ESP Citroen GRAND C4 PICASSO RHD 2017 2.G Owner's Guide

147
Operating fault
Have it checked by a CITROËN dealer or a
qualified workshop.
In the event of a fault in STOP mode, the vehicle
may stall.
All of the instrument panel warning lamps come on.
Depending on version, an alert message may also
be displayed, asking you to place the gear selector
lever at position N and put your foot on the brake
pedal.
It is then necessary to switch off the ignition and
start the engine again using the "START/STOP"
button.
In the event of a fault with the system,
this indicator lamp flashes for a few
moments then comes on continuously,
accompanied by a message.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system to avoid the risk of injury related
to an automatic change to START
mode.
Driving on flooded roads
Before driving through a flooded road,
it is strongly recommended that you
deactivate the Stop & Start system.
For more information on Driving
advice
, particularly on flooded roads,
refer to the corresponding section. The Stop & Start system requires a
battery of advanced technology and
special characteristics.
All work on this type of battery must
only be done by a CITROËN dealer or a
qualified workshop.
For more information on the 12 V
battery
, refer to the corresponding
section.
4
Driving

148
Memorising speeds
Memorising
This function allows speeds to be saved, which can then be offered to set the two systems: the speed limiter (to limit the speed of the vehicle) or the
cruise control (for a vehicle cruising speed).
You can memorise up to six speed settings for each of the two systems. By default, some speed settings are already memorised.F

S
elect the system for which you want to
memorise new speed settings.
This function is accessible in the Driving
menu
of the touch screen.
F

Sel
ect the " Driving function " tab, then
" Speed settings ".
F

P
ress the button corresponding to the
speed setting you want to modify.
As a safety measure, the driver must
carry out these operations when
stationary.
F

E
nter the new value using the numerical
keypad and confirm.
Driving

151
Memorising the speed setting
This memorisation is in addition to the display
of Speed limit recognition .
The driver can choose to adapt the speed
setting to the speed limit suggested, by
pressing the memorisation button at the speed
limiter controls, with the standard cruise
control, the dynamic cruise control or the
dynamic cruise control with Stop function.
This speed setting then replaces the previous
speed setting for the speed limiter and/or cruise
control. For more information on the Speed
limiter , Cruise control , Dynamic
cruise control or Dynamic cruise
control with Stop function , refer to
the corresponding sections. 1.
S

elect speed limiter/cruise control mode.
2.
M

emorise a speed setting.
Operating limits
The legislation on speed limits is specific to
each country.
The system does not take account of reduced
speed limits in the following cases:
-
p
oor weather (rain, snow),
-
a

tmospheric pollution,
-

t
railer, caravan,
-

d
riving with a space-saver type spare
wheel or snow chains fitted,
-

p
uncture repair using the temporary
repair
k

it,
-
y

oung drivers,
-
...
T

he system may be disrupted or not work at all
in the following situations:
-

p
oor visibility (inadequate street lighting,
falling snow, rain, fog),
-

w
indscreen area ahead of the camera dirty,
misty, frosty, covered with snow, damaged
or masked by a sticker,
-

f
ault with the camera,
-

o
bsolete or incorrect mapping,
-

h
idden road signs (other vehicles,
vegetation, snow),
-

s
peed limit signs that do not conform to the
standard, are damaged or distorted. 3.
S

peed limiter indication.
4.
M

emorise the speed.
5.
C

urrent speed setting.Steering mounted controls
Display in the instrument panel
4
Driving

153
Steering mounted controls
6. Speed limiter on / pause indication.
7. Speed limiter mode selection indication.
8.
S

peed limiter setting.
Speed limiter - "LIMIT"
System which prevents the vehicle from exceeding the speed programmed by the driver.
The speed limiter cannot, in any circumstances,
replace the need to observe speed limits, nor can it
replace the need for vigilance on the part of the driver.
Once the programmed speed limit is reached,
additional pressure on the accelerator pedal
has no effect.
1.
S

elect speed limiter mode.
2.
L

ower programmed speed.
3.
R

aise programmed speed.
4.
S

peed limiter on / pause.
5.
D

isplay the list of memorised speeds or,
A

ccept the speed proposed by the speed
limit recognition.Displays in the instrument panel
S witching on the speed limiter requires
a programmed speed of at least 20 mph
(30
km/h).
The speed limiter is paused by operation of the
control.
The programmed speed can be exceeded
temporarily by pressing the accelerator firmly
beyond the point of resistance.
To return to the programmed speed, simply
release the accelerator pedal until the vehicle
returns to the programmed speed limit.
The programmed speed remains in the
memory when the ignition is switched off. For more information on Memorising speeds ,
refer to the corresponding section.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding section.
4
Driving

