wheel DACIA DUSTER 2009 1.G Heating And Air Conditioning User Guide

Downloaded from www.Manualslib.com manuals search engine 61A-29
HEATING
Control panel: Removal - Refitting
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer (see Fault finding - Re-
placement of components) (88C, Airbags and pre-
tensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and pre-
tensioners),
-the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly),
-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (84A, Control - Signals),
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),
-the storage compartment,
-the radio (see Radio: Removal - Refitting) (86A,
Instrument panel),
-the dashboard (see Dashboard: Removal - Refit-
ting) (57A, Interior equipment).
aPlace:
-the air mixing control to the hottest position,
-the air distribution control to the air vent position on
the dashboard,
-the air recirculation switch to the air recirculation
position.
aDisconnect the climate control panel connector .II - REMOVAL OPERATION
aFor the air mixing cable (10) , remove:
-the sheath stop by moving the tab (11) to one side,
-the control panel cable at (12) .
aFor the air distribution control cable (13) , remove:
-the sheath stop by moving the tab (14) to one side,
-the control panel cable at (15) .
aFor the air recirculation cable (16) , remove:
-the sheath stop by moving the tab (17) to one side,
-the control panel cable at (18) .
aRemove the climate control control panel.
REFITTING
aProceed in the reverse order to removal.
aCheck that the controls can be moved to their fullest
extent.
aUnlock the airbag computer (see Fault finding - Re-
placement of components) (88C, Airbags and
pretensioners). H79
125537

Downloaded from www.Manualslib.com manuals search engine 62A-12
AIR CONDITIONING
Compressor: Removal - Refitting
AIR CONDITIONING
62A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDrain the coolant circuit using the refrigerant
charging station (see Refrigerant circuit: Drain-
ing - Filling) .
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).aRemove:
-the front bumper (see Front bumper: Removal -
Refitting) and (see Exterior body front trim as-
sembly: Exploded view) (55A, Exterior protec-
tion),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the accessories belt (see Accessories belt: Re-
moval - Refitting) (11A, Top and front of engine).
II - REMOVAL OPERATION
aRemove:
-the pipe retaining bracket bolt (1) on the compres-
sor,
-the pipe union bolts (2) on the compressor. Equipment required
refrigerant charging station
Tightening torquesm
compressor bolts21 N.m
pipe union bolts8 N.m
pipe retaining bracket
bolt on the compressor21 N.m
IMPORTANT
Consult the safety instructions and cleanliness
advice and the operation recommendations before
carrying out any repairs (see Air conditioning:
Precautions for repair).
WARNING
To prevent moisture from entering the system,
place plugs on the cold loop components which are
open to the air.
Note:
Use blanking plugs for the fuel circuits with part
numbers 77 01 208 229 or 77 01 476 857 to plug
any openings exposed to the open air. They must
be clean. Do not use any which have already been
used to plug a fuel circuit.
WARNING
Consult the device's operating manual to avoid
incorrect use.
K4M
145190