engine oil Citroen XSARA PICASSO 2005 1.G Repair Manual

Downloaded from www.Manualslib.com manuals search engine 141
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Cylinder block
9 Oil circuit plug 3 ± 0,3
10 Coolant pump screw 1,6 ± 0,3
Crankshaft bearing cap screws (*)
11Pre-tightening2,5 ± 0,2
Angular tightening60°±5°
Con rod cap nuts
Tightening1
12Slackening 180°
Tightening2,3 ± 0,1
Angular tightening45°±5°
Engine: RHR
B1CP0GNPB1CP0DGC
(*) (11) Crankshaft bearing cap screws
C4
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 141

Downloaded from www.Manualslib.com manuals search engine 143
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication
16 Oil pump screw 1,6 ± 0,1
17 Piston skirt spray jet screw 1 ± 0,1
18 Drain plug 3,4 ± 0,4
Oil sump (length 40 mm )
19Pre-tightening1
Tightening1,6 ± 0,3
Oil sump (length 21 mm)
20Pre-tightening1
Tightening1,6 ± 0,3
21 Electric oil gauge 2,7 ± 0,2
Engine: RHR
B1CP0GPP
C4
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 143

Downloaded from www.Manualslib.com manuals search engine 144
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication
22 Oil pressure switch 2 ± 0,2
Oil filter support (*)
23Tightening1 ± 0,1
Tightening2 ± 0,2
24 Oil filter cover 2,5 ± 0,5
Engine: RHR
B1CP0GPPB1FP062C
(*) (23) Sequence of tightening
C4
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 144

Downloaded from www.Manualslib.com manuals search engine 148
ENGINESPECIAL FEATURES - CYLINDER HEAD TIGHTENING
Engines all types
B1DP05BC
Cleaning to be carried out just prior to refitting the cylinder head.
WARNING: Clean the contact faces with the approved CITROËN cleaning product.
Do not use abrasives or cutting tools on the contact faces.
The contact faces must not bear any traces of impact or scratching.
Insert a tap in the threads of the holes in the cylinder block receiving the cylinder head bolts.
Brush the threads of the cylinder head bolts..
Oil the threads and under the heads of the bolts, usingMOLYKOTE G RAPID PLUS.
EnginesTightening Cylinder head bolts
(m.daN)(Max. reusable length in mm)
NFUTightening2 ± 0,2
Angular tightening260° ± 5°122 ± 0,3
Pre-tightening1,5 ± 0,2
KFUTightening2,5 ± 0,2 119
Angular tightening200° ± 5°
6FZ - RFNPre-tightening1,5 ± 0,1
147
Tightening5 ± 0,1
RFJAngular slackening360° ± 2° 127,5 ± 0,5
Tightening2 ± 0,75
RFKAngular tightening285° ± 5° 144,5 ± 0,5
NOTE: Tightening of the cylinder head after a repair is prohibited.
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 148

Downloaded from www.Manualslib.com manuals search engine 149
ENGINE
SPECIAL FEATURES - CYLINDER HEAD TIGHTENING
Engines all types
B1DP05BC
Cleaning to be carried out just prior to refitting the cylinder head.
WARNING: Clean the contact faces with the approved CITROËN cleaning product.
Do not use abrasives or cutting tools on the contact faces.
The contact faces must not bear any traces of impact or scratching.
Insert a tap in the threads of the holes in the cylinder block receiving the cylinder head bolts.
Brush the threads of the cylinder head bolts..
Oil the threads and under the heads of the bolts, using MOLYKOTE G RAPID PLUS.
EnginesTightening Cylinder head bolts
(m.daN)(Max. reusable length in mm)
Pre-tightening2 ± 0,2
WJYTightening6 ± 0,6 125,5
Angular tightening180° ± 5°
Pre-tightening2 ± 0,2
RHY - RHZTightening6 ± 0,6 133,3
Angular tightening220° ± 5°
Pre-tightening2 ± 0,2
Tightening6 ± 0,6
RHRSlackening360° 134,5
Pre-tightening2 ± 0,2
Tightening6 ± 0,6
Angular tightening220° ± 5°
NOTE: Tightening of the cylinder head after a repair is prohibited.
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 149

