turn signal Citroen XSARA PICASSO DAG 2005.5 1.G Owner's Manual

3
2
1
0
4
I N B R I E F
I14
Windscreen wiper stalk
3 Fast speed
2 Normal speed
1 Intermittent or automatic wipe
0 Stop
4 Single wipe – Press the stalk downwards
Vehicle not tted with a rain sensor.Position 1: The timing of the in-termittent wipe adjusts automati-cally to the speed of the vehicle.Note: In position 2 or 3: when stationary, the windscreen wiper speed automatically reduces.
For safety, the wiper sys-
tem is deactivated when
the ignition is switched off.
Vehicle tted with a rain sen-sor.Position 1: Intermittent wipe in-tervals adjust automatically ac-cording to rain intensity.Note: In position 2 or 3: when sta tionary, the windscreen wiper speed automatically reduces.
For safety, the wiper system is deactivated when the ignition is switched off.
When switching the ignition on, to reactivate the function:- return to the Stop position,- change to the desired posi-tion.
The activation of the function is signalled by one wipe.
WARNING:
Do not cover the rain sensor,
which is situated at bottom cen-
tre of the windscreen and visible
from the driving position.
Advice
Washing the vehicle: switch off the ignition.
A sound alert (beep) accom-panied by a message when you activate the automatic wipe mode, indicates that this system is malfunctioning.
Advice
The windscreen wipers can be stopped in maintenance position (forrepairs).
For this, switch off ignition, push the wash/wipe control stalk downwards.
To return to the stop position, simply move the stalk again.
14V I S I B I L I T Y

B
A
2
3
4
26
I
I N B R I E F
IC R U I S E C O N T R O L /«C R U I S E»
This driving assistance function allows you to drive at the speed of your
choIce without the need to action the accelerator.
It is available at speeds above 40 km/h (25 mph), in the higher gears
only.
Control A for cruise control is located below the lighting/signalling control
stalk.
Note: Information relating to the cruise control is displ ayed in zone B
on the display.
To select the function
Turn control 1 to the « CRUISE » position.
To select a cruise speed
On selection of the function via control 1, no cruise
speed has yet been memorised.
Accelerate to the desired speed, then give a short press on button 2 or
button 4.
The cruise speed is then memorised. It is displayed
in zone B on the screen.
The trip mileage recorder then displays.
You can then release the accelerator pedal. The veh icle will
automatically keep to that chosen speed
Note : The vehicle speed may vary slightly from that memor ised.
Cruise control should only be used when the traffi c conditions permit driving at a constant speed.

I N B R I E F
I27C R U I S E C O N T R O L /« C R U I S E »
Temporary override of the cruise speed
While cruise control is in use, it is still possible to go above the cruise speed simply by pressing the accel erator pedal (for example to overtake another vehicle). The speed displayed on the screen fl ashes.
You have only to release the accelerator pedal to r eturn to your cruise speed.
Adjustment of the memorised speed while cruise cont rol is in operation
You can adjust the cruise speed, displayed in zone B, by pressing :- Button 4 to increase the speed.- Button 2 to decrease the speed.Note: successive presses will modify the speed in
steps of 1 km/h and a continuous press in steps of 5 km/h.
Deactivation of cruise control with memorised speed
- Either press the brake pedal or the clutch pedal.- Or the ESP or ASR systems are active.- Or press on control 3.Note : cruise control is not active if the gear lever is in
Neutral position.
These actions bring up the information « OFF » in zone B of the screen.
These actions do not cancel the cruise speed which remains displayed on the screen.
Reactivation of cruise control
- By recalling the memorised cruise speed :
Following a deactivation, press on control 3.
Your vehicle automatically resumes the memorised cruise speed which is displayed in zone B.
Note: if the memorised cruise speed is a lot higher
than the speed at which the vehicle is currently
moving, the vehicle will accelerate up to the memorised speed.
- By selecting the current speed :
Give a short press on button 2 or 4, once you are travelling at your desired speed.
The information « OFF » then disappears from the screen.
To cancel the function
- By moving the control from position « CRUISE » to position 0.
- By stopping the engine.
The cruise speed chosen previously is no longer memorised.
In the event of a malfunction, a message appears, accompanied by a sound signal.
Contact a CITROËN dealer.
Do not use this function on congested roads or when weather or road conditions are poor.The driver must remain attentive and in complete control of the vehicle.You are recommended to keep your feet within range of the pedals.Cruise control must only be used where road conditions permit driving at a constant speed.

B
1
A
2
3
4
28
I
I N B R I E F
IS P E E D L I M I T E R / « L I M I T »
This driving assistance function allows you to choo se a maximum speed that you wish not to exceed. This has to be a speed greater than 30 km/h (approx. 20 mph).
Control A for the speed limiter is located below the lightin g/signalling Acontrol stalk.
Note: The information relating to the speed limiter is shown in zone B on the screen.
To select the function
Turn control 1 to the position « LIMIT ».
On selection of the function via control 1, the last speed memorised is displayed.
To adjust the maximum speed
Provided the engine is running, you adjust the memo rised speed by pressing :- button 4 to increase the memorised speed,- button 2 to decrease the memorised speed.Note: successive presses will modify the speed in steps of 1 km/h and a continuous press in steps of 5 km/h.
Activation of the maximum speedAs you see the desired maximum speed displayed, pre ss control 3 to activate 3the limitation.
The information « OFF » then disappears from zone B.
The trip mileage recorder is shown.
While the function is active, action on the accelerator pedal will not
permit the programmed speed to be exceeded, unless you press the
pedal hard down to go beyond the tight spot (see «Temporary override of the maximum speed»).
Note : the vehicle speed may vary slightly from that memor ised.

