remove DACIA LODGY 2016 User Guide

JauneNoir Noir texte
2.13
ENG_UD34407_2
Conseils entretien et antipollution (X98 - X87 - X07 - Renault)
ENG_NU_975-6_X92_Dacia_2
MAINTENANCE AND ANTIPOLLUTION ADVICE
Your vehicle complies with criteria for
recycling and recovering vehicles at the
end of their service life which will come
into force in 2015.
Some parts of your vehicle have there-
fore been designed to facilitate future
recycling.
These parts are easy to remove so
that they can be recovered and reproc-
essed by recycling companies.
By virtue of its design, moderate fuel
consumption and initial settings, your
vehicle also conforms to current anti-
pollution regulations. The manufac-
turer is actively striving to reduce pol-
lutant exhaust gas emissions and to
save energy. But the fuel consumption
of your vehicle and the level of pollutant
exhaust gas emissions are also your
responsibility. Ensure that it is main-
tained and used correctly.
Maintenance
It is important to remember that fai-
lure to respect antipollution regulations
could lead to legal action being taken
against the vehicle owner. In addition, replacing engine, fuel
supply system and exhaust compo-
nents with parts other than those origi-
nally recommended by the manufactu-
rer may alter your vehicle so that it no
longer complies with antipollution regu-
lations.
Have your vehicle adjusted and
checked by an approved Dealer, in ac-
cordance with the instructions given in
your maintenance schedule: they will
have all the equipment necessary for
ensuring that your vehicle is maintained
to its original standard.
Engine adjustments
– Spark plugs:
for optimum condi-
tions of use, output and performance
the specifications laid down by our
Design Department must be strictly
applied.
If the spark plugs have to be changed, use the make, type and gap specified
for your vehicle’s engine. Contact an
authorised dealer for this.
– Air filter: a choked element will reduce efficiency. It must be re-
placed.
– Ignition and idle speed: no adjust-
ment is needed.
Exhaust gas monitoring
system
The exhaust gas monitoring system will
detect any operating faults in the vehi-
cle’s antipollution system.
If this system malfunctions, toxic sub-
stances may be released into the at-
mosphere or damage may occur.
ÄThis warning light on the in-
strument panel will indicate if
there are any faults in the system:
This lights up when the ignition is
switched on and goes out when the
engine is started.
– If it lights up continuously, consult an approved Dealer as soon as pos-
sible;
– if it flashes, reduce the engine speed until the light stops flashing. Contact
your approved dealer as soon as
possible.

JauneNoir Noir texte
2.14
ENG_UD34481_2
Environnement (sans marque) (X35 - X44 - X45 - X77 - X81 - X85 - X90 \
- X91 - X83 - X61 - TEST - X95 - L90 Ph2 - F90 Ph2 - R90 Ph2 - X33 - X47 - X43 - X38 - H79 -
ENG_NU_975-6_X92_Dacia_2
ENVIRONMENT
Emissions
Your vehicle has been designed to emit
fewer greenhouse gases (CO2) while in
use, and therefore to consume less fuel
(eg. 140 g/km, equivalent to 5.3 l/100
km for a diesel vehicle).
Our vehicles are also equipped with a
particle filter system including a cata-
lytic converter, an oxygen sensor and
an active carbon filter (the latter pre-
vents vapour from the fuel tank being
released into the open air).
For certain diesel vehicles, this system
also has a particle filter to reduce the
volume of soot particles emitted.
Please make your own
contribution towards
protecting the environment
too
– Worn parts replaced in the course of
routine vehicle maintenance (vehi-
cle battery, oil filter, air filter, batter-
ies, etc.) and oil containers (empty or
filled with used oil) must be disposed
of through specialist organisations. – At the end of the vehicle’s service
life, it should be sent to approved
centres to ensure that it is recycled.
– In all cases, comply with local legis- lation.
Recycling
Your vehicle is 85% recyclable and
95% recoverable.
To achieve these objectives, many of
the vehicle components have been de-
signed to enable them to be recycled.
The materials and structures have
been carefully designed to allow these
components to be easily removed and
reprocessed by specialist companies.
In order to preserve raw material re-
sources, this vehicle incorporates nu-
merous parts made from recycled plas-
tics or renewable materials (vegetable
or animal-derived materials such as
cotton or wool).
Your vehicle has been designed with
respect for the environment in mind for
its entire service life: during production,
use and at the end of its life.
This commitment is illustrated by the of
the manufacturer eco² signature.Manufacture
Your vehicle has been manufactured at
a factory which complies with a policy
to reduce the environmental impact
on the surrounding areas (reduction of
water and energy consumption, visual
and noise pollution, atmospheric emis-
sions and waste water; sorting and re-
using waste).