154
Switching on / Pause
F Turn thumbwheel 1 to the "LIMIT" position:
the speed limiter mode is selected but is
not switched on (Pause).
F

S
witch the speed limiter back on by
pressing button 4 , if the speed displayed
is suitable (by default, the last speed
programmed).
F

Y
ou can temporarily stop the speed limiter
by pressing button 4 again: the display
confirms that it has been stopped (Pause). You do not have to switch the speed limiter on
in order to set the speed.
Once the function is selected, you can modify
the speed setting by:
-

u
sing buttons 2 and 3, raising or lowering
the speed displayed:
F

b
y successive short presses, to modify
by + or - 1 mph (km/h),
F

b
y a maintained press, to modify in steps
of + or - 5 mph (km/h).
Adjusting the speed limiter
setting
- pressing button 5 :
F t he six speeds memorised are displayed
in the touch screen,
F

p
ress the button corresponding to the
limit speed chosen.
The value is displayed in the instrument panel.
The selection screen closes after a few
moments.
-

b
y pressing button 5 , if your vehicle has
speed limit recognition:
F

t
he speed to memorise is displayed in
the instrument panel,
F
press button 5 again to save the speed.
The value is then displayed in the instrument
panel.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding section.
Driving

156
Steering mounted controls
6. Cruise control pause / resume indication.
7. Cruise control mode selection indication.
8.
Spe

ed setting.
Cruise control - "CRUISE"
System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.
The cruise control system cannot, in any circumstances, replace the need to observe speed limits, nor can it replace the need for vigilance on the part of the driver.
You are advised to keep your feet near the pedals at all times.
S
witching on the cruise control requires a
minimum vehicle speed of 25 mph (40 km/h).
As well as engagement of:
-

f

ourth gear or higher on a manual gearbox,
-

s

econd gear or higher in manual mode on
an automatic gearbox,
-

position
D on an automatic gearbox.
The system remains active after changing gear
on vehicles with a manual gearbox and Stop &
Start.
The cruise control is paused by pressing
button 4 or the brake pedal or on triggering of
the ESC system for safety reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal until the
programmed cruise speed is reached again. 1.
S
elect cruise control mode.
2.
S
et the current speed of the vehicle
as the programmed speed / Lower the
programmed speed.
3.
S
et the current speed of the vehicle
as the programmed speed / Raise the
programmed speed.
4.
P
ause / resume cruise control.
5.
D
isplay the list of memorised speeds or,
A

ccept the speed suggested by the speed
limit recognition system.
Displays in the instrument panel
Switching off the ignition cancels any
programmed speed value. For more information on Memorising speeds
,
refer to the corresponding section.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding section.
Driving

157
Exceeding the programmed
speed
If the cruise speed setting is exceeded, the
displayed speed flashes.
The display becomes steady again once the
vehicle returns to the cruise speed setting.
Switching off
F Turn thumbwheel 1 to the "0" position. T
he display of information related to the
cruise control disappears.
Switching on
Once the cruise control is switched on, you
can modify the cruising speed in one of the
following ways:
-

u
sing buttons 2 or 3 :
F

b
y successive short presses, to modify
the speed by + or - 1 mph (km/h),
F

b
y a long press, to modify the speed in
steps of + or - 5 mph (km/h),
-

b
y pressing button 5 :
F

t
he six memorised speeds are displayed
in the touch screen,
F

c
hoose a value: it is displayed in the
instrument panel.
The selection screen closes after a few
moments.
The modification is then accepted.
F

T

urn thumbwheel 1 to the "CRUISE"

position: the cruise control mode is
selected but is paused.
F
P
ress button 2 or 3 : your vehicle's current
speed becomes the cruise speed.
The cruise control is activated (ON).
Modification of the cruise speed
(speed setting)- by pressing button 5 , if your vehicle has
speed limit recognition:
F

t
he speed to memorise is displayed in
the instrument panel,
F
press button 5 again to save the speed.
The value is then displayed in the instrument
panel.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding section.
Pause
You can pause the cruise control at any time
by pressing button 4 : the screen confirms the
pause.
4
Driving

