temperature Citroen XSARA PICASSO 2005 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 281
ENGINE
CHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
XSARA PICASSO
Engine type NFV 6FZ RFN 9HZ 9HY RHY
Temperature (°C) 90°C 80°C 90°C
Pressure (bars) 3,3 1,5 1,3 2
Rpm 1000
Pressure (bars) 3
Rpm 2000
Pressure (bars) 5
Rpm 3000
Pressure (bars) 4 6,3 3,5 4
Rpm 4000 4000
Tools (Toolkit 4103-T)
2279-T.Bis X X X X X X
4103-T X X X X X X
7001-T X
4202-T X X X
1503-J X X
NOTE: The oil pressure should be checked with the engine hot, after the oil level has been checked.
XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 281

Downloaded from www.Manualslib.com manuals search engine 290
INJECTION
CHECKS: TURBO PRESSURE
Tools.
[1]Pressure gauge for checking boost pressure: 4073-T.A
[2] Sleeve for checking boost pressure: (-).0171.F
Checks.
IMPERATIVE: Respect the following test conditions:
- Engine at operating temperature.
- Vehicle in running order.
- Engine under full load.
Preparation.
Remove the clips (1).
Fit the tool [2]in the place of the duct (2).
Couple the sleeve [2] on the pressure gauge[1]using the tube «a».
Mode of operation.
Position tool [1]in the vehicle.
Start the engine.
Engagefirst gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of 1000 rpm.
Check the pressure: 0,6 ± 0,05bar
(1500 rpm).
Accelerate freely (change from fourth gear to third gear).Check the pressure: 0,9 ± 0,05bar (between 2500and 3500rpm).
Remove tools [1], [2] and «a».
Reposition the tube (2)and tighten the clips(1).
B1BP2NXD
C5FP06RC
Engines: 8HX - 8HZ
XSARA
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 290

Downloaded from www.Manualslib.com manuals search engine INJECTION
291
CHECKS: TURBO PRESSURE
IMPERATIVE: Respect the safety and cleanliness requirements.
Preparation.
IMPERATIVE: Respect the following test conditions:
- Engine at operating temperature.
- Vehicle in running order.
- Engine under full load.
Connect the diagnostic tool to the vehicle's diagnostic socket, carry out parameter measures.
Mode of operation.
Start the engine.
Engage first gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of 1000 rpm.
Check the pressure: 0,6 ± 0,05 bar
(1500 rpm).
Accelerate freely (change from fourth gear to third gear).Check the pressure: 0,9 ± 0,05 bar (between 2500and 3500rpm).
Engines: 9HX - 9HY - 9HZ
C4
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 291

Downloaded from www.Manualslib.com manuals search engine 292
INJECTION
CHECKS: TURBO PRESSURE
IMPERATIVE: Respect the safety and cleanliness requirements.
Preparation.
IMPERATIVE: Respect the following test conditions:
- Engine at operating temperature.
- Vehicle in running order.
- Engine under full load.
Connect the diagnostic tool to the vehicle's diagnostic socket, carry out parameter measures.
Mode of operation.
Start the engine.
Engage first gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of 1000 rpm.
Check the pressure: 0,6 ± 0,05 bar
(1500 rpm).
Accelerate freely (change from fourth gear to third gear).Check the pressure: 0,9 ± 0,05 bar (between 2500and 3500rpm).
Engines: 9HZ - 9HY
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 292

Downloaded from www.Manualslib.com manuals search engine 294
INJECTION
CHECKS: TURBO PRESSURE
Tools.
[1]Pressure gauge for checking boost pressure: 4073-T.A Kit 4073-T
[2]Sleeve for checking boost pressure: 4185-T
Checks.
IMPERATIVE: respect the following checking requirements: Engine at running temperature.
Vehicle running at full load.
Preparation.
Remove the collar (3)and the sleeve.
Insert the tool [2]between the pipe (1)and the duct (2).
Position tool [1]in the vehicle.
Connect the pressure gauge [1]to the tool [2] with its tube «a»long enough for the gauge to be
positioned inside the vehicle.
Procedure.
Start the engine.
Engage first gearand start the engine.
Engage the gears up to third gear.
Decelerate to 2000 rpm.
Gradually accelerate.
Check the pressure: 0.95 ± 0.05 bar.
Remove the tools, refit the collars (3) and the sleeve.
B1BP1ZXD
Engine: RHY
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 294

