wheel DACIA LODGY 2021 Owner's Manual

JauneNoir Noir texte
5.2
ENG_UD28039_2
Outils (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
TOOLS
Accessing the toolsThe tools are located in the luggage
compartment.
The presence of the tools depends on
the vehicle.
Jack 1To use the jack, unscrew nut 5. When
replacing the jack, fold it up completely
and replace it in its housing. Tighten the
nut 5 to secure the jack.
Hubcap tool 2Removes the wheel hubcaps. Located
behind the jack.
Tow eye 3Please see “Towing: breakdown recov-
ery” in Section 5.
5
Never leave tools unsecured in the vehicle: there is a risk that they ma\
y
be thrown about during braking. After use, make sure the tools are cor-
rectly positioned in their housings: there is a risk of injury.
If wheel bolts are supplied in the tool kit, only use these bolts for th\
e
emergency spare wheel: refer to the label affixed to the emergency spare wheel.
The jack is designed for wheel changing purposes only. Under no circumstances
should it be used for carrying out repairs underneath the vehicle or to \
gain access
to the underside of the vehicle.
1
2
34
Wheelbrace 4This is used to tighten/loosen the wheel
bolts and, depending on the vehicle, to
access the emergency spare wheel.
1
2
3
4

JauneNoir Noir texte
5.3
ENG_UD24468_1
Crevaison (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
PUNCTURE (1/2)
In the event of a puncture,
depending on the vehicle,
you will have:
An emergency spare wheel or tyre in-
flation kit (refer to the information on the
following pages).
If the emergency spare wheel has been stored for several years, have it \
checked by your Dealer to ensure that it is safe to use.
Vehicle fitted with an emergency spare wheel that differs from the
other wheels:
– Never fit more than one emergency spare wheel to the same vehicle.
– As the punctured wheel is wider than the emergency spare wheel, the vehicle’s ground clearance is reduced.
– Replace the emergency spare wheel as soon as possible with a wheel ident\
i- cal to the original one.
– When this is fitted to the vehicle, which must only be a temporary measu\
re, the driving speed must not exceed the speed indicated on the label on the wh\
eel.
– Fitting an emergency spare wheel may alter the way the vehicle usually runs. Avoid sudden acceleration or deceleration and reduce your speed when cor-\
nering.
– If you need to use snow chains, fit the emergency spare wheel to the rear axle and check the tyre pressure.

JauneNoir Noir texte
5.4
ENG_UD24468_1
Crevaison (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
Emergency spare wheel 2
This is stored in cage 4 under the floor
at the rear of the vehicle.
To access the emergency spare
wheel
– Open the tailgate;
– Undo the nut with wheelbrace 1
stored in the boot;
– Detach the cage 4 using handle 3;
– Release the emergency spare wheel.
PUNCTURE (2/2)
To store the wheel in the cage
– Make sure the wheel is correctly po-sitioned in the cage 4, valve facing
down.
– Re-attach the subframe using handle 3 and retighten the nut using
spanner 1 to refit the assembly.
– Make sure it is correctly locked.
If the cage 4 cannot be re-attached, this
means that the wheel is poorly posi-
tioned. If this happens, open the cage,
push the wheel in as far as it will go and
close again.
1
2
34
1
Do not leave the tools un-
secured inside the vehicle
as they may come loose
under braking. After use,
make sure the tools are correctly
positioned in their housings: risk of
injury.
If wheel bolts are supplied in the
tool kit, only use these bolts for the
emergency spare wheel: refer to the
label affixed to the emergency spare
wheel.
The jack is designed for wheel
changing purposes only. Under no
circumstances should it be used for
carrying out repairs underneath the
vehicle or to gain access to the un-
derside of the vehicle.
Do not touch the exhaust as
it could burn.