159
Dynamic cruise control
System that allows, in addition to maintaining your vehicle's speed at a value that you have defined, the inter-vehicle time you have selected between
your vehicle and the one in front to be maintained.
Principles of operation
Using a radar with a range of about 100 metres,
located at the front of the vehicle, this system
detects a vehicle running in front of your
vehicle.
It automatically adapts the speed of the vehicle
to that of the vehicle in front.
If the vehicle in front is running more slowly,
the system progressively reduces the speed of
your vehicle using just engine braking (as if the
driver had pressed the "-" button).
If your vehicle is too close to or approaching
the vehicle in front too quickly, the dynamic
cruise control is automatically deactivated.
The driver is then alerted by an audible signal,
accompanied by a message.
Choice of the type of cruise control
The choice between the "dynamic" and
"standard" cruise control is done in the Driving
menu.
F

I
n the Driving menu, select the " Driving
function " tab, then " Cruise control
active " to activate or deactivate the
dynamic cruise control.
For more information on the Cruise
control , refer to the corresponding
section. F

P
lace the cruise control
thumbwheel at "CRUISE". If the vehicle in front accelerates or changes
lane, the dynamic cruise control progressively
accelerates your vehicle to return to the
programmed speed.
If the driver operates a direction indicator to
the left (left-hand drive) or the right (right-
hand drive), to overtake a slower vehicle, the
dynamic cruise control allows your vehicle to
temporarily approach the vehicle in front to
assist the overtaking manoeuvre, though never
exceeding the programmed speed.
4
Driving

161
1. Select cruise control mode.
2. Use the current speed of the vehicle as
the cruise speed setting / Lower the speed
setting.
3.
U

se the current speed of the vehicle as
the cruise speed setting / Raise the speed
setting.
4.
P

ause / Resume the cruise control.
5.
D

isplay the list of memorised speeds, or
A

ccept the speed suggested by the speed
limit recognition system.
6.
S

elect the inter-vehicle distance (" Close",
" Normal ", "Distant ")
For more information on Memorising speeds ,
refer to the corresponding section.
For more information on Speed limit
recognition and its memorisation, refer to the
corresponding section.
Steering mounted controls
Switching on
The dynamic cruise control must be selected
in the Driving menu.
F

T
urn the thumbwheel 1 to the " CRUISE"
position: cruise control mode is selected,
but is paused.
F

P
ress one of the buttons 2 or 3 : the current
speed of your vehicle becomes the cruise
speed setting.
The cruise control is activated (ON).
By default, the inter-vehicle time is set at
2
seconds.
Other wise, the last speed value set will be used
for operation of the system.
Modification of the cruise control
speed
- using buttons 2 or 3: F b y successive short presses, to modify
by steps of + or - 1 mph (km/h),
F

b
y a maintained press, to modify by
steps of + or - 5 mph (km/h).
-

b
y pressing button 5 :
F

t
he six memorised speed settings are
displayed in the touch screen,
F

c
hoose a speed setting: it is displayed in
the instrument panel.
The selection screen closes after a few
moments. The modification is then taken into
account.
-

b
y pressing button 5 , if your vehicle has
speed limit recognition:
F

t
he speed to memorise is displayed in
the instrument panel,
F
press button 5 again to save the speed.
The speed setting is then displayed in the
instrument panel.
As a precaution, it is recommended that
you select a speed setting close to the
current speed of your vehicle.
Operation
For more information on Speed limit
recognition and its memorisation, refer to the
corresponding section.
4
Driving

167
Steering mounted controls
1. Select cruise control mode.
2. Use the current speed as the speed
setting
/ Lower the speed setting.
3.
U

se the current speed as the speed
setting
/ Raise the speed setting.
4.
P

ause / Resume cruise control.
5.
U

se the speed suggested by the speed
limit recognition system.
6.
D

isplay and adjust the inter-vehicle
distance setting.
For more information on Speed limit
recognition , refer to the corresponding
section.
Displays in the instrument panel
7. Indication of the presence / absence of a target vehicle.
8.
I

ndication of cruise control activation /
deactivation.
9.
Spe

ed setting.
10.
I

ndication that vehicle is held stationary.
11.
S

peed suggested by the speed limit
recognition system.
If a vehicle is detected, the symbol 7
is filled
with the colour associated with the cruise
control mode. By default, the symbol 7 is
e m pt y.
In cruise control activated mode, the symbol
8
appears in green. By default, the symbol 8
appears in grey. 12 . I
nter-vehicle distance setting.
13. P osition of the vehicle detected by the radar.
This information is visible in the instrument
panel in "DRIVING" display mode.
4
Driving