Downloaded from www.Manualslib.com manuals search engine 295
INJECTION
CHECKS: TURBO PRESSURE
Tools.
[1]Pressure gauge for checking boost pressure: 4073-T.A Kit 4073-T
[2] Sleeve for checking boost pressure: 4185-T
[3]Adaptor sleeve: 4229-T
Checks.
IMPERATIVE: respect the following checking requirements: Engine at running temperature.
Vehicle in running order at full load.
Preparation.
Remove the collar fixing (3).
Insert the tool [2]connected with tool [3], between the pipe (1)and the duct (2).
Position tool [1]in the vehicle.
Connect the sleeve [2]to the tool [1]with its tube «a».
Procedure.
Start the engine.
Engage first gear and start the engine.
Engage the gears up to third gear.
Decelerate to 1000 rpm.
Accelerate hard, and check the pressure: 0.6 ± 0.05 bar
(1500 rpm).
Accelerate freely in kick-down (changing from fourthto third gear).
Check the pressure: 0.95 ± 0.05 bar (between 2500and 3500rpm).
Remove the tools, reposition the pipe (1)and refit the collar (3).
B1HP12JD
Engine: RHZ
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 295

Downloaded from www.Manualslib.com manuals search engine 432
AIR
CONDITIONING
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Pollen filter
XSARA
Removing-refitting.
Remove:
- The interior trim (1).
- The cover (4).
- The pollen filter (3).
Concerns vehicles equipped with aircon without temperature regulation.
Fitting of a new pollen filter necessitates the following operations:
- Engage the pollen filter upwards
(following arrow «c»).- Slide the pollen filter towards the rear (following arrow «d»).- Position the index(4)on the cover forward of the pollen filter ((4)Index on
the cover).
C5HP07JC
C5FP075D
Angl.-t2-page428-456-2005 9/01/06 10:25 Page 432

Downloaded from www.Manualslib.com manuals search engine AIR
CONDITIONING
437
CHECKING THE EFFICIENCY OF THE AIR CONDITIONING SYSTEM
Outillage EXXOTest
Outillage
(flash équipement & matériel).Exxoclim : 2.4.2-1
Mode d’emploi : Voir notice constructeur
Procédure de l’essai.
Contrôle.
Mettre en place l'outillage
(selon notice du constructeur).
Opérations préliminaires.
Fermer tous les aérateurs frontaux.
Démarrer le moteur.
Ouvrir l'aérateur frontal gauche.
Positionner la commande du répartiteur d'air sur«débit frontal».
Activer la commande«recirculation d'air».
Activer la commande"AIR
CONDITIONING ".
Position des commandes de AIR
CONDITIONING :
- Commande de température sur froid maxi.
- Commande de pulseur en position vitesse maximum.
Laisser la AIR
E5AP2N5D
Outillage VALEO
Outillage.
Clim test 2 : 4372-T
E5AP2N4D
Angl.-t2-page428-456-2005 9/01/06 10:25 Page 437

Downloaded from www.Manualslib.com manuals search engine 439
Checking.
Position the toolCLIM TEST II
(according to the manufacturer's instructions).
Preliminary operations.
Close all the front air vents.
Start the engine.
Open the front LH air vent.
Position the air distribution control to«frontal flow».
Activate the«air recirculation» control.
Activate the«air conditioning» control.
Positions of the air conditioning controls:
- Temperature control on maximum cold.
- Blower control in maximum speed position.
Let the air conditioning operate for5 minutes.
CHECKING THE EFFICIENCY OF THE AIR CONDITIONING SYSTEM
E5AP2FAC
Angl.-t2-page428-456-2005 9/01/06 10:25 Page 439

Downloaded from www.Manualslib.com manuals search engine 440
AIR
CONDITIONING
CHECKING THE EFFICIENCY OF THE AIR CONDITIONING SYSTEM
Interpretation of the measurements.
«m»:High pressure.«s»:Over-heating (SC).
«n»:High temperature.«t»:Ambient air temperature.
«p»:Under-cooling (SR).«u»:Blown air temperature.
«q»:Low pressure.«v»: Humidity.
«r»:Low temperature.«w»: Temperature T3.
Under-cooling.
The under-cooling represents the difference between the condensation temperature and the aircon
fluid temperature at the aircon condenser outlet.
The under-cooling gives the quantity of aircon fluid
(in the liquid state)in the air conditioning circuit.
Values for under-cooling (SR).
Values «p» Origins Solutions
SR < 2°CLack of aircon fluid in the aircon condenser
(should be more than 150grammes)
Add some
2°C < SR <4°CLack of aircon fluid in the aircon condenser aircon fluid
(should be around 100to 150grammes)
4°C < SR < 10°C/12°CCorrect quantity
SR > 10°C/12°CRemove some
Excess aircon fluid in the aircon condenser aircon fluid
SR > 15°C
Blown air temperature «u».
The blown air temperature should be between 2°Cand 10°C.
E5AP2FBC
Angl.-t2-page428-456-2005 9/01/06 10:25 Page 440