power DACIA SOLENZA 2004 User Guide

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 7
Power train group
Dismount the hydro-elastic buffer nut (on
the right side).
Remove the power train and place it on a
support.
Disco n nect th e pr e ssu re controller
connector for power steering.
Dismo unt :
- hoses from oil reservoi r for power
s teering by means of pliers MOT 1202-01;
- high pressure pipe from the power
steering pump.
Dismount the refrigerant fluid pipes from
compressor (vehicles with AC unit).
Sustain the power t rain by means of the
two liftin g supports u sing a mobile lifting device
(mobile crane). Dismount the four attachment screws of the
power train support-battery and the elastic bu ffer
nut (9).
9
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 8
Power train group
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Tighten the screws and nuts to the required moment.
Perform: -filling and purging of the cooling circuit (see chapter 19”Filling a nd purging”);
-f illing with oil of the engine and gearbox;
-f illing of the power steering circuit (see chapter 05 “ Draining-Filling)- for vehicles
equipped with power steering;
-filling of the air conditioning circuit with refrigerant fluid HFC 134a (see chapter 62 “Air
conditioning”). Adjust the clutch pedal stroke (see chapter 37”Clutch control adjustment”).
REMARK:
At each operation implying battery dismounting, when reconnecting the battery,
introduce the radio code, which is written on the vehicle-purchasing invoice.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 10
ENGINE UNFITTING
Dismo
unt :
- alternator and its belt;
- oil dipper guide;
- induction coil, after its electric co nnector
and spark plugs cables have been disconnected.
ENGINE FITTING
Perform the dismounting operations in the
reverse order.
Tighten the screws and nuts to the required
moment.
Se paration – Unfitting
Di sconnect the electri c connectors and
dismount the engine wiring.
Dismou nt then:
- valve body;
- injection ramp;
-clutch disc and mechanism;
-e ngine flywh eel;
- intake manifold;
- thermal screen and exhaust manifold;
- water inlet pipe;
- thermostat support.
For the veh i cles equi ppe d wi t h a i r
conditioning unit and /or power steeri ng
d ismount additionally:
-driving belt tensioner;
- compressor belt;
- compressor electric connector;
- compressor;
- compressor support and intermedi ary
support.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 12
NO.DE NOM I NAT ION SERVICE DACI A
CODE ITEM NO
1O il plug wrench MOT 1018 1001101 800
2D evice for mounting the camshaft sealing gasket MOT 1127-01 1001112701
3Devic e for mounting crankshaft sealing gasket towards flywheel MOT 1129-01 1001112901
4Devic e for distribution belt tensioning MOT 1135-01 1001113501
5P liers for elastic clips MOT 1202-01 1001120 201
6Su itcase for petrol pressure checking MOT 1311-01 1001131101
7 Connection “J” MOT 1311-04 1001131104
8 Connection “K” MOT 1311-05 1001131105
9D evice for conne ction dismounting MOT 1311-06 1001131106
10 Pliers for valves oil seal ring dismounting MOT 1335 1001133 500
11 Device for checking the belt tensioning MOT 1505 1001150 500
12 Device for pi ston shaft mounting MOT 574-22 1001 0574 22
13 Sector for flywheel fixing MOT 582 1001 0582 00
14 Device for distribution gear blocking MOT 799-01 1001 0799 01
15 Device for mounting the crankshaft sealing gasket towards distribution MOT 550 1001 0550 00
16 Wrench for rockers adjustment MOT 567-01 1001 0567 01
17 Wrench for oil filter MOT 555 1001 0555 00
18 Device for power train sustaining MOT 545 1001 0545 00
19 Device for jackets maintaining MOT 484 1001 0484 00
or
Jackets maintaining clamps MOT 588 1001 0588 00
20 Comparing support MOT 251-01 1001 0251 01
21 Plate for measurement of cylinder jackets over-height MOT 252-01 1001 0252 01
Special tools
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 21
CYLINDER HEA D DISMOUNTING
Drain the oil from the engine.
Dismount :
- wiring from the engine;
- compressor and/or power steering pump ( for vehicles equipped with air conditioning
unit and/or power steering); -compressor support and/or power steering pump support;
- alternator and its belt.
Dismounting – Remounting
Block the engine flywheel by means of the
MOT 582 device .
Dismou nt :
- oil dipper rod support;
- alternator belt tightening clamp;
-cr ankshaft pulley or pulleys ;
- pulley hub;
- distribution belt casings.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 38
2. Camshaft gear with marks
Rotate the engine until is reaching the Upper
Dead Point (cylinder 1 at ignition), and then con-
tinue until first item:
- adjust : exhaust 1
exhaust 3
- at second item :
-adjust : admission 1
admission 3
- at third item :
- adjust : exhaust 2
exhaust 4
- at fourth item :
- adjust : admission 2
admission 4
Dismounting – Remounting
Continue to mount:
- cylinder head cover equipped with a ne w cylinder head gasket, tighten the attachment
sc rews to the required moment of 1 daNm;
- water inlet pipe and the oil dipper guide (with new sealing rings);
- distribution casings;
-cr ankshaft pulley or pulleys; tighten the pulley hub screw to the required moment of 2
daN m, then to 68° ± 6°.
ATTENTION!
If the screw is not properly tighten, this may unloose, which may lead to the oil pump
no n-drive and to the distribution derangement, consequently to engine damaging.
- intake manifold and exhaust manifold, tighten the attachmen t screws to the required mo-
ment of 2.5 daNm;
- compressor and/or power steering support;
- alternator (see chapter 16”Alternator”);
- compressor- for vehicles equipped with air conditioning (see chapter 62 “Air condition-
ing”); -power steering pump-for vehicles equipped with power steering (see chapter 36 “Power
steering pump”);
-belt or accessories belt according to the method described in chapter 07” Accessories
b elt tensioning”.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 42
Multi-purpose support
TIGHTENI NG MOMENTS (daNm)
Sup port attachment screws 4
Sup port upper attachment screws 2
DISMOUNTIN G
Place t he vehicle on a two-column elevator.
Disconnect the battery.
Dismount :
-compressor (see chapter 62”Air
conditioning ”) for vehicles equipped with a ir
conditioning unit; -power steering pump (see chapter 36 “
Power steering pump”) for vehicles equipped
with power steering.
- Dismoun t the support attachment screws.
2
2
REMOU NT I NG
Position the support and pre-tighten the
central screw (1) to the required moment of
0.25 daNm. Mount the others attachment screws.
Tighten to the required moment observing
the sequence shown in the drawing. Remount the other elements by
performing the dismounting operations in the
reverse order.
Supp Support AD S
upport AC/AD
vnx.su

