brake DACIA LODGY 2017 Owner's Manual
[x] Cancel search | Manufacturer: DACIA, Model Year: 2017, Model line: LODGY, Model: DACIA LODGY 2017Pages: 220, PDF Size: 2.62 MB
Page 161 of 220

JauneNoir Noir texte
5.9
ENG_UD33465_1
Kit de gonflage des pneumatiques (X67 - X92 - Dacia)
ENG_NU_975-6_X92_Dacia_5
With the engine running and the
handbrake engaged:
– unroll the hose from the container;
– connect the compressor hose 13 to
the container inlet 18;
– depending on the vehicle, connect the container 18 to the compressor
from the container recess 17;
– unscrew the valve cap on the rel- evant wheel and screw on the con-
tainer’s inflation adapter 11;
– adapter 12 must be connected to
the vehicle accessories socket;
– press switch 14 to inflate the tyre to the recommended pressure (please
refer to the information on “Tyre
pressure”); – after a maximum of 15 minutes, stop
inflating and read the pressure (on
pressure gauge 15).
Note: while the container is empty-
ing (approximately 30 seconds), the
pressure gauge 15 will briefly indi-
cate a pressure of up to 6 bar. The
pressure will then drop.
– adjust the pressure: to increase it, continue inflation with the kit; to
reduce it, press button 16.
If a minimum pressure of 1.8 bar is
not reached after 15 minutes, repair
is not possible; do not drive the ve-
hicle but contact an approved dealer.
TYRE INFLATION KIT (5/6)
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.
Before using this kit, park
the vehicle at a sufficient
distance from traffic, switch
on the hazard warning
lights, apply the handbrake, ask all
passengers to leave the vehicle and
keep them away from traffic.
Inflation kit D
Depending on the vehicle, in the event
of a puncture, use the kit D located in
the boot or underneath the boot carpet.
1112
13
14
15
17
18
D
16
Page 164 of 220

JauneNoir Noir texte
5.12
ENG_UD34859_3
Changement de roue (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
Place the jack 4 horizontally; the jack
head must be lined up with the sill 1
closest to the wheel concerned, as
shown by arrow 2.
Crank up the jack 4 by hand at first to
align the base plate (which should be
inclined further inwards than the jack
head).
Turn the wheelbrace until the wheel lifts
off the ground.
CHANGING A WHEEL (1/2)
Vehicles equipped with a jack
and wheelbrace
If necessary, remove the hubcap.
Use the wheelbrace 3 to slacken off
the wheel bolts. Fit it so that you press
downwards rather than pulling up-
wards.
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.
To prevent any risk of injury
or damage to the vehicle,
only crank the jack until the
wheel you are replacing is
a maximum of 3 centimetres off the
ground.
If the vehicle is not equipped with a
jack or wheelbrace, you can obtain
these from your approved dealer.Switch on the hazard warn-
ing lights.
Keep the vehicle away from
traffic and on a level surface
where it will not slip.
Apply the parking brake and engage
a gear (first or reverse).
Ask all passengers to leave the ve-
hicle and keep them away from traf-
fic.
1
23
4
Page 171 of 220

JauneNoir Noir texte
5.19
ENG_UD26662_2
Feux arrière: remplacement des lampes (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
REAR AND SIDE LIGHTS: changing bulbs (1/3)
Direction indicator, brake and
side lights
Undo bolt 1 to remove the light. Release the light assembly from out-
side the vehicle by pulling towards the
rear.
Remove the bulb holder
3 by releasing
clips 2.
Refitting
To refit, proceed in the reverse order,
taking care not to damage the wiring,
and fasten clips 2 on the bulb holder 3.4 Side light and brake light
Bulb type 4: P21/5W.
5 Indicator light
Bulb type 5: PY21W.
6
Reversing light (right-hand side
only)
Bulb type 6: P21W.
7 Fog light (left-hand side only)
Bulb type 7: P21W.
3
4
5
61
7
2
2
Page 172 of 220

JauneNoir Noir texte
5.20
ENG_UD26662_2
Feux arrière: remplacement des lampes (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
REAR AND SIDE LIGHTS: changing bulbs (2/3)
High-level brake light
– Remove the two plastic blanking
covers 6 from the inside.
– Unclip the light using a screwdriver, by releasing the metal clips from
their housings.
– Remove light from the outside. Replace the bulb without disconnect-
ing the wiring.
Bulb type 7: W16W.
Refitting
To return it, proceed in the reverse
order to removal.
Check the tabs are correctly locked in
position.
The bulbs are under pres-
sure and may break when
replaced.
Risk of injury.
7
6
Page 179 of 220

