engine Citroen XSARA PICASSO DAG 2005.5 1.G Owner's Manual

2
3
I N B R I E F
I21
63
V E N T I L A T I O N – H E A T I N G
M A N U A L A I R C O N D I T I O N I N G
Air conditioning
The air conditioning only operates when the engine is running.
Press the switch on the dashboard.
Warning lamp on = in operation
Entry of exterior air
Air recirculation
This position prevents the entry of unpleasant odours into the vehicle.
It should be cancelled as soon as possible to renew the air in the passenger compartment as well as to allow demisting.
To enhance the effi ciency and rapidity of the air conditioning in very hot weather, use the air recirculation position.
Move the control 2 fully to the right and pla-ce the air blower control 3 in an intermediate position.
This function should be cancelled when it is no longer needed, to allow renewal of the air in the cabin.
Deicing – demisting of the windscreen and front side windows
- Place the controls for temperature and air flow on maximum,
- close the central air vents,
- operate the air conditioning.
Note : you should not be in Air Recirculation.

I N B R I E F
I27C R U I S E C O N T R O L /« C R U I S E »
Temporary override of the cruise speed
While cruise control is in use, it is still possible to go above the cruise speed simply by pressing the accel erator pedal (for example to overtake another vehicle). The speed displayed on the screen fl ashes.
You have only to release the accelerator pedal to r eturn to your cruise speed.
Adjustment of the memorised speed while cruise cont rol is in operation
You can adjust the cruise speed, displayed in zone B, by pressing :- Button 4 to increase the speed.- Button 2 to decrease the speed.Note: successive presses will modify the speed in
steps of 1 km/h and a continuous press in steps of 5 km/h.
Deactivation of cruise control with memorised speed
- Either press the brake pedal or the clutch pedal.- Or the ESP or ASR systems are active.- Or press on control 3.Note : cruise control is not active if the gear lever is in
Neutral position.
These actions bring up the information « OFF » in zone B of the screen.
These actions do not cancel the cruise speed which remains displayed on the screen.
Reactivation of cruise control
- By recalling the memorised cruise speed :
Following a deactivation, press on control 3.
Your vehicle automatically resumes the memorised cruise speed which is displayed in zone B.
Note: if the memorised cruise speed is a lot higher
than the speed at which the vehicle is currently
moving, the vehicle will accelerate up to the memorised speed.
- By selecting the current speed :
Give a short press on button 2 or 4, once you are travelling at your desired speed.
The information « OFF » then disappears from the screen.
To cancel the function
- By moving the control from position « CRUISE » to position 0.
- By stopping the engine.
The cruise speed chosen previously is no longer memorised.
In the event of a malfunction, a message appears, accompanied by a sound signal.
Contact a CITROËN dealer.
Do not use this function on congested roads or when weather or road conditions are poor.The driver must remain attentive and in complete control of the vehicle.You are recommended to keep your feet within range of the pedals.Cruise control must only be used where road conditions permit driving at a constant speed.

B
1
A
2
3
4
28
I
I N B R I E F
IS P E E D L I M I T E R / « L I M I T »
This driving assistance function allows you to choo se a maximum speed that you wish not to exceed. This has to be a speed greater than 30 km/h (approx. 20 mph).
Control A for the speed limiter is located below the lightin g/signalling Acontrol stalk.
Note: The information relating to the speed limiter is shown in zone B on the screen.
To select the function
Turn control 1 to the position « LIMIT ».
On selection of the function via control 1, the last speed memorised is displayed.
To adjust the maximum speed
Provided the engine is running, you adjust the memo rised speed by pressing :- button 4 to increase the memorised speed,- button 2 to decrease the memorised speed.Note: successive presses will modify the speed in steps of 1 km/h and a continuous press in steps of 5 km/h.
Activation of the maximum speedAs you see the desired maximum speed displayed, pre ss control 3 to activate 3the limitation.
The information « OFF » then disappears from zone B.
The trip mileage recorder is shown.
While the function is active, action on the accelerator pedal will not
permit the programmed speed to be exceeded, unless you press the
pedal hard down to go beyond the tight spot (see «Temporary override of the maximum speed»).
Note : the vehicle speed may vary slightly from that memor ised.