ENGINE E7J-26211
11 - 1
DISTRIBUTION SYSTEMDistribution belt
DISMOUNTIN G
Place the vehicle on a two-column eleva-
tor.
Mount between chassis and cylinder casing,
the MOT. 545 device for sustainin g front part
engine.
TIGHTENING MOMENTS (daNm)
Wheels screws 7.5
C rankshaft pulley screw 2+68
0 ± 60
Te nsioning roller nut 5
R ight support screws 6.2
Hydro-elastic buffer nut 3.7
Dismo unt :
-r ight front wheel;
-r ight pendular suspension support;-
accessories belt ( for vehicles provided
with air conditioning and/or power steering; -alternator’s belt;
-cr ankshaft’s pulley or pulleys and their
hub ; -distribution casings.
vnx.su

ENGINE E7J-26211
11 - 2
DISTRIBUTION SYSTEMDistribution belt
Set the engine at setting poi nt (see method described in chapter 10 “ Engine assembly”,
page 10 –19). Loosen the tensioning roller nut.
Dismount the distribution belt.
REMOU NT I NG
Mount a new distribution belt.
Tension the distribution belt to a value of 145 – 185 Hz by means of the MOT 1505 device
(see the method described in c hapter 10 “ Engine assembly”, page 10 –33 ).
Perform the dismounting operations in the reverse order.
Tighten to the required moment the screws.
Remount the pulley for accessories belt (for vehicles equipped with air conditioning and/or
power steering). Obligatory tighten the screw of the crankshaft pulley hub to the required moment of 2 daNm
plus an angle of 68° ± 6 °
Mount and tension the alternator belt and the accessories belt, observing the method for belts
tensioning described in chapter 07 “ Accessories belts tensioning “.
The belts te nsioning values are:
Alternator belt 253 – 273 Hz
Co mpressor belt 150 – 155 Hz
Power steering pump belt 151 – 161 Hz
Co mpressor / power steering pump belt 214 – 230 Hz
vnx.su

ENGINE E7J-26211
11 - 4
DISTRIBUTION SYSTEM
56
Cylinder head gasket
Dismount the hoses from the thermostat sup-
port.
Dismou nt :
- compressor (see chapter 62 “Air con-
ditioning”); -power steering pump (see chapter 36”
Power steering pump );
- alternator (see chapter 1 6 “Alterna-
tor” ); -
oil gauge guide;
- thermal screen;
- multi-purpose support;
- exhaust manifold.
Dismo unt :
- cylinder head screws except the screw
corresponding to A position, which is to be
loosen, then rotate the cylinder head around the
screw remained not-dismounted; - cylinder head.
vnx.su