JauneNoir Noir texte
5.27
ENG_UD33424_3
Fusibles (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
FUSES (4/4)
Number Allocation
A Electric rear window
B Electric door mirrors
C Front electric window
1 LPG
2 Left-hand main beam
headlight
3 Right-hand main beam
headlight
4 Left-hand dipped beam
headlight
5 Right-hand dipped beam
headlight
6 Left-hand side lights
7 Right-hand side lights
8 Rear accessories socket
9 Rear fog lights
10 Horn
11 Automatic door lockingNumber Allocation
12 ESC
13 Courtesy light
14 ABS-ESC
15 Reverse gear, windscreen
wiper
16 Cruise control-Speed
limiter, rear windscreen,
unfastened seatbelt
warning, parking distance
control
17 Daytime running lights
18 Brake lights
19 Fuel pump, Injection
20 Airbag
21 Heated seats
22 Power-assisted steering
23 Location reserved for
additional equipment.
24 Direction indicator lightNumber Allocation
25 Passenger compartment
ECU
26 Passenger compartment
ECU
27
and 29 Steering column control
28 Not used
30 Location reserved for
additional equipment.
31 Instrument panel
32 Radio
33 Starter
34 Windscreen wiper
35 Passenger compartment
ventilation
36 Cigar lighter
37 Diagnostic socket
38 Defrosting rearview mirror
39 Front fog lights
Page 184 of 220

JauneNoir Noir texte
5.32
ENG_UD24482_1
Remorquage: dépannage (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
The steering wheel must be un-
locked and the ignition key must be
in position M (ignition on) to provide
brake lights and hazard warning
lights on the towed vehicle. At night
the vehicle must have its lights on.
Furthermore, it is essential to respect
the towing regulations set out in the leg-
islation of the country concerned and, if
your vehicle is the towing vehicle, not to
exceed the towing weight of your vehi-
cle. Contact an approved Dealer.
TOWING: breakdown (1/2)
When the engine is
stopped, steering and brak-
ing assistance are not op-
erational.Do not remove the key from
the ignition when the vehi-
cle is being towed.
Page 185 of 220

JauneNoir Noir texte
5.33
ENG_UD24482_1
Remorquage: dépannage (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
Only use the front 1 and rear 4
towing points.
These towing points may only be used
for towing: never use them for lifting the
vehicle directly or indirectly.Access to towing points
Unclip cover 3 or 5 by inserting a flat-
blade screwdriver or similar under the
cover.
Tighten towing hitch 2 fully: as much
as possible by hand at first, then finish
tightening it using the wheelbrace.
Use only towing hitch 2 and the wheel-
brace located under the luggage com-
partment carpet in the tool kit (please
refer to the information on the “Tool kit”
in Section 5).
– Use a rigid towing bar.
If a rope or cable is used
(where the law allows this),
the vehicle being towed
must be able to brake.
– A vehicle must not be towed if it is not fit to be driven.
– Avoid accelerating or braking suddenly when towing, as this
may result in damage being
caused to the vehicle.
– When towing a vehicle, it is ad- visable not to exceed 15 mph
(25 km/h).
Do not leave the tools unse-
cured inside the vehicle as
they may come loose under
braking.
TOWING: breakdown (2/2)
1
4
3
5
2
2
Page 187 of 220

JauneNoir Noir texte
5.35
ENG_UD33475_2
Accessoires VT (X35 - X44 - X45 - X77 - X81 - X85 - X90 - X91 - X70 - X76 - X83 - X61\
- TEST - X95 - X33 - X47 - X43 - X38 - H79 - X62 - X32 - X67 - X92 - X98 - X52 -
ENG_NU_975-6_X92_Dacia_5
ACCESSORIES
Electrical and electronic accessoriesBefore installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po-
sition of the aerial, etc.), make sure it is compatible with your vehic\
le. You can get advice from an authorised dealer.
Connect accessories with a maximum power of 120 watts only. Fire hazard.
No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorre\
ctly connecte d
system may result in damage being caused to the electrical equipment and\
/or the components connected to it.
If the vehicle is fitted with any aftermarket electrical equipment, make\
sure that the installation is correctly protected by a fuse.
Establish the rating and position of this fuse.
Use of transmission/receiving devices (telephones, CB equipment etc.).\
Telephones and CB equipment with integrated aerials may cause interference to the electronic systems originally fitted to the
vehicle: it is advisable only to use equipment with an external aerial. \
Furthermore, we remind you of the need to conform
to the legislation in force concerning the use of such equipment.
Fitting after-market accessoriesIf you wish to install accessories on the vehicle: please contact an aut\
horised dealer. Also, to ensure the correct operation o f
your vehicle, and to avoid any risk to your safety, we recommend that you use only accessories specifically designed for y\
our
vehicle, which are the only accessories for which the manufacturer will \
provide a warranty.
If you are using an anti-theft device, only attach it to the brake pedal\
.
Obstructions to the driver
On the driver’s side, only use mats suitable for the vehicle, attached with the pre-fi\
tted components, and check the fitting re gu-
larly. Do not lay one mat on top of another. There is a risk of wedging the pedals.
Page 198 of 220