JauneNoir Noir texte
5.5
ENG_UD33465_1
Kit de gonflage des pneumatiques (X67 - X92 - Dacia)
ENG_NU_975-6_X92_Dacia_5
TYRE INFLATION KIT (1/6)
The kit repairs tyres with
tread A damaged by ob-
jects smaller than 4 mm. It
cannot repair all types of
puncture, such as cuts of more than
4 mm, or cuts in tyre sidewall B etc.
Ensure also that the wheel rim is in
good condition.
Do not pull out the foreign body
causing the puncture if it is still in
the tyre.
Do not attempt to use the
inflation kit if the tyre has
been damaged as a result
of driving with a puncture.
You should therefore carefully check
the condition of the tyre sidewalls
before any operation.
Driving with underinflated, flat or
punctured tyres can be dangerous
and may make the tyre impossible
to repair.
This repair is temporary
A tyre which has been punctured
should always be inspected (and re-
paired, where possible) as soon as
possible by a specialist.
When replacing a tyre repaired with
this kit, you must consult a special-
ist. When driving, vibration may be
felt due to the presence of the repair
product injected into the tyre.The kit is only approved for
inflating the tyres of the ve-
hicle originally equipped
with the kit.
It must never be used to inflate
the tyres of another vehicle, or any
other inflatable object (rubber ring,
rubber boat, etc.).
Avoid spillage on skin when hand-
ling the repair liquid bottle. If drop-
lets do leak out, rinse them off with
plenty of water.
Keep the repair kit away from chil-
dren.
Do not dispose of the empty bottle
in the countryside. Return it to your
approved dealer or to a recycling or-
ganisation.
The bottle has a limited service
life which is indicated on its label.
Check the expiry date.
Contact an approved dealer to re-
place the inflation tube and repair
product bottle.
A
B

JauneNoir Noir texte
5.6
ENG_UD33465_1
Kit de gonflage des pneumatiques (X67 - X92 - Dacia)
ENG_NU_975-6_X92_Dacia_5
TYRE INFLATION KIT (2/6)
Inflation kit C
Depending on the vehicle, in the event
of a puncture, use the kit C located in
the boot.
Before using this kit, park
the vehicle at a sufficient
distance from traffic, switch
on the hazard warning
lights, apply the handbrake, ask all
passengers to leave the vehicle and
keep them away from traffic.
Open the kit, remove caps 1 and 3 (it is
essential not to remove the cap from
the bottle) then screw bottle 2 to its
base 3.
With the engine running and the
handbrake applied,
– unscrew the valve cap on the wheel concerned and screw the inflation
adapter 6 onto valve;
– connect adapter 8 to accessories
socket 9 on the dashboard of the ve-
hicle;
9
1234
5
6
78
C
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.

JauneNoir Noir texte
5.9
ENG_UD33465_1
Kit de gonflage des pneumatiques (X67 - X92 - Dacia)
ENG_NU_975-6_X92_Dacia_5
With the engine running and the
handbrake engaged:
– unroll the hose from the container;
– connect the compressor hose 13 to
the container inlet 18;
– depending on the vehicle, connect the container 18 to the compressor
from the container recess 17;
– unscrew the valve cap on the rel- evant wheel and screw on the con-
tainer’s inflation adapter 11;
– adapter 12 must be connected to
the vehicle accessories socket;
– press switch 14 to inflate the tyre to the recommended pressure (please
refer to the information on “Tyre
pressure”); – after a maximum of 15 minutes, stop
inflating and read the pressure (on
pressure gauge 15).
Note: while the container is empty-
ing (approximately 30 seconds), the
pressure gauge 15 will briefly indi-
cate a pressure of up to 6 bar. The
pressure will then drop.
– adjust the pressure: to increase it, continue inflation with the kit; to
reduce it, press button 16.
If a minimum pressure of 1.8 bar is
not reached after 15 minutes, repair
is not possible; do not drive the ve-
hicle but contact an approved dealer.
TYRE INFLATION KIT (5/6)
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.
Before using this kit, park
the vehicle at a sufficient
distance from traffic, switch
on the hazard warning
lights, apply the handbrake, ask all
passengers to leave the vehicle and
keep them away from traffic.
Inflation kit D
Depending on the vehicle, in the event
of a puncture, use the kit D located in
the boot or underneath the boot carpet.
1112
13
14
15
17
18
D
16

JauneNoir Noir texte
5.11
ENG_UD24470_1
Enjoliveurs - Jantes (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
WHEEL TRIM - WHEELS
Wheel trim with concealed
wheel bolts
Remove the wheel trim using the
hubcap tool 1, by inserting the tool into
valve recess 2.
To refit the wheel trim, align it with
valve 2. Push the retaining hooks in
fully, starting with side A near the valve,
followed by B and C, finishing at D op-
posite the valve.
1
A
BC
D
2
Wheel trim with visible wheel
bolts
To remove it without removing the
wheel, press it at the points indicated
by the arrows.
Turn it so that the retaining brackets
holding it in place behind the wheel
bolts are released.
To refit the hubcap, proceed in reverse
order.
Anti-theft bolts
If you use anti-theft bolts,use the in-
structions on the inside of the wheel
trim to position the bolts (wheel trim
may not be able to fit).

