warning light DACIA LODGY 2014 Owner's Guide

JauneNoir Noir texte
2.19
ENG_UD33448_2
Frein à main / Direction assistée (X67 - X92 - Renault)
ENG_NU_975-6_X92_Dacia_2
Handbrake
To release
Pull lever 1 up slightly, press button 2
and then lower the lever to the floor.
The red warning light on the instrument
panel will come on if you are driving
with an incorrectly released handbrake.
HANDBRAKE/POWER-ASSISTED STEERING
To apply
Pull lever 1 upwards and make sure the
vehicle is immobilised.
Depending on the gradient
and/or vehicle load, it may
be necessary when station-
ary to apply the brake by
at least a further two notches and
engage a gear (1
st or reverse gear).
Never switch off the igni-
tion when travelling down-
hill, and avoid doing so in
normal driving (assistance
is not provided).
Make sure that the hand-
brake is properly released
when driving (red indicator
light off), otherwise over-
heating, or even damage, may
occur.
1
2
Power-assisted steering
With the engine running, do not leave
the steering wheel at full lock while sta-
tionary as this may damage the power-
assisted steering pump.
With the engine switched off, or if there
is a system fault, it is still possible to
turn the steering wheel. The force re-
quired will be greater.

JauneNoir Noir texte
2.20
ENG_UD33476_2
Dispositifs de correction et d’assistance à la conduite (X92 - Re\
nault)
ENG_NU_975-6_X92_Dacia_2
DRIVER CORRECTION DEVICES/AIDS (1/3)
ABS (anti-lock braking
system)
Under heavy braking, the ABS prevents
the wheels from locking, allowing the
stopping distance to be managed and
keeping control of the vehicle.
Under these circumstances, the vehi-
cle can be steered to avoid an obstacle
whilst braking. In addition, this system
can increase stopping distances, par-
ticularly on roads with low surface grip
(wet ground etc.).
You will feel a pulsation through the
brake pedal each time the system is
activated. The ABS does not in any
way improve the vehicle’s physical per-
formance relating to the road surface
and road-holding. It is still essential to
follow the rules of good driving practice
(such as driving at a safe distance from
the vehicle in front, etc.). Operating faults:
– If the
x warning light on the in-
strument panel comes on while driv-
ing, braking is still operational ;
– If the
x and D warning
lights on the instrument panel come
on when driving, this indicates a
fault with the braking system.
In this case, ABS, ESC and emergency
braking assist are also deactivated.
Consult an approved dealer.
Depending on the vehicle, this is com-
posed of:
– of the ABS (anti-lock braking
system);
– of the electronic stability control
ESC with understeer control and
traction control ASR;
– emergency brake assist with, de- pending on the vehicle, braking
anticipation;
In an emergency, apply firm and
continuous pressure to the brake
pedal. There is no need to pump
it repeatedly. The ABS will modu-
late the force applied in the braking
system.
These functions are an ad-
ditional aid in the event of
critical driving conditions,
enabling the vehicle behav-
iour to be adapted to suit the driving
conditions.
However, the functions do not take
the place of the driver. They do
not increase the vehicle’s limits
and should not encourage you
to drive more quickly. Therefore,
they can under no circumstances
replace the vigilance or responsibil-
ity of the driver when manoeuvring
the vehicle (the driver must always
be ready for sudden incidents which
may occur when driving).
Your braking systems
are partially operational.
However, it is dangerous
to brake suddenly and
it is essential to stop immediately,
as soon as traffic conditions allow.
Contact an approved dealer.

JauneNoir Noir texte
2.21
ENG_UD33476_2
Dispositifs de correction et d’assistance à la conduite (X92 - Re\
nault)
ENG_NU_975-6_X92_Dacia_2
DRIVER CORRECTION DEVICES/AIDS (2/3)
Electronic stability control
ESC with understeer control
and traction control ASR
Electronic stability control ESC
This system helps you to keep control
of the vehicle in critical driving condi-
tions (avoiding an obstacle, loss of grip
on a bend, etc.).
Operating principle
A sensor in the steering wheel detects
the direction selected by the driver.
Other sensors throughout the vehicle
measure the actual direction.
The system compares driver input to
the actual trajectory of the vehicle and
corrects the trajectory if necessary by
controlling the braking of certain wheels
and/or engine power. In the event that
the system is engaged, indicator light
 flashes on the instrument panel. Operating faults
When the system detects an operating
fault, the
 and/or  warning
lights on the instrument panel come on.
In this case, the ESC and ASR are de-
activated.
Consult an approved dealer.
Understeer control
This system optimises the action of the
ESC in the case of pronounced under-
steering (loss of front axle road hold-
ing).
Traction control ASR
This system helps to limit wheelspin of
the drive wheels and to control the ve-
hicle when pulling away accelerating or
decelerating.
Operating principle
Using the wheel sensors, the system
measures and compares the speed of
the drive wheels at all times and slows
down their over-rotation. If a wheel is
starting to slip, the system brakes au-
tomatically until the drive supplied be-
comes compatible with the level of grip
under the wheel again.
The system also adjusts the engine
speed to the grip available under the
wheels, independently of the pressure
exerted on the accelerator pedal.