Downloaded from www.Manualslib.com manuals search engine 150
ENGINESPECIAL FEATURES - CYLINDER HEAD TIGHTENING
Engines all types
B1DP1CLC
Cleaning to be carried out just prior to refitting the cylinder head.
WARNING: Clean the contact faces with the approved CITROËN cleaning product.
Do not use abrasives or cutting tools on the contact faces.
The contact faces must not bear any traces of impact or scratching.
Insert a tap in the threads of the holes in the cylinder block receiving the cylinder head bolts.
Brush the threads of the cylinder head bolts. Oil the threads and under the heads of the bolts, using MOLYKOTE G RAPID PLUS.
EnginesTightening Cylinder head bolts
(m.daN)(Max. reusable length in mm)
Pre-tightening2 ± 0,2
KFW - NFV
Angular tightening240° ± 5°175,5
Pre-tightening2 ± 0,2
8HX - 8HZ
Tightening4 ± 0,4 149
8HY
Angular tightening230° ± 5°
Pre-tightening2 ± 0,2
9HY - 9HZ
Tightening4 ± 0,4 147
9HX
Angular tightening260° ± 5°
NOTE: Tightening of the cylinder head after a repair is prohibited.
B1BP10LC
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 150

Downloaded from www.Manualslib.com manuals search engine 188
ENGINECHECKING THE VALVE TIMING
Engine: KFU
Tools.
[1] Flywheel setting peg: 4507-TA. Toolkit 4507-T
[2] Camshaft setting peg: 4533-TA.C1
[3] Camshaft setting peg: (-).0194.A
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking.
Deconnect the battery.
Remove:
- The engine cover.
- The upper timing cover (1).
- The oil filter (2).
Remove the sparking plugs to facilitate rotation of the engine.
Turn the engine by means of the crankshaft screw.
IMPERATIVE: Never turn the engine backwards.
Suspend the engine.
Remove:
- The screws (3), the upper RH engine support (4)and the screws (5).
B1BP37JC
B1BP37KC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 188

Downloaded from www.Manualslib.com manuals search engine 190
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Tools.
[1]Flywheel setting peg: 4507-T.A
[2]Camshaft setting peg: 4533-T.AC1
[3] Camshaft setting peg: (-).0194.A
[4] Belt retaining pin: 4533-TA.D
IMPERATIVE: Respect the safety and cleanliness requirements.
Setting the timing.
Raise and support the vehicle, wheels hanging.
Disconnect the battery.
Remove the engine cover.
Raise and support the vehicle, wheels hanging.
Remove:
- The accessories drive belt (3)
(see corresponding operation).
- The crankshaft pulley, the engine cover.
- The upper timing cover (1).
- The oil filter (2).
Remove the sparking plugs to facilitate rotation of the engine.
Suspend the engine.
Remove the screws (4), the upper RH engine support (5)and the screws (6).
B1BP37QD
B1BP37RC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 190

Downloaded from www.Manualslib.com manuals search engine 197
ENGINE
CHECKING THE VALVE TIMING
Engine: NFU
Tools.
[1]Flywheel setting peg: 4507-T.A Toolkit 4507-T
[2a]Camshaft setting peg: 4533-TA.C1
[3b]Camshaft setting peg: 4533-TA.C2
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking.
Disconnect the negative terminal of the battery.
Remove:
- The oil filter (1).
- Suspend the engine.
Remove:
- The engine support (2)and the upper timing cover (3).
B1BP2M7C
B1BP381C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 197

Downloaded from www.Manualslib.com manuals search engine 199
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Tools.
[1]Flywheel setting peg: 4507-T.A Toolkit 4507-T
[2a]Camshaft setting peg: 4533-TA.C1
[2b]Camshaft setting peg: 4533-TA.C2
[3]Belt retaining pin: 4533-T.AD
[4]Dynamic tensioner roller pin: 4200-T.H
IMPERATIVE: Respect the safety and cleanliness requirements.
Removing.
Raise and support the vehicle, front wheels hanging
Disconnect the battery.
Remove:
- The auxiliaries drive belt (4)
(see corresponding operation).
- The crankshaft pulley (3).
- The oil filter.
Suspend the engine, using a workshop hoist.
Remove the timing cover, the engine support (1), the intermediate support and the timing cover (2).
B1BP382C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 199