JauneNoir Noir texte
6.6
ENG_UD33477_4
Masses (en kg) (X92 - Renault)
ENG_NU_975-6_X92_Dacia_6
WEIGHTS (in kg) (1/2)
The weights indicated are for a basic vehicle without options: they vary\
depending on the your vehicle’s equipment.
Consult an approved Dealer
Five-seater versions
Maximum permissible all-up weight (MMAC)
Gross Train Weight (MTR) Weights indicated on the manufacturer’s plate (refer
to Section 6 “Vehicle identification plate”)
Braked Trailer Weight* found by calculating: MTR- MMAC
Unbraked Trailer Weight* 580
Permissible nose weight* 75
Maximum permissible load on roof with a
carrying device 80 (including carrying equipment)
* Towing weight (towing a caravan, boat, etc.)
Towing is prohibited when the MTR - MMAC calculation is equal to zero, or\
when the MTR is equal to zero (or is not listed) on t he
identification plate.
– It is important to comply with the towing weights, governed by local leg\
islation in each country and, in particular, laid down in
the Road Traffic Regulations. Contact an approved Dealer about any towing equipment.
– When towing, under no circumstances may the total train weight (vehicle + trailer) be exceeded . However the following is
permitted: – rear axle MMTA exceeded by no more than 15%,
– maximum MMAC exceeded by no more than 10% or 100 kg (whichever is reach\
ed first).
In either case, the maximum speed of the vehicle and trailer must not ex\
ceed 60 mph (100 km/h) and the tyre pressures must be increased by 0.2 bar (3 PSI).
– The engine output and climbing capability are reduced with altitude. We recommend that the maximum load be reduced by 10% at an altitude of 1,000 metres and by an additional 10% for each 1,000 m\
etres thereafter.
Weight transfer on Estate versions (depending on local laws)
If the Maximum Authorised Mass of the vehicle has not been reached, up to 200 kg can be transferred to the braked trailer, with in
the limits of the Gross Train Weight.
Page 199 of 220

JauneNoir Noir texte
6.7
ENG_UD33477_4
Masses (en kg) (X92 - Renault)
ENG_NU_975-6_X92_Dacia_6
WEIGHTS (in kg) (2/2)
The weights indicated are for a basic vehicle without options: they vary\
depending on the your vehicle’s equipment.
Consult an approved dealer.
7-seater version
Maximum Permissible All-Up Weight (MMAC)
Total Train Weight (MTR) Weights indicated on the manufacturer’s plate (refer
to Section 6 “Vehicle identification plate”)
Braked Trailer Weight* obtained using the calculation: MTR - MMAC
Unbraked Trailer Weight* 630
Permissible nose weight* 75
Maximum permissible load on roof with a
carrying device 80 (including carrying equipment)
* Towing weight (towing a caravan, boat, etc.)
Towing is prohibited when the GTW - MAM calculation is equal to zero, or \
when the GTW is equal to zero (or is not listed) on th e
identification plate.
– It is important to comply with the towing weights, governed by local leg\
islation in each country and, in particular, laid down in
the Road Traffic Regulations. Contact an approved Dealer about any towing equipment.
– When towing, under no circumstances may the total train weight (vehicle + trailer) be exceeded . However the following is
permitted: – the Maximum permissible weight at the rear may be exceeded by no more th\
an 15%,
– the maximum permissible all-up weight may be exceeded by no more than 10\
% or 100 kg (whichever occurs first).
In either case, the maximum speed of the vehicle and trailer must not ex\
ceed 60 mph (100 km/h) and the tyre pressures must be increased by 0.2 bar (3 PSI).
– The engine output and climbing capability are reduced with altitude. We recommend that the maximum load be reduced by 10% at an altitude of 1,000 metres and by an additional 10% for each 1,000 m\
etres thereafter.
Weight transfer on Estate versions (depending on local laws)
If the Maximum Authorised Mass of the vehicle has not been reached, up to 200 kg can be transferred to the braked trailer, with in
the limits of the Gross Train Weight.