headlamp Citroen JUMPER 2016 2.G Owner's Guide

150
jumper_en_Chap08_Aide-rapide_ed01-2015
1 - Main beam headlamps
type
d , H7 - 55 W
-
r emove the cover by pulling on the
rubber tongue.
-

Disconnect the electrical connector
.
-
r elease the retaining spring by pressing
on the central clip.
-

Change the bulb taking care to align the

metal part with the groove on the lamp. 2 -
d ipped beam headlamps
type

d , H7 - 55 W
- r emove the cover by pulling on the
rubber tongue.
- Disconnect the electrical connector .
- r elease the retaining spring by pressing
on the central clip.
-

Change the bulb taking care to align the

metal part with the grooves on the lamp.
Front lamps
3 - direction indicators
type A

, WY 21 W - 21 W
-
r emove the cover by pulling on the
rubber tongue.
-

T
urn the bulb holder a quarter turn
anticlockwise.
-

Change the bulb.
o

pen and secure the bonnet with the stay.
To access the bulbs, reach behind the
headlamp unit.
If necessary you can remove the headlamp:
-

Depending on the country of sale,


remove the very low temperature
protection padding by sliding it towards
the outside of the vehicle.
-
Disconnect the electrical connector by

removing its locking ring.
-
r
emove the two headlamp fixing
screws.
-

Move the headlamp towards the centre


of the vehicle to extract it from its
sliders.
o

n the left hand side, take care not to
dislodge the bonnet stay.
Failed bulb or lamp

151
jumper_en_Chap08_Aide-rapide_ed01-2015
Halogen bulbs must be changed after
the headlamp has been off for several
minutes (risk of serious burns). Do not touch
the bulb directly with your fingers, use a
lint-free cloth.
When each operation has been completed,
check the operation of the lamps.
5 - Front foglamps
type E

, H11 - 55 W
-

Turn the steering so that the wheel on the
side in question is turned fully inwards.
- remove the screw located in the wheel
arch.
-
r emove the protective cover.
LE
d
daytime running lamps
These light-emitting diode (LED) lamps
serve as both daytime running lamps and
sidelamps.
i

f your vehicle is fitted with LED daytime
running lamps, contact a C
i
T
roën
dealer.
4 - Sidelamps / daytime running lamps
type A

, W21/5W - 21W and 5W
-
r
emove the cover by pulling on the
rubber tongue.
-

T

urn the bulb holder a quarter of a turn
anti-clockwise.
-

Change the bulb.
-
r emove the fixing clip and disconnect
the electrical connector.
-
T
urn and disengage the bulb holder
-
Change the bulb taking care to align the

metal part with the grooves on the lamp.
Failed bulb or lamp
QUiCK HELP
8

155
jumper_en_Chap08_Aide-rapide_ed01-2015
cHAnGInG A WIPE r BLA d E
The steps, located in the front bumper,
enable you to reach the blades and the
screenwash jets.changing a front wiper blade
raise the wiper arm.
Unclip the blade by pressing the button and
remove it by pulling it outwards.
Fit the new blade and ensure that it is
secured correctly.
r

eturn the wiper arm to the normal position.
Check that the screenwash or
headlamp wash jets are not blocked.
Worn wiper blade
QUiCK HELP
8

217
jumper_en_Chap10a_Autoradio-Fiat-tactile-1_ed01-2015
Level 1Level 2 Level 3co mment
Settings
Safety /Help
re

versing camera
o
nDisplay the reversing camera in reverse.
of

f
ca

mera delay
o
nMaintain the display in the screen of the image
from the reversing camera for a maximum of
10
seconds or up to 8 mph (18 km/h).
of

f
Settings Lamps
da

ytime lighting
o
nActivate or deactivate the automatic illumination
of headlamps when starting.
of

f
Settings
d

oors and
locking Autoclose
o

nActivate or deactivate the automatic locking of
doors when the vehicle is moving.
of

f
Touch Screen Audio - Telematic System
AUDio and TELEMATiCS
10