JauneNoir Noir texte
2.22
ENG_UD33476_2
Dispositifs de correction et d’assistance à la conduite (X92 - Re\
nault)
ENG_NU_975-6_X92_Dacia_2
DRIVER CORRECTION DEVICES/AIDS (3/3)
The traction control ASR offers addi-
tional safety, it is recommended that
you do not drive with the function disa-
bled. Correct this as soon as possible
by pressing switch 1 again.
Note: The function is reactivated auto-
matically when the ignition is switched
on or when a speed of approximately
30 mph (50 km/h) is exceeded.
Emergency brake assist
This is an additional system to ABS
which helps reduce vehicle stopping
distances.
Operating principle
The system detects an emergency
braking situation. In this case, the brak-
ing assistance immediately develops
maximum power and may trigger ABS
regulation.
ABS braking is maintained as long as
the brake pedal is not released.
Hazard warning lights switching on
Depending on the vehicle, these may
light up in the event of sudden decel-
eration.
Operating faults
When the system detects an operating
fault, the warning light
x is dis-
played on the instrument panel.
Consult an approved dealer.
Braking anticipation
Depending on the vehicle, when you
rapidly release the accelerator, the
system anticipates the braking ma-
noeuvre in order to reduce stopping
distances.
Disabling the function ASR
In some situations (driving on very wet
ground: snow, mud, etc. or driving with
snow chains fitted), the system may
reduce the engine output to limit wheel-
spin. If this is not required, it is possible
to deactivate the function by pressing
switch
1. In this case, the warning light
 comes on, on the instrument
panel. This action does not deactivate
the ESC.
1

JauneNoir Noir texte
2.25
ENG_UD33070_3
Régulateur-limiteur de vitesses : fonction limiteur (X92 - Renault)\
ENG_NU_975-6_X92_Dacia_2
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3)
Switching off the function
The speed limiter function is deac-
tivated if you press switch 1 : in this
case a speed is no longer stored. The
orange instrument panel warning light
 goes out, confirming that the func-
tion is stopped.
Putting the function on
standby
The speed limiter function is suspended
when you press switch 5 (O). In this
case, the limit speed remains stored
and the message “MEM” accompanied
by this speed appears on the instru-
ment panel.
Recalling the limit speed
If a speed has been saved, it can be re-
called by pressing switch 4 ((R)).
2451
3
When the speed limiter is put on
standby, pressing switch 2 (+) re-
activates the function without taking
into account the stored speed: it is
the speed at which the vehicle is
moving that is taken into account.

JauneNoir Noir texte
2.27
ENG_UD33494_1
Régulateur-limiteur de vitesse : fonction régulateur (X92 - Dacia\
)
ENG_NU_975-6_X92_Dacia_2
Driving
Once a cruising speed is stored and
the cruise control function is active,
you may lift your foot off the accelera-
tor pedal.
Important: you are never-
theless advised to keep
your feet close to the pedals
in order to react if neces-
sary.
Activating cruise control
At a steady speed (above 18 mph
(30 km/h approximately)) press switch 2
or (+): the function is activated and the
current speed is saved.
The cruising speed replaces the
dashes and the cruise control is con-
firmed by the appearance of the mes-
sage “CRUISE" and the warning light 6
 being lit green, as well as the warn-
ing light 7
.
Switching on
Press switch 1 side .
The warning light 6 comes on, lit green,
and the message “CRUISE” appears
on the instrument panel, accompanied
by dashes to indicate that the cruise
control function is activated and waiting
to store a cruising speed.
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4)
1
67
23