29
I N B R I E F
IS P E E D L I M I T E R / « L I M I T »
To deactivate the maximum speed
Press button 3 at the end of the control 3A.
This action brings up the information « OFF » on the screen. This action does not cancel the memorised speed which remains displayed in zone B.
Temporary override of the maximum speed
It is possible at any time to drive at above the memorised maximum speed by pressing the pedal hard do wn to go beyond the tight spot.
All the time the speed is being exceeded, the displayed speed flashes.
You have only to release the accelerator pedal to r eturn below the limit speed, making the function ac tive again.
Note : if during speed limitation the system is unable to keep to the memorised speed (e.g. on a steep descen t or under heavy acceleration), then the speed fl ashes. Adapt your speed as necessary.
The function will reactivate when your speed is again below the desired limit speed.
To cancel the function
- By moving the control from position « LIMIT » to position 0.
- By stopping the engine. The speed chosen previously is memorised.
In the event of a malfunction, a message appears, accompanied by a sound signal.
Contact a CITROËN dealer.
A fl oor mat not approved by CITROËN may risk sliding forward under the accelerator pedal and preventing you from pressing beyond the tight spot. It will then be impossible to exit the speed limitation, except by actioning the control under the steering wheel.
The driver must remain attentive and keep complete control of the vehicle.

35S T E E R I N G L O C K – I G N I T I O N - S T A R T E R
NEVER REMOVE THE IGNITION KEY UNTIL THE ENGINE HAS COMPLETELY STOPPED.
IT IS IMPERATIVE ALWAYS TO KEEP THE ENGINE RUNNING IN ORDER TO RETAIN THE BRAKING AND STEERING ASSISTANCE (risk of the steering lock engaging and loss of the safety features).
When the vehicle is stopped and the engine switched off, after you remove the ignition key turn the steering wheel slightly so as to engage the steering lock.

63IIIIIIV E N T I L A T I O N - H E A T I N G
M A N U A L A I R C O N D I T I O N I N G
Entry of air
Make sure that the exterior air inlet grille and manifold at the base of the windscreen is clean and free of dead leaves, snow, etc..If you wash the vehicle using a high pressure jet, avoid targeting anywhere near the air inlet.
Air vents
The face-level air vents have controls for adjusting the air ow and grilles for orienting the direction.
Air circulation
Maximum comfort is obtained from having a good distribution of air in both the front and the rear of the passenger compartment. Air outlets on the oor beneath the front seats enhance comfort for rear passengers, so you should make sure that these outlets are not obstructed.
Pollen lter
Your installation has a lter for excluding dust.This lter has to be changed at the prescribed maintenance intervals (see the Maintenance Guide).
Additional heating
Vehicles with HDi engines may be tted with an automatic additional heating system for enhancing your comfort.
It is normal to notice certain emissions of fumes and odours, especially when stationary, with the engine running at idle.
Air conditioning
Whatever the time of year, the air conditioning is useful in removing humidity and misting.
To keep the air conditioning compressor well sealed , it is essential to operate the air conditioning at least once in every month.
To be effective, the air conditioning should only b e operated with the windows closed.
If after a prolonged stop in bright sunshine, the inside temperature has become excessive, open the windows for a few moments to air the cabin, then close the windows again.
The temperature inside the cabin cannot be lower than the ambient temperature if the air conditioning is not operating.
If you are pulling a heavy trailer in very high ambient temperatures, the air conditioning may temporarily be interrupted if the engine cooling requirements demand this.
Water arising from the condensation in the air conditioning system drains out through a hole provided for that purpose; a pool of water may thus be observed underneath the vehicle when stationary.
It is recommended to have the air conditioning system checked on a regular basis (see the Maintenance Guide).
The air conditioning uses power from the engine to operate. There is a resulting slight increase in fu el consumption.

