Have it checked by CITROËN or a qualified
workshop. Before switching off the engine, you can
choose to:


- move to position N
to engage neutral,

- leave the gear engaged; in this case, it will
not be possible to move the vehicle.
In both cases, you should apply the parking
brake to immobilise the vehicle.

Operating fault

Sport setting




After selection of manual or
automated mode, press the
S
button to switch on the Sport
setting, which provides a more
dynamic driving style.
S
appears alongside the gear
engaged in the instrument panel
screen.


Press the S
button again to switch it off.
S
then disappears from the instrument
panel screen.
The Sport setting is switched off every time the
ignition is switched off.

127Driving














Stop & Start


Operation


Going into engine STOP mode

The "ECO"
warning lamp comes on
in the instrument panel and the engine
goes into standby automatically:


- with a manual gearbox
, at speeds below
12 mph (20 km/h) or vehicle stationary with
the Blue HDi 120 version, when you place
the gear lever in neutral, and you release
the clutch pedal,

- with an electronic gearbox
, at speeds
below 5 mph (8 km/h), when you press
the brake pedal or put the gear lever in
position N
,

- with an automatic gearbox
, vehicle
stationary, when you press the brake pedal
or put the gear lever in position N
. If your vehicle is fitted with the system, a time
counter calculates the sum of the periods in
STOP mode during a journey. It resets itself to
zero every time the ignition is switched on with
the START/STOP button.

Never refuel with the engine in STOP
mode; you must switch off the ignition
with the START/STOP button.
For your comfort, during parking
maoeuvres, STOP mode is not
available for a few seconds after
coming out of reverse gear.
STOP mode does not affect the
functionality of the vehicle, such as for
example, braking, power steering...


Special cases: STOP mode not
available
STOP mode is not invoked when:


- the vehicle is on a steep slop (rising or
falling),

- the driver's door is open,

- the driver's seat belt is not fastened,

- the vehicle has not exceeded 6 mph
(10 km/h) since the last engine start using
the START/STOP button,

- the electric parking brake is applied or
being applied,

- the engine is needed to maintain a
comfortable temperature in the passenger
compartment,

- demisting is active,

- some special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.
In this case, the "ECO"
warning lamp
flashes for a few seconds then goes
off. The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...).
The engine restarts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Start system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.

This operation is per fectly normal.

Going into engine START mode

The "ECO"
warning lamp goes off
and the engine starts automatically:


- with a manual gearbox
, when you fully

depress the clutch pedal,

- with an electronic gearbox
:


●
gear lever in position A
or M
, when you
release the brake pedal,

●
or gear lever in position N
and brake
pedal released, when you place the gear
lever in position A
or M
,

●
or when you engage reverse.

- with an automatic gearbox
:


●
gear lever in position D
or M
, when you
release the brake pedal,

●
or gear lever in position N
and brake
pedal released, when you place the gear
lever in position D
or M
,

●
or when you engage reverse.

START mode is invoked automatically when:


- the driver's door is open,

- the driver's seat belt is not fastened,

- the speed of the vehicle exceeds 15 mph
(25 km/h) with a manual gearbox (2 mph
(3 km/h) with the Blue HDi 120 version),
7 mph (11 km/h) with an electronic gearbox
and 2 mph (3 km/h) with an automatic
gearbox.

- the electric parking brake is being applied,

- some special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system.


Special cases: START invoked
automatically

If the system has been deactivated
in STOP mode, the engine restarts
immediately.
At any time, press the "ECO OFF"
switch to
deactivate the system.
This is confirmed by the switch warning lamp
coming on accompanied by a message in the
screen.

Deactivation

In this case the "ECO"
warning lamp
flashes for a few seconds, then goes
off.

This operation is per fectly normal.

129Driving

The system is reactivated automatically
at every new start using the START/
STOP button.



Reactivation

Press the "ECO OFF"
switch again.
The system is active again; this is confirmed
by the switch warning lamp going off and a
message in the screen.

Operating fault

In the event of a fault with the system, the
"ECO OFF"
switch warning lamp flashes then
comes on continuously.
Have it checked by a CITROËN dealer or a
qualified workshop.
In the event of a fault in STOP mode, the vehicle
may stall.
All of the instrument panel warning lamps come
on.
Depending on version, an alert message may also
be displayed, asking you to place the gear lever in
position N
and put your foot on the brake pedal.
It is then necessary to switch off the ignition and
start the engine again using the "START/STOP"
button.
Before doing anything under the
bonnet, deactivate the Stop & Start
system to avoid any risk of injury
resulting from automatic operation of
START mode.
This system requires a 12 V battery with a
special specification and technology (reference
numbers available from CITROËN dealers).
Fitting a battery not listed by CITROËN
introduces the risk of malfunction of the
system.
For charging, use a 12 V charger and do not
reverse the polarity.

Maintenance


The Stop & Start system makes use of
advanced technology. For any work on
the system go to a qualified workshop
with the skills and equipment required,
which a CITROËN dealer is able to
provide.


With the engine running, press button 1
.
The activated/deactivated status when the
engine was switched off is retained when
the engine is switched on again.
The strip retracts automatically 3 seconds after
switching off the engine except in STOP mode
of Stop & Start.


Activation / Deactivation




With the engine running, adjust the
brightness of the information using
button 3
:


- towards the rear to increase the
brightness,

- towards the front to decrease the
brightness.





Brightness adjustment


We recommend that adjustments are
only made using these buttons when
the vehicle is stationary.
When stationary or while driving, no
objects should be placed around the
transparent strip (or on its cover) to
avoid blocking the strip output and
preventing its correct operation.

In certain extreme weather conditions
(rain and/or snow, bright sunshine, ...)
the head-up display may not be legible
or may suffer temporary inter ference.
Some sunglasses may hamper reading
of the information.
To clean the transparent strip, use a
clean, soft cloth (such as a spectacles
cloth or microfibre cloth). Do not use
a dry or abrasive cloth or detergent or
solvent products as these could scratch
the strip or damage the anti-reflection
coating.



Height adjustment




With the engine running, adjust the display
to the required height using button 2
:


- towards the rear to move the display up,

- towards the front to move the display
down.