29
I N B R I E F
IS P E E D L I M I T E R / « L I M I T »
To deactivate the maximum speed
Press button 3 at the end of the control 3A.
This action brings up the information « OFF » on the screen. This action does not cancel the memorised speed which remains displayed in zone B.
Temporary override of the maximum speed
It is possible at any time to drive at above the memorised maximum speed by pressing the pedal hard do wn to go beyond the tight spot.
All the time the speed is being exceeded, the displayed speed flashes.
You have only to release the accelerator pedal to r eturn below the limit speed, making the function ac tive again.
Note : if during speed limitation the system is unable to keep to the memorised speed (e.g. on a steep descen t or under heavy acceleration), then the speed fl ashes. Adapt your speed as necessary.
The function will reactivate when your speed is again below the desired limit speed.
To cancel the function
- By moving the control from position « LIMIT » to position 0.
- By stopping the engine. The speed chosen previously is memorised.
In the event of a malfunction, a message appears, accompanied by a sound signal.
Contact a CITROËN dealer.
A fl oor mat not approved by CITROËN may risk sliding forward under the accelerator pedal and preventing you from pressing beyond the tight spot. It will then be impossible to exit the speed limitation, except by actioning the control under the steering wheel.
The driver must remain attentive and keep complete control of the vehicle.

16R A D I O M O D E
RADIO RECEPTION
Your audio system will be subject to certain phenomena that are not encountered by domestic systems. The reception of AM and FM signals is subject to interference which is caused by the nature and propagation of the signals, and is not a fault of your audio system.In AM mode, the reception may be affected when passing under power lines or bridges, or when travelling through tunnels.In FM mode, the reception may be affected by the distance from the station transmitter, the refl ecting of signals off obsta cles (mountains, hills, tower blocks) and radio blackspots (no coverage from the station transmitter).
SELECTING RADIO MODE
If the system is not already in radio mode, press button (C).
SELECTING A WAVEBAND AND MEMORY BANK
Press button (C), to go through the memory banks FM1, FM2 and FM3, for the FM waveband, and the memory bank MW/LW, for the AM waveband.
AUTOMATIC SEARCH (Automatic search mode activated)
Press either button (I) or (G) briefl y to tune into the following or preceding radio stations respectively, within the chosen wave band.By keeping either button (I) or (G) pressed down, the search mode will proceed through the waveband and will stop at the fi rst station it comes across once the button is released.The automatic search mode can also be operated using buttons (2) and (3) on the control at the steering wheel (P).It is possible to carry out a manual search to fi nd a known station if the automatic search is unable to tune into it (for example, due to very weak reception).
MANUAL SEARCH (Manual search mode activated)
To select the manual search mode, briefl y press the button “MAN” (H).The display indicates “MN” followed by the frequency.By keeping either button (I) or (G) pressed down, the search mode will proceed through the waveband and will stop on the frequency shown on the display when the button is released. The system will remain on the frequency displayed.The system will automatically return to the automatic search mode after several seconds, or by pressing the button “MAN” (H).
TUNING SENSITIVITY
Automatic searches can be carried out according to two levels of sensitivity.- to pick up the strongest radio signals, select the local tuning function “LO”.- to pick up signals which are weaker or further away, select the distance tuning function “DX”.The searches are fi rst carried out for the local sensitivity function “LO”, then the distance sensitivity function “DX”.To immediately initiate a distance sensitivity search “DX”, press either button (I) or (G) twice in a row.

26R A D I O M O D E
RADIO RECEPTION
Your audio system will be subject to certain phenomena that are not encountered by domestic systems. The reception of AM and FM signals is subject to interference which is caused by the nature and propagation of the signals, and is not a fault of your audio system.
In AM mode, the reception may be affected when passing under power lines or bridges, or when travelling through tunnels.
In FM mode, the reception may be affected by the distance from the station transmitter, the refl ecting of signals off obstacles (mountains, hills, tower blocks) and radio blackspots (no coverage from the station transmitter).
SELECTING RADIO MODE
If the system is not already in radio mode, press button (I).
SELECTING A WAVEBAND AND MEMORY BANK
Press button (D), to go through the memory banks FM1, FM2 and FM3, for the FM waveband, and the memory bank MW/LW, for the AM waveband.
AUTOMATIC SEARCH (Automatic search mode activated)
Press either button (G) or (E) briefl y to tune into the following or preceding radio stations respectively, within the chosen waveband.
By keeping either button (G) or(E) pressed down, the search mode will proceed through the waveband and will stop at the fi rst station it comes across once the button is released.
The automatic search mode can also be operated using buttons (2) and (3) on the control at the steering wheel (P).
It is possible to carry out a manual search to fi nd a known station if the automatic search is unable to tune into it (for example, due to very weak reception).
MANUAL SEARCH (Manual search mode activated)
To select the manual search mode, briefl y press the button “MAN” (F).
The display indicates “MN” followed by the frequency.
By keeping either button (G) or (E) pressed down, the search mode will proceed through the waveband and will stop on the frequency shown on the display when the button is released. The system will remain on the frequency displayed.
The system will automatically return to the automatic search mode after several seconds, or by pressing the button “MAN” (F).
TUNING SENSITIVITY
Automatic searches can be carried out according to two levels of sensitivity.
The searches are fi rst carried out for the local sensitivity function “LO”, then the distance sensitivity function “DX”.