2
3
18
7
65
4
910
64A U T O M A T I C T E M P E R A T U R E
R E G U L A T I O N
1 - Automatic operation
This is the optimal and normal mode
for using the air conditioning system
to ensure a circulation of air suf cient to maintain a good level of comfort.
A press on the control for this, con rmed by
the display of « AUTO », provides automatic
operation at the selected temperature of the
following 5 functions :
- Air ow.
- Cabin temperature.
- Air distribution.
- Air conditioning.
- Air recirculation. Is is advised to keep all the air vents open.Notes :
- When starting the engine from cold, in order to prevent an unwanted rush of cold
air, the blower attains its optimum level only
progressively. - When you are entering the vehicle after a fairly prolon-
ged stop and the temperature inside the cabin is far
colder (or far hotter) than would be comfortable, it is
no use altering the displayed temperature to try to res-
tore the desired comfort level more rapidly. The system
automatically strives to compensate this temperature
discrepancy as rapidly as possible.
2- Adjustment of temperature
To display the desired temperature,
press one of the buttons :
To increase the temperature
To decrease the température
Display of the temperature requested for the cabin
A setting close to 21 will provide a good comfort l evel.
Manual resumption of one or more functions
It is possible to adjust any of the following functions
manually, while retaining all the other functions in
automatic mode. The warning lamp for the «AUTO»
function will then go out.IIIIII

Picasso 2004-1C:\Documentum\Checkout\N68_04_01_T081-ENG.win 23/4/2
004 13:12
IV IVL E V E L S
Radiator - coolant
The coolant must only be checked
or topped up if the power unit is
cold.
Engine hot:
Wait fifteen minutes or until such
time as the temperature is below
100°C, then slowly untighten the
cap to allow the pressure to fall,
taking care to protect yourself with
e.g. a cloth. Topping up the cooling system
The coolant level should be between the
MAXandMIN
marks on the header tank.
Top up the level. If you have to add more than 1 litre, you
should have the cooling system checked by CITROËN.
Make sure that the cap is on correctly.
Note: The necessity to top up frequently would indicate a
malfunction that should be checked at the earliest opportun ity.
Renewal of coolant fluid should be carried out only by a CITRO ËN Dealer.
Quality: See “Maintenance Guide”.
When working under the bonnet, when the engine is hot (even st opped
and the ignition switched off), the cooling fan could operat e at any time.
Note : The cooling fan may operate for some ten minutes after the engine has been
switched off.
96

99C A P A C I T I E S
Capacity (in litres) 1.6i 2.0i HDi HDi HDi 16V 90 92 110Capacity (in litres) 1.6i
- Engine oil
Drain/re ll lter cartridge With change of lter cartridge lter cartridge 3.50 4.25 4.50 3.85 3.85
- Screen wash fl uid 4.00 4.00 4.00 4.00 4.00
3.50
4.00
lter cartridge
IVIV

A
CB
Starting the engine after a battery disconnection and reconnection
- Turn the ignition key.- Wait approx. ten seconds before actioning the starter so as to allow the electronic systems to reinitialise. It may be necessary to re-enter the radio code.
Note : After a battery disconnection or if there is a malfunction, you must rei-nitialise the anti-pinch on the driver’s window and on the sun roof.
Be aware that, during this manoeuvre, the anti-pinch device is not operational.
With removable front LH seat : To access the battery : - slide the seat as far as possible forwards,- remove the plastic protection A, at the rear of the seat.To change the battery :- remove the head restraint,- slide the seat as far as possible forwards,- using the tool located in the rear LH storage compartment, undo the two screws B situated at the rear on the RH slide and the screw C situated at the rear on the LH slide,- then slide the seat as far as possi-ble rearwards,- tilt the seat forwards to access the battery.To reposition the front LH seat :- perform the above actions in re-verse order,- check that the seat is properly se-cured.
Change of battery.
Replace the battery with one of the same type (with venting).
1001 2 V O L T B A T T E R Y IVIV