JauneNoir Noir texte
3.3
ENG_UD24439_1
Aérateurs, sorties air (X92 - Renault)
ENG_NU_975-6_X92_Dacia_3
AIR VENTS, air outlets (2/2)
Centre and side air vents
Air flow
To open air vent 9, press on the air vent
(point 10) until it is open as far as re-
quired.
Direction
To direct the air flow, swivel side air
vent 9.
10
999
Do not add anything to the
vehicle’s ventilation circuit
(for example, to remove
bad odours).
There is a risk of damage or of
fire.
To remove bad odours from your ve-
hicles, only use the systems designed
for this purpose. Consult an approved
Dealer.
10

JauneNoir Noir texte
3.17
ENG_UD28017_3
Appuis-tête arrière (X92 - Renault)
ENG_NU_975-6_X92_Dacia_3
REAR HEADRESTS (1/2)
Position for using headrest A
Lift the headrest to maximum height,
then lower it until it locks.
To raise the headrest A
Raise the headrest as far as it will go,
then press tab(s) 1 and remove the
headrest.
The headrest is a safety
component. Ensure that it is
fitted and in the correct po-
sition: the top of your head
should be in line with the top of the
headrest.
11
To put the headrest back in
place A
Insert the rods into the holes, press the
tab(s) 1 and lower the headrest.
Headrest A storage
position B
Press tab 1 and lower the headrest fully.
When the headrest is set at the
lowest position , Bthis is for storage
only: it should not be in this position
when a seat is occupied.
AAA
BBB
AA

JauneNoir Noir texte
3.18
ENG_UD28017_3
Appuis-tête arrière (X92 - Renault)
ENG_NU_975-6_X92_Dacia_3
To adjust the height of the
headrest C
(depending on vehicle)
Press lock tab 2 and simultaneously
slide the headrest to the required po-
sition.
To raise the headrest C
Press lock tab 2 and remove the head-
rest.
To put the headrest back in
place C
Insert the rods into the holes, press lock
tab 2 and lower the headrest.
The headrest is a safety
component. Ensure that it is
fitted and in the correct po-
sition: the top of your head
should be in line with the top of the
headrest.
REAR HEADRESTS (2/2)
C
2

JauneNoir Noir texte
3.21
ENG_UD26885_2
Sièges arrière de deuxième rangée: fonctionnalité (X92 -\
Renault)
ENG_NU_975-6_X92_Dacia_3
REAR SEAT FUNCTIONS: second row (3/3)
Accessing the third row rear
seats
– Lower handle 2;
– lower the seatback onto the seat base;
– raise the seat until vertical.
To put the seat back into its initial po-
sition, perform the same procedure in
reverse.Restriction of use
If a passenger is occupying one of
the second row seats, do not drive
with the other second row seat
folded down.
Make sure that the seat-
back is correctly locked. If
necessary, remove any ob-
stacles behind the seats.
Repeat the above until the seat is
locked correctly.To avoid all risk of injury,
ensure that nobody is close
to the moving parts.
2
When refitting the seat-
back, make sure it is cor-
rectly locked in place.
If seat covers are fitted ,
make sure these do not prevent the
seatback latch from locking in.
Make sure that the seat belts are
positioned correctly.
Reposition the headrests.