JauneNoir Noir texte
2.29
ENG_UD33494_1
Régulateur-limiteur de vitesse : fonction régulateur (X92 - Dacia\
)
ENG_NU_975-6_X92_Dacia_2
Switching off the function
The cruise control function is deacti-
vated if you press switch 1: in this case
a speed is no longer stored. The two in-
strument panel warning lights
 and
 go out to confirm that the function is
deactivated.
Returning to the cruising speed
If a speed is stored, it can be recalled,
once you are sure that the road con-
ditions are suitable (traffic, road sur-
face, weather conditions, etc.). Press
switch
4 (R) if the vehicle speed is
above 20 mph (30 km/h).
When the stored speed is recalled, acti-
vation of the cruise control is confirmed
by the illumination of the
 warning
light.
NB: if the speed previously stored is
much higher than the current speed,
the vehicle will accelerate more rapidly
to reach this threshold.
When the cruise control function is
put on standby, pressing switch 2
(+) reactivates the cruise control
function without taking into account
the stored speed: it is the speed at
which the vehicle is moving that is
taken into account.
Putting the function on
standby
The function is set to standby if you:
– use the switch 5 (O);
– the brake pedal;
– the clutch pedal;
In all three cases, the cruising speed re-
mains stored and the message “MEM”
appears on the instrument panel.
Standby is confirmed by warning light
 going out.
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4)
Putting the cruise control
on standby or switching it
off does not cause a rapid
reduction in speed: you
must brake by depressing the brake
pedal.
23541

JauneNoir Noir texte
2.31
ENG_UD28035_2
Aide au parking (X92 - Renault)
ENG_NU_975-6_X92_Dacia_2
Deactivating the system
You can deactivate the system by
pressing switch 1.
The warning light built into the switch
remains lit constantly.
The deactivated system can be reacti-
vated by pressing the switch again.
PARKING DISTANCE CONTROL (2/2)
1
Operating faults
When the system detects an operating
fault, there will be a three-second con-
tinuous beep as a warning. Please con-
sult an authorised dealer.

JauneNoir Noir texte
5.6
ENG_UD33465_1
Kit de gonflage des pneumatiques (X67 - X92 - Dacia)
ENG_NU_975-6_X92_Dacia_5
TYRE INFLATION KIT (2/6)
Inflation kit C
Depending on the vehicle, in the event
of a puncture, use the kit C located in
the boot.
Before using this kit, park
the vehicle at a sufficient
distance from traffic, switch
on the hazard warning
lights, apply the handbrake, ask all
passengers to leave the vehicle and
keep them away from traffic.
Open the kit, remove caps 1 and 3 (it is
essential not to remove the cap from
the bottle) then screw bottle 2 to its
base 3.
With the engine running and the
handbrake applied,
– unscrew the valve cap on the wheel concerned and screw the inflation
adapter 6 onto valve;
– connect adapter 8 to accessories
socket 9 on the dashboard of the ve-
hicle;
9
1234
5
6
78
C
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.

JauneNoir Noir texte
5.9
ENG_UD33465_1
Kit de gonflage des pneumatiques (X67 - X92 - Dacia)
ENG_NU_975-6_X92_Dacia_5
With the engine running and the
handbrake engaged:
– unroll the hose from the container;
– connect the compressor hose 13 to
the container inlet 18;
– depending on the vehicle, connect the container 18 to the compressor
from the container recess 17;
– unscrew the valve cap on the rel- evant wheel and screw on the con-
tainer’s inflation adapter 11;
– adapter 12 must be connected to
the vehicle accessories socket;
– press switch 14 to inflate the tyre to the recommended pressure (please
refer to the information on “Tyre
pressure”); – after a maximum of 15 minutes, stop
inflating and read the pressure (on
pressure gauge 15).
Note: while the container is empty-
ing (approximately 30 seconds), the
pressure gauge 15 will briefly indi-
cate a pressure of up to 6 bar. The
pressure will then drop.
– adjust the pressure: to increase it, continue inflation with the kit; to
reduce it, press button 16.
If a minimum pressure of 1.8 bar is
not reached after 15 minutes, repair
is not possible; do not drive the ve-
hicle but contact an approved dealer.
TYRE INFLATION KIT (5/6)
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.
Before using this kit, park
the vehicle at a sufficient
distance from traffic, switch
on the hazard warning
lights, apply the handbrake, ask all
passengers to leave the vehicle and
keep them away from traffic.
Inflation kit D
Depending on the vehicle, in the event
of a puncture, use the kit D located in
the boot or underneath the boot carpet.
1112
13
14
15
17
18
D
16