relay DACIA SOLENZA 2004 User Guide

IGNITION AND INJECTION
17
17 - 37
DF038
P RESENT
OR
ME MO RIZEDDOWNSTREAM OXYGEN SENSOR HEATING CIRCUIT
1DEF : Open circuit or short-circuit
CO : open circuit
CC.O : shot circuit at mass
CC.1 : short circuit at + 12 V.
Perform the operations from “recommendations” for repara tion confirmation.
Fix a ny other possible failures.
Erase the failures memoriz ed by the injection computer.
Perform a conformity checking by means of the CLIP tester.AF TER
REPARATION
Conditions for diagnostic appl ication for memorized failure :
- Start the engine and ensure tha t state “ ET03: downstream O2 sensor
h eating” is active wait for an engine fan starting, and then perform a slight
acceleration for one minute.
- Or act upon the actuator control “ AC262: downstream O2 sensor heating ”
* If the failure is memorized with OBD indicator on, check in the context part,
if state “ET288 : Downstream oxygen se nsor heating circuit” corresponding
to the OBD indicator lighting request is affirmative. In this case, proceed as
per bellow mentioned method.
RE COM M E NDAT IONS
C
heck the connection and the connector state of the oxygen sensor.
C hange the connector if necessa ry.
C heck the heating resistance of th e oxygen sensor.
Refer to chapter ” Help” in order to compare the resistance-meas ured value with the recommend ed
one.
R eplace the sensor if necessary.
C heck the presence of +12 Volts on A pin of the oxygen sensor.
Fi x the ele ctric connection between oxygen sensor and the actuators relay, if necessa ry
C onnect the 90 ways terminal box instead of the injection computer then check the insula tion and
continuity on line: :
Pin 65 injection computer > pin B oxygen sensor
Fix if necessary
If the proble m is persisting after these checking, fix the other failures then perform the conformity
checking.
Diagnostic – Failures interpretation
vnx.su

IGNITION AND INJECTION
17
17 - 40
DF 052
P RESENT
OR
ME MO RIZED
Perform the operations from ” recommendations” for reparation confir mation
Fix a ny other possible failures
Erase the failures memoriz ed by the injection computer.
Perform a conformity checking by means of the CLIP tester.
AF TER
REPARATION
C heck the connection and condition of the injector 1 connector.
R eplace the connector if necessary.
C heck the injector resistance. Refer to chapte r “Help” in order to compare the resistance values.
R eplace the injector if necessary.
When setting the contact on, check the presence of supplying +12 V on pin 1 of the injector 1.
Fix, if necessary the electric routing up to actua tors relay.
C onnect the 90 ways terminal box instead of the injection computer the n check the insulation and
continuity on line:
pi n 59 injection computer > pin 2 injector 1
Fix if necessary.
If after these checking the problem is persisting, treat the other failures then perform the conformity
checking
RE COM M E ND AT IONS
Conditions for diagnostic appl
ication to memorized failure:
Start the engine and especially stop it immediately the failure is becoming
pres ent, so t hat catalyst-dama ging risk is avoide d.
In case of failures addition, treat as most important, fai lure “ DF009 act uators
relay control circuit”
* If the failure is memorized with OBD indicator on, check in the conte xt
part, if state “ET278 : Cylinder injector circuit” corresponding to the OBD
i ndicator lighting request is affirmative. In this case, proceed as per bellow
m entioned method.
Diagnostic – Failures interpretation
CYLINDER 1 INJECTOR CIRCUIT
1. DEF Open circuit or short-circuit
CO : open circuit
CC.O : shot circuit at mass
CC.1 : short circuit at + 12 V.
vnx.su