JauneNoir Noir texte
5.12
ENG_UD34859_3
Changement de roue (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
Place the jack 4 horizontally; the jack
head must be lined up with the sill 1
closest to the wheel concerned, as
shown by arrow 2.
Crank up the jack 4 by hand at first to
align the base plate (which should be
inclined further inwards than the jack
head).
Turn the wheelbrace until the wheel lifts
off the ground.
CHANGING A WHEEL (1/2)
Vehicles equipped with a jack
and wheelbrace
If necessary, remove the hubcap.
Use the wheelbrace 3 to slacken off
the wheel bolts. Fit it so that you press
downwards rather than pulling up-
wards.
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.
To prevent any risk of injury
or damage to the vehicle,
only crank the jack until the
wheel you are replacing is
a maximum of 3 centimetres off the
ground.
If the vehicle is not equipped with a
jack or wheelbrace, you can obtain
these from your approved dealer.Switch on the hazard warn-
ing lights.
Keep the vehicle away from
traffic and on a level surface
where it will not slip.
Apply the parking brake and engage
a gear (first or reverse).
Ask all passengers to leave the ve-
hicle and keep them away from traf-
fic.
1
23
4

JauneNoir Noir texte
5.13
ENG_UD34859_3
Changement de roue (X92 - Renault)
ENG_NU_975-6_X92_Dacia_5
Undo the bolts and take off the wheel.
Fit the emergency spare wheel on the
central hub and turn it to locate the
mounting holes in the wheel and the
hub.
If bolts are supplied with the emergency
spare wheel, only use these bolts for
the emergency spare wheel.
Tighten the bolts, checking that the
wheel is correctly positioned on its hub
and lower the jack.
With the wheel on the ground, tighten
the bolts fully and have the tightness
of the bolts checked (tightening torque:
110 N.m) and the emergency spare
wheel pressure checked as soon as
possible.
CHANGING A WHEEL (2/2)
If you have a puncture, re-
place the wheel as soon
as possible. A tyre which
has been punctured should
always be inspected (and repaired,
where possible) by a specialist.
Anti-theft bolts
If you use anti-theft bolts, please
refer to the instructions given on
the interior of the wheel trim to posi-
tion the bolts (wheel trim may not be
able to fit).

JauneNoir Noir texte
5.14
ENG_UD24472_1
Pneumatiques (X92 - Renault)ENG_NU_975-6_X92_Dacia_5
TYRES (1/3)
Tyre and wheel safety
The tyres are the only contact between
the vehicle and the road, so it is essen-
tial to keep them in good condition.
You must make sure that your tyres
conform to local road traffic regulations.
When they need to be re-
placed, only tyres of the
same make, size, type and
profile should be used.
Tyres fitted to the vehicle should
either be identical to those fitted
originally or conform to those
recommended by your approved
Dealer.
Maintaining the tyres
The tyres must be in good condition
and the tread form must have sufficient
depth; tyres approved by our Technical
Department have wear warning strips 1
which are indicators moulded into
the tread at several points. When the tyre tread has been worn
to the level of the warning strips, they
become visible
2: it is then neces-
sary to replace your tyres because the
tread rubber is now only 1.6 mm deep
at most, resulting in poor road hold-
ing on wet roads.
An overloaded vehicle, long journeys
by motorway, particularly in very hot
weather, or continual driving on poorly
surfaced minor roads will lead to more
rapid tyre wear and affect safety.
Incidents which occur when
driving, such as striking the
kerb, may damage the tyres
and wheel rims, and could
also lead to misalignment of the
front or rear axle geometry.
In this case, have the condition of
these checked by an approved
dealer.
1
2