Citroen JUMPY MULTISPACE 2010 2.G Repair Manual

56
Ventilation
REAR VENTILATION
If your vehicle is fitted with an additional air
conditioning unit, located in the rear of the
vehicle. The distribution rail located in the
roof and the 6 individualised diffusion vents
provide a perfect diffusion of the ambient air
selected.
The warm air diffused at the floor, from the
front air conditioning unit, is distributed at
the feet of the rear passengers of the
2nd row.
A warm air diffusion vent, located on the
specific unit, completes the assembly for the
feet of the rear passengers of the 3rd row.
Temperature adjustment
Control positioned:
- on the blue, triggers cool air,
- on the red, triggers heating of the ambient air.
Activation/Deactivation
Air flow
The force of the blown air, via the
vents, varies from 1 to the strongest 4.
To obtain a comfortable level of
ambient air, remember to adjust this
control.
To deactivate the blower, place the control in
position 0. This button, located on the
overhead storage unit, enables
you to activate/deactivate the
operation of the rear controls
from the driver's seat or the front passenger
seat.
The first press activates (green diode lit).
A second press deactivates (diode off).

57
Ventilation
EASE OF USE and COMFORT
3
ADDITIONAL HEATING
Vehicles fitted with an HDi engine may be
fitted with a heater. When the engine is at
idle or the vehicle is stationary, it is normal
to notice a high-pitched whistling noise and
a slight emission of smoke and odour.
Rear ventilation
Coolant circuit heater
This is an additional and autonomous
system which heats the diesel engine hot
coolant loop to make starting easier.
It improves the de-icing and demisting
performance.

58
Ventilation
Have the heater checked at least
once a year at the beginning of winter.
Maintenance and repairs should only be
carried out by a CITROËN dealer. Use
recommended replacement parts only. Good practice
To avoid any risk of poisoning or
asphyxiation, the heater must not be used,
even for short periods, in an enclosed space
such as a garage or workshop which is not
fitted with an exhaust gas extraction system.
Do not park the vehicle on an inflammable
surface (dry grass, dead leaves, paper…),
there is a risk of fire.
The temperature near the heater must not
exceed 120 °C. A temperature higher than
this (for example in the case of painting in
an oven) could damage the components of
the electronic circuits.
The heater is supplied by the vehicle's fuel
tank. Ensure that the fuel gauge indicator
light is not at reserve.

60
Seats
FRONT SEATS
Depending on the version and configuration
of your vehicle, different front seats are
fitted, either:
- a driver's seat and a passenger seat,
- an individual driver's seat and a two-seat passenger bench. 3 - Driver's seat height adjustment
Depending on the version and configuration
of your vehicle, you have either:
- a passive adjustment: pull the handle
upwards then take your weight off the
seat to raise, or push on the seat to
lower,
2 - Seat back angle adjustment
Pull the lever upwards and set the required
angle.
1 - Forwards/backwards adjustment
Lift the bar and slide the seat forwards or
backwards.
Depending on the models, the following
adjustments are available:

61
Seats
EASE OF USE and COMFORT
3
- an active adjustment: manoeuvre the handle upwards or downwards until the
desired position is reached.
Head restraint height adjustment
To raise or lower the restraint, pull it
forwards, then slide it. The adjustment is correct when the upper
edge of the head restraint is level with the
top of the head.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
Front heated seat controls
Adjustable armrest
To place the armrest in its rest position:
- raise it until it is in the centreline of the
seat back.
4 - Driver's seat lumbar adjustment
Move the lever up or down to obtain the
required position. To remove it, set it in the high position, press
the tabs and pull upwards and forwards at
the same time.
To re-install, engage the head restraint rods
in the holes, making sure they are aligned
with the seat back.
To place the armrest in a position for use:
- fold it down fully,
- raise it slowly to the required position,
- if you pass the required position, raise it fully then repeat the operations above.
Press the corresponding control,
located on the overhead storage
unit.
The temperature is controlled
automatically.
Pressing a second time stops operation.

2-SEAT FRONT BENCH
If your vehicle is fitted with this bench seat,
it is fixed and has a 3rd seat belt.
Head restraint
Press the tab to adjust the height of the
head restraint.
To remove the head restraint, press the tabs
and raise the head restraint.
The adjustment is correct when the upper
edge of the head restraint is level with the
top of the head.
Never drive with the head restraints
removed; they must be in place and
adjusted correctly.
Seat back pockets
If your vehicle is fitted with these, they are
located on the backs of the front seats.
62
Seats

63
EASE OF USE and COMFORT
3

64
Seats
REAR SEATS
Depending on the version and configuration
of your vehicle, you have different types of
rear seat.
The individual seat is always located on the
right-hand side and the bench on the left-
hand side (in the direction of travel).

Seats
EASE OF USE and COMFORT
3

Type 2: an individual seat the back of which
can be folded to the table position then
raised, facilitating access to the rear space. Individual passenger seat
This seat and the 2-seat bench are
interdependent. Any handling operation must
begin with the individual seat.
Two models are offered:
Two-seat bench
Three models are offered:

Type 1: an individual seat which can be
raised permitting access to the rear space.
Type 1: a two-seat cushion with fixed seat
back.

66
Seats

Type 2: two seats with folding seat backs
and seat cushion which can be raised.

Type 3: a two-seat cushion with individual
tilting seat backs which can be folded to the
table position and cushion which can be
raised. Characteristics dependingon the type of seat
Seat fitted with this control: the seat back
can be tilted.
Seat fitted with this control: the seat back
can be tilted and raised. Seat fitted with this control: the seat back
can be folded and coupled with the raising
control.
"Comma" type head restraint.