IGNITION AND INJECTION
17
17 - 41
Perform the operations from ” recommendations” for reparation confirmation.
Fix any other possible failures.
Erase the failures memoriz ed by the injection computer.
Pe rform a conformity checking by means of the CLIP tester.
AF
TER
REPARATION
DF 053
P RESENT
OR
ME MO RIZED
Check the connection and condition of the injector 2 connector.
R eplace the connector if necessary.
C heck the injector 2 resistance. Refer to chapte r “Help” in order to compare the resistance values.
R eplace the injector if necessary.
When setting the contact on, check the presence of supplying +12 V on pin 1 of the injector 2.
Fix, if necessary the electric routing up to actua tors relay.
C onnect the 90 ways terminal box instead of the injection computer then check the in s u la t ion and
continuity on line :
pin 90 injection computer > pin 2 injector 2
Fi x if necessary.
If after these checking the problem is persisting, treat the other failures then perform the
conformity checking.
RE CO MMENDATIONS
Conditions for diagnostic appl ication to memorized failure:
St art the engine and especially stop it immediately the failure is becoming
pres ent, so th at catalyst-dama ging risk is avoide d.
In case of failures addition, treat as most important, failure “ DF009 act uators
relay control circuit”
* If the failure is memorized with OBD indicator on, check in the context part,
if state “ET279 : Cylinder 2 injector circuit” corresponding to the OBD
i ndicator lighting request is affirma tive. In this case, proceed as per bellow
m entioned method
Diagnostic – Failures interpretation
CYLINDER 2 INJECTOR CIRCUIT
1. DEF : Open circuit or short-circuit
CO : open circuit
CC.O : shot circuit at mass
CC.1 : short circuit at + 12 V.
vnx.su

IGNITION AND INJECTION
17
17 - 42
DF 054
P RESENT
OR
ME MO RIZEDCYLINDER 3 INJECTOR CIRCUIT
1 DEF : Open circuit or short-circuit
CO : open circuit
CC.O : s hot circuit at mass
CC.1 : s hort circuit at + 12 V.
RECOMMENDATIONS
Perform the operations from ” recommendations” for reparat ion confirmation
Fi x any other possible failures
Erase the failures memoriz ed by the injection computer.
Pe rform a conformity checking by means of the CLIP tester.AF TER
REPARATION
Conditions for diagnostic appl ication to memorized failure:
Start t he engine and especially stop it immediately the failure is becoming
presen t, so that catalyst-dama ging risk is avoide d.
In case of failures addition, treat as most important, failure “ DF009 actuators
relay control circuit”.
* If the failure is memorized with OBD indicator on, check in the context part,
if state “ET280 : Cylinder 3 injector circuit” corresponding to the OB D indicator
lighting request is affirma tive. In this case, proceed as per bellow me ntioned
met hod.
C heck the connection and condition of the injector 3 connector.
R eplace the connector if necessary.
C heck the injector 3 resistance. Refer to chapter “Help” in order to compare the resistance values.
R eplace the injector if necessary.
When setting the contact on, check the presence of supplying +12 V on pin 1 of the injector 3.
Fix, if necessary the electric routing up to actua tors relay.
C onnect the 90 ways terminal box instead of the injection computer then check the in s u la t ion and
continuity on line:
pin 60 injection computer > pin 2 injector 3
Fi x if necessary.
If afte r these checking the problem is persisting, treat the other failures then perform the conformity
checking.
Diagnostic – Failures interpretation
vnx.su

IGNITION AND INJECTION
17
17 - 43
Perform the operations from ” recommendations” for reparation confirma tion.
Fi x any other possible failures.
Erase the failures memoriz ed by the injection computer.
Pe rform a conformity checking by means of the CLIP tester.
AF
TER
REPARATION
CYLINDER 4 INJECTOR CIRCUIT
1. DEF : Open circuit or short-circuit
CO : open circuit
CC.O : s hot circuit at mass
CC.1 : s hort circuit at + 12 V.
DF 055
P RESENT
OR
MEMO RIZED
Conditions for diagnostic appl ication to memorized failure:
Start the engine and especially stop it immediately the failure i s becoming
present, so that catalyst-dama ging risk is avoide d.
In case of failures addition, treat as most important, failure “ DF009
actua tors relay control cir cuit”
* If the failure is memorized with OBD indicator on, check in the context
part, if state “ET281 : Cylinder 4 injector circuit” corresponding to the
OBD indicator lighting request is affirmative. In this case, proceed as per
bellow mentioned method
C heck the connection and condition of the injector 4 connector.
R eplace the connector if necessary.
C heck the injector 4 resistance. Refer to chapter “Help” in order to compare the resistance values.
R eplace the injector if necessary.
When setting the contact on, check the presence of supplying +12 V on pin 1 of the injector 4.
Fix, if necessary the electric routing up to actua tors relay.
C onnect the 90 ways terminal box instead of the injection computer the n check the insulation and
continuity on line :
pi n 89 injection computer > pin 2 injector 4
Fi x if necessary.
If after these checking the problem is persisting, treat the other failures then perform the conformity
checking
Diagnostic – Failures interpretation
RE COMMENDATIONS
vnx.su

