ESP Citroen XSARA 2005 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 304
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Tool.
[1]Manual vacuum pump: FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness requirements.
EGR valve.
Connect the tool [1]to the capsule union (1).
Apply, several times in succession, a vacuum of approx. 0.6 barto activate the rod "a".
In abrupt reaction to the vacuum, the valve should close on its seating with a clicking noise.
Exhaust gas reycling (EGR) electrovalve.
Check, not under load, between the electrovalve (2)and the EGR valve (1).
Connect the tool [1]between the electrovalve (2)and the capsule (1).
Compare readings with the values in the table below.
Engine speed (rpm) Vacuum value
780 0,5 bar
2500 0 bar
B1HP12GD
Engines: RHY - RHZ
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 304

Downloaded from www.Manualslib.com manuals search engine 345
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS/PRECAUTIONS : AL4 AUTOMATIC GEARBOX
Procedure to be followed prior to carrying out repairs on AL4 autoactive gearbox
If a gearbox malfunction occurs, there are two possible configurations
depending on the seriousness of the fault:
- Gearbox in back-up mode with a replacement programme of
(the fault
values are taken in substitution).
- Gearbox in back-up mode with an emergency programme (3rd hydraulic).
WARNING: In the emergency programme, an impact is felt when
changing P/R, N/R and N/D.
Réception client.
Discuss with the customer, to find out all the malfunction symptoms.
Oil quality - Oil level.
Oil quality.
If the gearbox has suffered a serious fault resulting in a malfunction or
the destruction of a clutch, the oil will overheat and become
contaminated with impurities: the oil is said to be «burnt».
This is characterised by a black colour and the presence of an
unpleasant smell.
ESSENTIAL: The gearbox must be replaced.Oil level
(see corresponding operation).
An excessive oil level can result in the following consequences:
- Excessive heating of the oil.
- Oil leaks.
An insufficent level causes the destruction of the gearbox.
Top up the level of oil in the gearbox
(if necessary).
Check using a diagnostic tool.
Read the fault codes
(engine and gearbox).
Absence of fault codes.
Carry out parameter measures, actuator tests and a road test.
Presence of fault codes.
Carry out the necessary repairs.
Delete the fault codes.
Carry out a road test to check the repair and, if need be, modify the
gearbox ECU parameters
(this is essential after an initialisation of the
ECU).
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 345

Downloaded from www.Manualslib.com manuals search engine 348
CLUTCH
GEARBOX
TRANSMISSION
C4 - XSARA - XSARA PICASSOTIGHTENING TORQUES: AL4 AUTOMATIC GEARBOX
Engines: NFU - RFJ
B2CP3EED
B2CP3X8C
Tightening torques (m.daN).
(8) Fixing of converter on diaphragm
Pre-tightening: 1 ± 0,1
Tightening: 3 ± 0,3
(9)Plug fixing: 0,8 ± 0,2
(10)Gearbox fixing on engine: 5,2 ± 1
Hydraulic block fixing.
Centre the hydraulic block, using screws (11) and (12)
Pre-tighten
(no strict order): 0,9
Slacken: All 7 screws
Tighten
(respect the order indicated): 0,75
NOTE: The screw (11)is shouldered.
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 348

Downloaded from www.Manualslib.com manuals search engine 361
AXLES
SUSPENSION
STEERING
AXLE GEOMETRY
Conditions for checking and adjusting
Vehicle heights at reference height
Rear height Front height
L2 L1
Tools : [1] Gauge for measuring the the wheel radius, 4 bolts: 4300-T.
Tyres inflated to correct pressures. Vehicle at reference height.
Steering rack locked at mid point
(see corresponding operation).
H1 = R1 - L1
H1 = Measurement between the measuring zone underneath the front
subframe and the ground.
R1 = Front wheel radius under load.
L1 =Distance between the wheel axis and the measuring zone underneath
the front subframe.H2 = R2 + L2
H2 = Measurement between the measuring zone underneath the rear sill
and the ground.
R2 =Rear wheel radius under load.
L2 =Distance between the wheel axis and the measuring zone underneath
the rear sill.
E1AP0F3D
C4
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 361

Downloaded from www.Manualslib.com manuals search engine 388
AXLES
SUSPENSION
STEERING
H1 = R1 – L1 H1’ = R1 – L1’
H1 = From the front suspension arm linkage bolt axis to the ground.
R1 =Radius of the front wheel when laden.
L1 =From the centre of the wheel to the front suspension arm linkage
bolt axis.
H1' =From the front jacking point to the ground.
L1' =From the front jacking point to the radius of the front wheel when
laden.H2 = R2 - L2
H2 = From the rear axle silentblock face to the ground.
R2 =Radius of the rear wheel when laden.
L2 =From the centre of the wheel to the rear axle silentblock face.
AXLE GEOMETRY
Measurements at reference height
NOTE: To make the setting of reference height easier, it is acceptable to take the measurement from the flange of the jacking point.
WARNING: The values shown should only be used as guides. In case of doubt, check the settings at reference height
Rear heightFront height
B3CP05BCB3CP058DB3DP079C
XSARA PICASSO
Conditions for checking and adjusting: Tyres inflated to correct pressures. Vehicle at reference height. Steering rack locked at mid point(see corresponding operation).
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 388

