Head 6fz Citroen XSARA PICASSO 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 90
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
CYLINDER HEAD (mm)
Engine types 6FZ RFN RFS WJY RHY RHZ
Maximum permissible bow 0,05 0,03
Gasket surface regrinding 0,30 0,20 0,40
TIGHTENING TORQUES ( m.daN)
Pretightening (1) Ø 11 : 1 ± 0,1 2 ± 0,1 2,5 ± 0,3
(2) Ø 6 : 1 ± 0,1
Slackening Ø 11 (only)
Tightening Ø 11 to 1 ± 0,1 8,5 ± 0,8 7 ± 0,7
Crankshaft then to 2 ± 0,1
bearing screws Tightening Angular Ø 11 at 70° ± 5° 60° ± 6° 60° ± 6°
Tightening Ø 6 to 1 ± 0,1
Pretightening 1 ± 0,1 4 ± 0,4 2 ± 0,2
ConnectingSlackening 180° (1/2 turn)
rod screws Tightening 2,3 ± 0,2 2,3 ± 0,2 2± 0,2
Angular tightening46°±5°46° ±4,6° 70° ± 7° 70° ± 7°
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine ENGINECYLINDER HEAD
Engine: 6FZ
Identification of cylinder head gasket
B1DP183D
Nominal
dimensionRepair dimension
2 – 4 – 5
4 – 5
R1 R2 R3
1 1,1
0,8 Gasket thickness
(mm)
Supplier MEILLOR Marking zone
"e" Identification zone
"d"
1,3
100
Identification marks
“d”
= Identification zone.
“e”= Marking zone.
NOTE:3 layer metallic gasket
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 101
ENGINE
CYLINDER HEAD
Engine: 6FZ
X =MAX. reusable length NOTE:
Oil the threads and
under the heads of the bolts
(use engine oil or Molykote G
Rapid Plus)
. Pretightening
: 1,5 ± 0,2
Tightening: 5 ± 0,2
Destightening: 360 ° (1 turn)
Tightening: 2 ± 0,2
Angular tightening: 285° ± 5°
B1DP16FC
A = Washer thickness:4 ± 0,2 mm.X= Length under heads of new bolts = 144,5 ±0,5 mm.
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine ENGINE
177
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ RFN 2003 #
Tensioning the timing belt.
Turn the tensioner roller (8)in the direction of the arrow «c», by means of a hexagonal spanner at «d».
Positionner l’index «a»en position «f».
IMPERATVE: The index «a» should go past the slot «g» by an angular value of 10°.
If it does not, replace the tensioner roller or the timing belt and tensioner roller assembly.
Next bring the index «a»to its adjusting position «g», by turning the tensioner roller in the direction of the arrow «e».
WARNING:the index «a»should not pass the slot «g».
Otherwise, repeat the operation to tension the timing belt.
IMPERATIVE: The tensioner roller should not turn during the tightening of its fixing.
If it does, repeat the operation to tension the timing belt.
Tighten the screw (9)of the tensioner roller (8)to 2,1 ± 0,2 m.daN.
IMPERATIVE: The hexagonal tensioner roller drive should be approx. 15° below the level of the cylinder head
gasket «h».
If it is not, replace the tensioner roller or the timing belt and tensioner roller assembly.
B1EP1BEC
B1EP1BFC
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 288
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS
Engines: KFW NFU 6FZ RFN RFS 8HX 9HZ 9HY WJY RHY RHZ
Clutch cable.
Removing.
Uncouple the cable from the lever (1).
Unclip the cable from the gearbox by actioning
the side tabs
(2).
Detach the cable from the bulkhead.
Remove the clip
(3).
Uncouple the cable from the clutch pedal.
B2BP001CB2BP002C
XSARA XSARA PICASSO
B2BP02VC
B2BP02WC
«PUSH» clutch
«PULL» clutch
B2BP03BCB2BP002C

Downloaded from www.Manualslib.com manuals search engine 289
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS
Engines: KFW NFU 6FZ RFN RFS 8HX 9HZ 9HY WJY RHY RHZ
Refitting.
Place the pedal in the high position (contact at “a”).
Attach the cable yoke on the hook of the clutch pedal.
Fit a new clip
(3).
Fit the endpiece (4)to the bulkhead (fit with G6grease).
Clip the endpiece (5)on the gearbox.
Couple the cable to the lever (1).
Depress the clutch cable several times to lodge the cable in place.
Check that the endpiece (4) is correctly lodged on the bulkhead.
Check the operation of the automatic adjusting system.
After fitting the cable, pull the clutch lever in the inverse direction
(direction F), the lever should
move back when pulled by hand.
Press the clutch pedal very lightly and repeat the same operation. The lever should not move
back.
WARNING:If a system blockage is detected when checking, or if the pedal has been removed,
the pedal position must be adjusted. The correct positioning of the pedal is obtained by the
angular displacement of the stop supports
"a"and "b".
B2BP03CD
XSARA XSARA PICASSO
«PUSH» clutch
«PULL» clutch
B2BP03DD

Downloaded from www.Manualslib.com manuals search engine 328
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX CONTROLS
Engines: NFV 6FZ RFN RFS WJY 8HZ 9HZ 9HY RHY RHZ
(1)Gear control lever.
(2) Gear engagement control cable.(*)
(3)
Gear selection control cable.(*)
(4)
Gear selection balljoint Ø 10 mm.
(5) Gear engagement balljoint Ø 10 mm.
(6) Flexible insulating grommet through the bulkhead.
(*)= These two cables cannot be separated.
B2CP3BWD
XSARA XSARA PICASSO