belt DACIA DUSTER 2009 1.G Heating And Air Conditioning Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 61A-20
HEATING
Distribution unit: Removal - Refitting
61A
III - FINAL OPERATION
aRefit the floor carpet.
aConnect the heating resistor connector.
aRefit:
-the heating resistor relay mounting,
-the heating resistor relay mounting bolt.
aClip on:
-the starter switch connector on its mounting.
-the wiring at (6) .
aClip:
-the wiring on the distribution unit at (5) ,
-the wiring at (4) .
aRefit:
-the steering column (see Steering column: Re-
moval - Refitting) (36A, Steering assembly),
-the front air distribution ducts (see 61A, Heating,
Front air distribution duct: Removal - Refitting,
page 61A-9) ,
-the dashboard (see Dashboard: Removal - Refit-
ting) (57A, Interior equipment),
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),
-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (84A, Control - Signals),
-the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly),
-the radio (see Radio: Removal - Refitting) (86A,
Radio),
-the storage compartment,
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and seat
belt pretensioners).
aConnect the heater hoses.
aRefit the clips on the heater hoses.aRemove the hose clamps (Ms. 583).
aReplace the seals.
aLubricate the seals using recommended air condi-
tioning oil to make fitting easier.
aFit the pipe unions on the expansion valve.
aRefit the pipe union bolts on the expansion valve.
aPosition the engine compartment bulkhead sound-
proofing.
aConsult the refrigerant and oil quantity values before
filling the circuit (see 62A, Air conditioning, Air
conditioning: Parts and consumables for the re-
pair, page 62A-9) .
aFill the refrigerant circuit using the refrigerant
charging station (see Refrigerant circuit: Drain-
ing - Filling) .
aCheck for leaks (see Refrigerant circuit: Check) .
aCheck that the air conditioning is operating correctly
(see Air conditioning: Check) .
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aUnlock the airbag computer (see Fault finding - Re-
placement of components) (88C, Airbags and pre-
tensioners).
aFill the cooling circuit (see Cooling system: Drain-
ing - Refilling) (19A, Cooling).
aBleed the cooling circuit (see Cooling system:
Draining - Refilling) (19A, Cooling).
aCheck the cooling circuit (see Engine cooling sys-
tem: Check) (19A, Cooling). Note:
Check that the floor carpet reaches under the
accelerator pedal end-stop.
DIESEL VEHICLE
AIR CONDITIONING

Downloaded from www.Manualslib.com manuals search engine 61A-23
HEATING
Heater matrix: Removal - Refitting
LEFT-HAND DRIVE
61A
II - REFITTING OPERATION
aRefit the heater matrix.
aRefit:
-the heater matrix,
-the heater matrix bolts.
aPosition the heater matrix pipes on the heater ma-
trix.
aRefit the heater matrix pipe clips.
III - FINAL OPERATION
aRefit:
-the strut,
-the two lower bolts on the strut, respecting the
marking made during the removal operation,
-the two upper nuts to the strut,
aTorque tighten:
-the upper nuts of the strut (21 N.m),
-the lower bolts of the strut (21 N.m).
aPosition the floor carpet.
aConnect the heating resistor connector.
aRefit:
-the heating resistor relay mounting,
-the heating resistor relay mounting bolt.
aClip on:
-the starter switch connector on its mounting.
-the wiring onto the strut.
aClip the wiring onto the strut.
aRefit:
-the dashboard (see Dashboard: Removal - Refit-
ting) (57A, Interior equipment),
-the radio (see Radio: Removal - Refitting) (86A,
Radio),
-the storage compartment,-the instrument panel (see Instrument panel: Re-
moval - Refitting) (83A, Instrument panel),
-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (84A, Control - Signals),
-the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly).
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (88C, Airbags and seat
belt pretensioners).
aFit the heater hoses.
aRefit the clips on the heater hoses.
aRemove the hose clamps (Ms. 583).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aFill the cooling circuit (see Cooling system: Drain-
ing - Refilling) (19A, Cooling).
aBleed the cooling circuit (see Cooling system:
Draining - Refilling) (19A, Cooling).
aCheck the cooling circuit (see Engine cooling sys-
tem: Check) (19A, Cooling).
aUnlock the airbag computer (see Fault finding - Re-
placement of components) (88C, Airbags and pre-
tensioners). H79
Note:
Check that the floor carpet reaches under the
accelerator pedal end-stop.

Downloaded from www.Manualslib.com manuals search engine 62A-12
AIR CONDITIONING
Compressor: Removal - Refitting
AIR CONDITIONING
62A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDrain the coolant circuit using the refrigerant
charging station (see Refrigerant circuit: Drain-
ing - Filling) .
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).aRemove:
-the front bumper (see Front bumper: Removal -
Refitting) and (see Exterior body front trim as-
sembly: Exploded view) (55A, Exterior protec-
tion),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the accessories belt (see Accessories belt: Re-
moval - Refitting) (11A, Top and front of engine).
II - REMOVAL OPERATION
aRemove:
-the pipe retaining bracket bolt (1) on the compres-
sor,
-the pipe union bolts (2) on the compressor. Equipment required
refrigerant charging station
Tightening torquesm
compressor bolts21 N.m
pipe union bolts8 N.m
pipe retaining bracket
bolt on the compressor21 N.m
IMPORTANT
Consult the safety instructions and cleanliness
advice and the operation recommendations before
carrying out any repairs (see Air conditioning:
Precautions for repair).
WARNING
To prevent moisture from entering the system,
place plugs on the cold loop components which are
open to the air.
Note:
Use blanking plugs for the fuel circuits with part
numbers 77 01 208 229 or 77 01 476 857 to plug
any openings exposed to the open air. They must
be clean. Do not use any which have already been
used to plug a fuel circuit.
WARNING
Consult the device's operating manual to avoid
incorrect use.
K4M
145190