JauneNoir Noir texte
3.22
ENG_UD34862_4
Sièges arrière de troisième rangée: fonctionnalité (X92 \
- Renault)
ENG_NU_975-6_X92_Dacia_3
REAR SEAT FUNCTIONS: third row (1/3)
The third row rear seats can be folded
down or removed for transporting bulky
objects.To fold down the seats
– Ensure that the rear seat belts are
correctly positioned on the hooks 1;
– lower the headrests (refer to the in- formation on the “Rear headrests” in
Section 3);
– unlock controls 2, press on the
middle of the seat backs and lower
the seatbacks onto the base;
– pull the strap 3 to release the bench
seat and lift the seat base until it is
vertical.
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
Check that the rear seat
belts are positioned and
operating correctly each
time the rear bench seat is
moved.
1
Ensure that the strap 3 is securely
fixed in its meal ring 4 . Risk of
damage.
3
2
3
4

JauneNoir Noir texte
3.24
ENG_UD34862_4
Sièges arrière de troisième rangée: fonctionnalité (X92 \
- Renault)
ENG_NU_975-6_X92_Dacia_3
To remove the seats
– Ensure that the rear seat belts are
correctly positioned on the hooks 1;
– lower the headrests (refer to the in- formation on the “Rear headrests” in
Section 3);
– unlock controls 2, press on the
middle of the seat backs and lower
the seatbacks onto the base;
– pull strap 3 to release and lift the
seat base until it is vertical;
– unlock controls 6;
– lift the seats to either remove them or to group them together with the
second row.
To install seats
– Ensure that the rear seat belts are correctly positioned on the hooks 1;
– reposition the seats with the roof hooks 7;
– Lower the seat base until it locks in position;
– unlock controls 2 and raise the seat backs using strap 5;
– Make sure that the seat base and seatbacks lock into position cor-
rectly.
3
3
Ensure that the strap 3 is securely
fixed in its meal ring 4 . Risk of
damage.
4
7
6
When moving the rear
seats, check that the an-
choring points are clean
(they must be free from grit,
cloths, toys, etc.)
2
11
REAR SEAT FUNCTIONS: third row (3/3)
5

JauneNoir Noir texte
3.26
ENG_UD26647_2
Mise en cinéma des sièges arrière (X92 - Renault)
ENG_NU_975-6_X92_Dacia_3
REAR SEAT FUNCTIONS: grouping of seats (2/3)
To group together the two
rows of rear seats
Fold down the second row rear seats.
Refer to the information on the “Second
row rear seats” in Section 3.
Remove the third row rear seats Refer
to the information on the “Third row rear
seats” in Section 3.
Return the third row rear seats (seat
forwards and headrest upwards).
Position them against the second row
rear seats, with the hook 1 on the bar 2.
Fold down the third row rear seats
against the second row rear seats.Take the adjustable attachment straps
3
out of the storage pockets 5 and pass
them around the front headrest rods 4.
Pull on the attachment straps 3 to
ensure everything is attached.
For safety reasons, carry
out any adjustments when
the vehicle is stationary.
The third row bench seat
is quite heavy. For your own safety,
please handle carefully.
1
2
3
5
4

JauneNoir Noir texte
3.27
ENG_UD26647_2
Mise en cinéma des sièges arrière (X92 - Renault)
ENG_NU_975-6_X92_Dacia_3
REAR SEAT FUNCTIONS: grouping of seats (3/3)
To reposition the seats
Loosen and remove the attachment
straps 3 from the front headrest and
store them in the storage pockets 5.
Lift and release the third row rear seats.
Return the third row rear seats (seat
downwards, headrest upwards) and
bring them back towards the rear. Replace the third row rear seats in po-
sition. Refer to the information on the
“Third row rear seats” in Section 3.
Reposition the second row rear seats.
Refer to the information on the “Second
row rear seats” in Section 3.
For safety reasons, carry
out any adjustments when
the vehicle is stationary.
The third row bench seat
is quite heavy. For your own safety,
please handle carefully.
3
5