remove Citroen XSARA 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 435
BRAKES
B3FP16ED
HANDBRAKE (Adjustment)
Adjustment (continued).
(10)
Nut for adjusting cable tensions
Remove:
The rear wheels.
The drums
(according to version).
Release the handbrake.Use a gauge set to measure at
«a»the travel of the lever
from its stop.
Adjust the nut
(10)to obtain a travel of less than or equal
to 1 mmat «a».
Refit the brake drums without tightening them (accor
ding to version).
Action the handbrake lever 8 times with an effort of
40 m.daN.
With the handbrake released, check the travel of the
lever at
«a», using a gauge set.NOTE:The travel should be less than 1 mm and more
than 0,05 mm.
Refit: The brake drums.
The wheels.
The central console.Check the operation of the handbrake.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 436
BRAKES
B3FP15XC
BLEEDING AND FILLING THE BRAKING SYSTEM
Tools.
[1]
Generic bleeding apparatus: «LURO» or similar.
Bleeding,refilling.
Draining.
Drain the brake fluid reservoir (1)to the maximum (if necessary, use a clean syringe).
Disconnect the connector (4).
Uncouple the pipe (2).
Unscrew the shaft (3).
Remove the reservoir (1).
Empty the brake fluid reservoir (1).
Clean the brake fluid reservoir (1).
Refit:
The brake fluid reservoir
(1).
The shaft (3).
Couple the pipe (2).
Reconnect the connector (4).
Filling the braking system.WARNING:Use only those hydraulic fluids that are approved and recommended.
Fill the brake fluid reservoir (1).
Bleeding the braking system.WARNING:During the bleeding operation, take care to maintain the level of brake fluid in the reser
voir and to top it up, using only brake fluid that is clean and clear.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 438
BRAKES
B3FP160C
BLEEDING AND FILLING THE BRAKING SYSTEM (Continued)
With the bleeding apparatus.
Connect the bleeding apparatus [1]on the brake fluid reservoir (1).
Adjust the apparatus pressure to
2 Bars.
For each circuit:
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw.
Remove the bleeding apparatus
[1].
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
Without the bleeding apparatus.
NOTE:Two operators are necessary.
For each circuit:
Apply the brake pedal to place the circuit under pressure.
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container. Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw.
Remove the tool
[1].
NOTE:Recommence the process a second time if that is necessary.
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 450
BRAKES
HANDBRAKE
XSARA
Checking and adjusting the handbrake.
Remove the handbrake console.
Jack up and chock the vehicle with the rear wheels hanging free. Check the correct routing of the brake cables under the vehicle.
Apply and release the handbrake ten times. Set the handbrake to the
3rd notch.
Tighten the nut (1)until the rear brakes are applied.
Pull the handbrake lever vigorously 4 to 5 times.
Set the handbrake to the 3rd notch.
Check that the rear brakes are applied.
Check that the wheels can be turned freely by hand with the
handbrake released.
Lower the vehicle. Refit the handbrake console.
B3FP095D

Downloaded from www.Manualslib.com manuals search engine 457
BRAKES
B3FP11XD
HANDBRAKE (Adjustment)
XSARA PICASSO
Adjustment.
Remove the handbrake trim (1).
Unclip the sounddeadening (2).
Raise and support the vehicle with the rear wheels
hanging free.
Check the correct routing of the brake cables under the
vehicle.
Apply and release the handbrake
4 times.
Set the handbrake to the 5th notch.
Tighten the nut
(3)until the rear brakes are applied.
Pull the handbrake lever vigorously 4 to 5 times.
Set the handbrake to the 5th notch.
Check that the rear brakes are applied.
With the handbrake released, check that the wheelscan be turned freely by hand.
Lower the vehicle.Refit the sounddeadening
(2)and the handbrake trim (1).

Downloaded from www.Manualslib.com manuals search engine 488
ELECTRICAL
SYSTEM
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Pollen filter
Note:
The pollen filter is located in the engine compartment on the RH side.
Removing.
To remove:
Pull on the tab of the plastic cover (1), at «a».
Tilt the flap
(2).
Remove the pollen filter
(3).
Refitting.
Proceed in reverse order.
C4AP1BRCC4AP1BSCC4AP1BTC
C2

Downloaded from www.Manualslib.com manuals search engine 489
ELECTRICAL
SYSTEM
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Pollen filter
Note:
The pollen filter is located in the engine compartment on the RH side.
Removing.
Remove:
The three screws (1).
The plastic cover (2).
Tilt the flap
(3).
Remove the pollen filter
(4).
Refitting.
Proceed in reverse order.
C4AP169CC4AP16ACC4AP16BC
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 490
AIRCONAIRCON
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Changing the filtering/drying cartridge
Tools.
[1]
Charge station :(according to workshop equipment)[2]TORX adaptor: TORX 70 FACOM
[3]Inertia extractor:1671T Tool kit 4114T
[4]Endpiece Ø 20 : 1671T.D20
[5]Set of plugs: ().0188.T
[6]Circlip pliers: FACOM
Removing.
Depressurise the aircon circuit, using tool [1].
Remove the grille.At
«a», remove the pin and the plastic cover.
Unclip the condenser at «b»and «c», using a screwdriver.
Tilt the condenser towards the front.
Lift and release the condenser.Clean the area around the cap
(3).
Remove the plastic cap (3), using tool [2].
Remove the safety circlip (4), using tool [6].
Position the tool [3]and[4]in the aperture of the cartridge (5).
Extract the cartridge from the reservoir (6), using tool [3]and [4].
Block the reservoir (6), using tool [5].
C4AP163CC4AP164CC4AP166CC4AP165C
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 491
AIRCON
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Changing the filtering/drying cartridge
Refitting.
Remove the new cartridge from its packaging.
Do not expose the cartridge, the filter and seals to pollutants.
Lightly oil the seals
(compressor oil).
Remove tool [5] from the reservoir (6).
Insert the new cartridge (5)into the reservoir (6).
Refit the safety circlip (4), using tool [6].
Make sure that the circlip (4)is correctly positioned in its location.
WARNING: Not more than 5 minutes should elapse between the removal of
the cartridge (6) from its packaging and its being fitted.
Refit:
The plastic cap (3), using tool [5] Tighten to 1,2 ±0,1 m.daN.
The condenser (reclip, pushing at «b»and «c»).
The plastic cover and the pins at «a».
The grille (2).
The screws (1).
Proceed to:
Recharge the circuit
(see corresponding operation).
Check the operation of the air conditioning (see corresponding operation).
C4AP167CC4AP165CC4AP164CC4AP163C
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 492
AIRCONAIRCON
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Pollen filter
XSARA
Removingrefitting.
Remove:
The interior trim (1).
The cover (4).
The pollen filter(3).
Concerns vehicles equipped with aircon without temperature regulation.
Fitting of a new pollen filter necessitates the following operations:
Engage the pollen filter upwards (following arrow «c»).
Slide the pollen filter towards the rear (following arrow «d»).
Position the index (4)on the cover forward of the pollen filter((4)Index on the cover).
C5HP07JC
C5FP075D