Oil drain Citroen XSARA 2004 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 333
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOX
Engines: KFV NFU RFN RHZ
Precautions to be taken.
Repairs on mechanical components.
Never place the gearbox on the ground without protection.
In order to avoid breaking the input shaft ring, it is
imperativethat
the converter retaining bracket should be in place when handlingthe gearbox.
It is
imperativeto use the centring peg and the converter retaining
bracket to couple the gearbox on the engine.
After coupling the gearbox on the engine, remove the centring peg.
Modification of the oil usage counter value.
Exchanging the gearbox ECU:
Note down the gearbox counter value.
Transfer the value read into the the new gearbox ECU.
Exchanging the gearbox :
Initialise the oil usage counter to 0.
Draining the gearbox:
Initialise the oil usage counter(follow the diagnostic tool procedure).
C3 XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 337
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Tightening torques (m.daN).
(1)
Oil flow modulation electrovalve fixing: 1 ± 0,2
(2)
Heat exchanger fixing:5 ±1
(3)
Output speed sensor fixing:1 ±0,2
(4)
Output speed sensor fixing: 1 ± 0,2
(5)
Oil overflow and drain fixing: 4 ± 0,2
(6)
Oil level plug:2,4 ±0,4
(7)
Oil pressure sensor fixing: 0,8 ± 0,1
Engines: KFV NFU RFN RHZ
C3 XSARA XSARA PICASSO
B2CP3EDDB2CP311D

Downloaded from www.Manualslib.com manuals search engine 351
CLUTCH
GEARBOX
TRANSMISSION
DRAINING / FILLING / TOPUP: AL4 GEARBOX
Tools.
[1]
Filling cylinder: ().0341
Draining.
IMPERATIVE:
The gearbox should be drained when the oil is warm (at least 60°C), to
eliminate the impurities in suspension in the oil.
NOTE:Draining is partial, the converter cannot be completely emptied.
Remove the drain plug
(1).
NOTE:Approx. 3 litres of oil should flow out.
Filling.
Refit the drain plug (1)(equipped with a new seal), tighten to2,4 ±0,2 m.daN.
Remove the oil filler cap (2).
Use tool [1].
Oil capacity for dry gearbox:

EW engine:5,85 litres.
DWengine:5,40 litres.
Oil remaining after draining:
3 litres(approx.).Quantity of oil to be put in :3 litres(approx.).Refit the oil filler cap (2)(equipped with a new seal), tighten to 2,4± 0,2 m.daN.
Initialise the oil wear counter (follow the diagnostic tool procedure).
Engines: KFV NFU RFN RHZ
C3 XSARA XSARA PICASSO
B2CP3AYD
B2CP31GC

Downloaded from www.Manualslib.com manuals search engine 352
CLUTCH
GEARBOX
TRANSMISSION
DRAINING / FILLING / TOPUP: AL4 GEARBOX
Checking the oil level.
Prior conditions:
Vehicle in horizontal position.
Check gearbox is not in backup mode.
Remove the oil filler cap
(2).
Add 0.5 litres extra oilinto the gearbox.
Foot on the brake, change through all the gears.
Selection lever in position
"P".
Engine running, at idle.
Oil temperature:
60°C (+8°C; 2°C).
Remove the oil level plug (3).
C3 TU3enginesDimension «X» = 81 mm
XSARA TU5
and EW10 enginesDimension «X» = 81 mm
XSARADW10
enginesDimension «X» = 77 mm
XSARA PICASSO EW10
enginesDimension «X» = 81 mm
Engines: KFV NFU RFN RHZ
C3 XSARA XSARA PICASSO
B2CP3AZD

Downloaded from www.Manualslib.com manuals search engine 353
CLUTCH
GEARBOX
TRANSMISSION
DRAINING / FILLING / TOPUP: AL4 GEARBOX
Thread of oil then "dripdrip".
Refit the plug (3), Tighten to 2,4± 0,2 m.daN.
"Dripdrip" or nothing.
Refit the oil level plug (3).
Stop the engine.Add
0.5 litresextra oil into the gearbox.
Repeat the oil level procedure.
NOTE:The level is correct at the moment the thread of oil becomes “dripdrip”.
Refit the oil level plug
(3)(equipped with a new seal), tighten to2,4±0,2 m.daN.
Checking the oil level (continued).
Refit the oil filler plug (3) (equipped with a new seal), tighten to 2,4± 0,2 m.daN.
An excessive level of oil can lead to the following consequences:
Oil heating up abnormally,
Oil leaks.
A level that is too low will result in the destruction of the gearbox.
Engines: KFV NFU RFN RHZ
C3 XSARA XSARA PICASSO
B2CP3AZD

Downloaded from www.Manualslib.com manuals search engine 496
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Compressor lubricant
ESSENTIAL: The compressor lubricant is extremely hygroscopic; always use FRESH oil.
Checking the compressor oil level
There are three specific cases:
1/
Repairs to a system without leaks.2/Slow leak.3/Fast leak.
1/ Repairing a system without leaks.
a)Using draining/recovery equipment not fitted with an oil decanter.
Drain the system as slowly as possible via the LOW PRESSUREvalve, so as not to lose any oil.
No more oil should be added when filling the system with
R 134.a fluid.
b) Using draining/filling equipment fitted with an oil decanter. Drain the R 134.afluid from the system in accordance with the instructions in the equipment handbook.
Measure the amount of oil recovered.
Add the same amount of
NEWoil when filling the system with R 134.afluid.
c) Replacing a compressor. Remove the old compressor, drain it and measure the oil quantity.
Drain the new compressor (supplied full), so that the same amount of NEWoil is left in the compressor as was in the old compressor.
No more oil should be added when filling the system with R 134.afluid.
AIRCONAIRCON

Downloaded from www.Manualslib.com manuals search engine 497
AIRCON
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Checking the compressor oil level (Continued)
2/ Slow leak.
Slow leaks do not lead to oil loss, therefore the same procedure should be followed as if there was no leak at all.
3/ Fast leak.
This type of leak causes both oil loss as well as allowing air to enter the system.
It is therefore necessary to:
Replace the dehydrator.
Drain as much oil as possible
(when replacing the faulty component).
Either before or during filling of the system with
R 134.afluid, introduce 80 ccof NEWoil into the system.