torque Citroen XSARA PICASSO 2005 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 326
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: RFN - RFK - 9HX - 9HY - 9HZ
Tightening torques (m.daN).
(18)Stop guide screw: 1,25 ± 0,2
(19)Speedometer fixing screw: 1,5 ± 0,2
(20) Gearbox support shaft nut : 6,5 ± 0,6
(21)Nuts fixing rubber support: 3 ± 0,2
(22) Gearbox rubber support shaft: 5 ± 0,5
(23)Screw M10fixing the engine/gearbox housing support: 6 ± 0,5
(24) Screws M10fixing the engine/gearbox housing support: 3 ± 0,3
B2CP401C
B2CP400C
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 326

Downloaded from www.Manualslib.com manuals search engine 327
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: 6FZ - RFN - WJY - 8HX - 8HZ - 9HY - 9HZ - RHY - RHZ
T
ightening torques (m.daN).
(23)Clutch bearing guide (3 screws): 1,25 ± 0,2
(24)Clutch housing
(13 screws): 1,3 ± 0,2
(25)Primary shaft nut
(1 screw): 7,25 ± 0,5
(26)Secondary shaft nut
(1 screw): 6,5 ± 0,5
(27)Yoke retaining screw
(2 screws): 1,5 ± 0,2
(28)Differential gearwheel screw
(2 screws): 6,5 ± 0,5
Reverse gear switch (1 screw): 2,5 ± 0,3
(29)Differential housing
(4 screws): 5 ± 0,5
(30)Breather pipe: 1,7 ± 0,2
(31)Rear housing cover screws
(7 screws): 1,25 ± 0,2
(32)Top-up plug
(1 screw): 2,2 ± 0,2
(33) Differential housing screws
(4 screws): 1,25 ± 0,2
(34)Drain plug
(1 screw): 3,5 ± 0,3
B2CP3BRD
XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 327

Downloaded from www.Manualslib.com manuals search engine 328
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: ML6 GEARBOX
Engine: RHR
Tightening torques (m.daN).
(1)Primary shaft screw: 10 ± 1
(2)Bearing guide screw: 2 ± 0,2
(3) Differential gearwheel screw: 7,7 ± 0,3
(4)Secondary shaft screw: 13 ± 1,3
B2CP3ZLD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 328

Downloaded from www.Manualslib.com manuals search engine 329
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: ML6 GEARBOX
Engine: RHR
Tightening torques (m.daN).
(5)Reverse gear switch: 2,5 ± 0,5
(6)Level plug: 3 ± 0,2
(7)Drain plug: 3 ± 0,3
(8)Differential bearing stop plate screw: 3 ± 0,3
(9)Screw fixing gearbox housing / clutch housing: 3 ± 0,3
(10) 6thgear housing fixing screw: 2 ± 0,2
(11)Differential housing fixing
(screws M8): 1,8 ± 0,3
(12)Differential housing fixing
(screws M10): 4 ± 0,8
B2CP3ZMP
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 329

Downloaded from www.Manualslib.com manuals search engine 330
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: ML6 GEARBOX
Engine: RHR
B2CP3ZNC
Tightening torques (m.daN).
(13)Screws/nuts fixing the gearbox support: 4,5 ± 0,4
(14)Screw fixing the rubber bush: 3 ± 0,3
(15) Nut fixing the gearbox casing: 6,5 ± 0,6
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 330

Downloaded from www.Manualslib.com manuals search engine 334
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: MA/5 GEARBOX CONTROLS
Engines: KFW - NFU - 8HX - 8HZ
(1)Gear lever
(2)Gear control bar
(3)Engagement rod
(4)Gear selection rod
(5)Torque reaction rod
(6)Gear engagement ball-joint
(7)Fixed point on gearbox
Adjustment.
The gear control assembly is not adjustable.
The rods do not have threaded ends.
Features.
Grease the gear engagement ball-joint.
WARNING: To secure the ball-joints, set the
gearbox control to neutral. After fitting the gear
control assembly, check that all the gears will
engage without any ”tight spot”.
B2CP27WD
XSARA
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 334

Downloaded from www.Manualslib.com manuals search engine 347
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: AL4 AUTOMATIC GEARBOX
Engines: NFU - RFJ
B2CP3EDD
B2CP3X7D
Tightening torques (m.daN).
(1) Fixing of the electrovalve for modulation of the flow
of oil into the exchanger (EPDE): 1 ± 0,2
(2)Heat exchanger fixing: 5 ± 1
(3) Output speed sensor fixing
(4)Output speed sensor fixing: 1 ± 0,2
(5)Oil overflow and drain fixing(X = 48 mm)
: 0,9 ± 0,2
(6)Oil level plug: 3,3 ± 0,5
(7)Oil pressure sensor fixing: 0,8 ± 0,1
C4 - XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 347

Downloaded from www.Manualslib.com manuals search engine 348
CLUTCH
GEARBOX
TRANSMISSION
C4 - XSARA - XSARA PICASSOTIGHTENING TORQUES: AL4 AUTOMATIC GEARBOX
Engines: NFU - RFJ
B2CP3EED
B2CP3X8C
Tightening torques (m.daN).
(8) Fixing of converter on diaphragm
Pre-tightening: 1 ± 0,1
Tightening: 3 ± 0,3
(9)Plug fixing: 0,8 ± 0,2
(10)Gearbox fixing on engine: 5,2 ± 1
Hydraulic block fixing.
Centre the hydraulic block, using screws (11) and (12)
Pre-tighten
(no strict order): 0,9
Slacken: All 7 screws
Tighten
(respect the order indicated): 0,75
NOTE: The screw (11)is shouldered.
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 348

Downloaded from www.Manualslib.com manuals search engine 349
CLUTCH
GEARBOX
TRANSMISSION
Engines: NFU - RFJ
B2CP3EGC
(13)Fixing of selector lever position switch: 1,5 ± 0,2
(14)Oil filler plug: 2,4 ± 0,4
TIGHTENING TORQUES: AL4 AUTOMATIC GEARBOXC4 - XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 349

Downloaded from www.Manualslib.com manuals search engine 360
CLUTCH
GEARBOX
TRANSMISSION
DRIVESHAFTS - GEARBOX
Tightening torques (m.daN)Gearbox oil seal mandrels
Vehicles GearboxDriveshaft Driveshaft
Engines
bearing nutRH side LH side Toolkit
C4
MA/5ET3J4 TU5JP4
XSARA TU3JP TU5JP4
C4EW10/DV6 7114-T.W 7114-T.X 7116-T
BE4/5All types
XSARA EW7/10J4B DW8
XSARA PICASSO DV6/DW10
C4ML6 DW10BTED4 9017-T.C 5701-T.A 9017-T
TU5JP4 EW10A 2 ± 0,2 32,5 ± 2,6
(-) 0338 J1 (-) 0338 H1
XSARATU5JP EW10J4
+ (-) 0338 J3 (-) 0338 H2
DW10ATED
AL4Seal extractor
RH / LH(-). 0338
XSARA PICASSO EW10J4 (-) 0338 C
(-) 0338 J1 (-) 0338 H1
+ (-) 0338 J3 (-) 0338 H2
Tightening torque (m.daN) for wheel bolts.
C4 = 9 ± 1 XSARA = 8,5 ± 0,8 XSARA PICASSO = 10 ± 1
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 360