Downloaded from www.Manualslib.com manuals search engine 399
BRAKES
23,8 (in click) (1)
25,4/ BOSCH/MCT8 (2)
BOSCH/ZOH 54/26TEVES/F
BOSCH/ZOH 54/26TEVES/F
N3 57/26 N3 57/26
283 302 283 302
26/24
GALFER/G4554 JURID 976 GALFER/G4554 JURID 976
BOSCH/TRW C38
249
9/7
GALFER/G4554
BRAKE SPECIFICATIONS
Master cylinder
ØAmplifier
mm
Supplier
FTpistons
Disc Ventilated
Disc thickness
Brake pad grade
ØCylinder or caliper
RR mm Disc Plain
Disc thickness
Brake pad gradeWith ESP
ET3J4 TU5JP4 EW10A/J4 EW10J4S DV6TED4/ATED4DW10
BTED4
Manual/Automatic
(1) AFU system (EBA) =Emergency Brake Assist (incorporated as standard).(2) AFD system =Automatic lighting of hazard warning lamps on emergency braking (incorporated as standard).Brake fluid reservoir.Supplier: BOSCH, brake fluid quality: DOT 4.The brake fluid reservoir is in 2 parts: the principal reservoir (equipped with a level detector)and a
separate reservoir, they are linked by a rislan pipe by means of a clickfit union.
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 399

Downloaded from www.Manualslib.com manuals search engine 401
BRAKES
TIGHTENING TORQUES: BRAKING SYSTEM
Front brakes
1Front brake disc1 ± 0,1
2Yoke on caliper3 ± 0,3
3Unions on brake piping1,5 ± 0,1
4Caliper on pivot10,5 ± 1
5ABS/ESP hydraulic block support on the chassis member0,2 ± 0,1
6Wheel sensor0,8 ± 0,1
B3FP7DVD
B3FP7DWD
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 401

Downloaded from www.Manualslib.com manuals search engine 404
BRAKES
B3FP7E2D
ABS/ESP HYDRAULIC BLOCK
Components Supplier Type Observations
Hydraulic blockBOSCHABS REF 8.0
Installed under the front LH
ESP 8.0chassis member. 4 regulation channels.
The emergency braking control is incorporated in the primary piston at «a».
B3FP7E3C
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 404

Downloaded from www.Manualslib.com manuals search engine 405
BRAKES
PARKING BRAKE ADJUSTMENT
Adjustment.
IMPERATIVE: Respect the safety and cleanliness requirements.
Raise and support the vehicle.
Remove the central console.
WARNING: Check the routing of the brake cables under the vehicle.
Release the handbrake lever.
Press gently on the brake pedal
(then repeat the operation 3 times).
Action the handbrake lever with a force of 40 daN.
Use a feeler gauge at «J»to measure the movement of the lever in relation to its stop.
NOTE:The movement should be less than 1,5 mmand more than 0,05 mm.
(1)Nut for adjusting the tension of the handbrake cables
Move the nut (1)to obtain a movement «J»less than or equal to 1,5 mm.
Action the handbrake lever 8 timeswith a force of 40 daN.
With the handbrake released, check the movement «j»with a feeler gauge.
NOTE:The movement should be less than 1,5 mmand more than 0,05 mm.
Refit the central console
(see corresponding operation).
Check the efficiency of the handbrake.
B3FP7F1C
B3FP7F2D
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 405

Downloaded from www.Manualslib.com manuals search engine 407
BRAKES
B3FP7ESD
BLEEDING AND FILLING THE BRAKING SYSTEM
Disconnect the connector «b».
Uncouple the pipe (5).
Remove the reservoir (6), moving aside the tabs «c»of the pins (7).
Clean the brake fluid reservoir (4) and the brake fluid reservoir (6).
Refit the brake fluid reservoir (6).
Couple the pipe (5).
Reconnect the connector «b».
Couple the clickfit union, at «a».
Refit:
- The brake fluid reservoir (4).
- The screws (1).
- The filter of the brake fluid reservoir.
- The battery tray.
- The screws (3).
- The battery.
Reconnect the battery.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the
battery
(see corresponding operation).
B3FP7ERC
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 407