IGNITION AND INJECTION
17
17 - 47
DF 061
P RESENT
OR
ME MO RIZEDCYLINDERS 1-4 IGNITION COIL CIRCUIT
1.DEF : Open circuit or short-circuit
CO : Open circuit
CC. O : Short-circuit at mass
CC.1 : S hort-circuit at +12 volts
Conditions for diagnostic appl ication to memorized failure:
Start t he e ngine a nd stop it immediately as the failure is oc curring as being
prese nt (risk for catalyst) or rota te de engine with the starter, without starting it,
for 10 seconds.
In case of failures addition, treat as most important, failure “ DF345 : Supply 5
volts potenti ometers or sensors “ and failure “DF261: Fuel pump relay circui t”,
if it is /they are present
* If the failure is memorized with OBD indicator on, check in the context part, if
st ate “ET282 : Ignition coil 1-4 circuit” corresponding to the OBD indicator
lighting request is affirmative. In this case , proceed as per bellow mentioned
met hod
C heck the connection and condition of the coil connector .
R eplace the connector if necessary.
C heck the resistance of the coil resistance of c ylinders 1-4. Refer to chapte r
“Help” in order to compare the measured resistance values with the recommended
one .
R eplace the coil if necessary.
Check the +12 Volts supply existence after fue l pump relay, at pin C of the coi l.
If it is necessary, apply the methodology for failure diagnostic “DF261”
C onnect the 90 ways terminal box instead of the injection computer the n check
t he insulation and continuity on line:
pin 32 injection computer > pin A ignition coil.
Fi x if necessary.
If the problem is persisting after the se checking, treat the other failures then
perform the conformity checking.
RECOMMENDATIONS
Pe rform the operations from ” recommendations” for reparation confirma tion.
Fi x any other possible failures
Erase the failures memoriz ed by the injection computer.
Pe rform a conformity checking by means of the CLIP tester.
AF
TER
REPARATION
Diagnostic – Failures interpretation
vnx.su

IGNITION AND INJECTION
17
17 - 48
Diagnostic – Failures interpretation
DF 062
P RESENT
OR
ME MO RIZED CYLINDERS 2-3 IGNITION COIL CIRCUIT
1.DEF : Open circuit or short-circuit
CO : Open circuit
CC. O : Short-circuit at mass
CC.1 : S hort-circuit at +12 volts
Conditions for diagnostic appl ication to memorized failure:
Start t he engine a nd stop it immediately as the failure is occurring as be ing
prese nt (risk for catalyst) or rota te de engine with the starter, without starting
it, for 10 seconds.
In case of failures addition, treat as most important, failure “ DF345 : Supply 5
volts potentiometers or sensors “ and f ailure “DF261: Fuel pump relay
circuit ”, if it is /they are present.
* If the failure is memorized with OBD indicator on, check in the context part, if
st ate “ET283 : Ignition coil 2-3 circuit” corresponding to the OBD indicator
lighting request is affirmative. In this case , proceed as per bellow me ntioned
met hod.
C heck the connection and condition of the coil connector .
R eplace the connector if necessary.
C heck the resistance of the coil resistance of c ylinders 2 and 3. Refer to
chapte r “ Help” in order to compare the measured resistance values with the
recommended one.
R eplace the coil if necessary.
Check the +12 Volts supply existence after fuel pump relay, at pin C of the
coil.
If it is necessary, apply the methodology for failure diagnostic “DF261”.
C onnect the 90 ways terminal box instead of the injection computer then check
t he insulation and continuity on line:
pin 1 injection computer > pin B ignition coil.
Fix if necessary..
If the problem is persisting after these checking, treat the other failures then
perform the conformity checking.
RECOMMENDATIONS
Pe rform the operations from ” recommendations” for reparation confirma tion.
Fi x any other possible failures.
Erase the failures memoriz ed by the injection computer.
Pe rform a conformity checking by means of the CLIP tester.
AF
TER
REPARATION
vnx.su

IGNITION AND INJECTION
17
17 - 56
Diagnostic – Failures interpretation
DF 261 FUEL PUMP RELAY CIRCUIT
P RESENT 1. DEF Supply failure + after relay
OR 2. DEF Open circuit or short-circuit
ME MO RIZED
If failure “DF345 : Supply 5 volts potentiometers and sensor s” is
present or memori zed, it must be treated as most important .
Conditions for diagnostic appl ication at memorized failure:
Se t the contact on, then enter in dia logue with the computer
Or activation of the actua tor control “ AC 010 : Fuel pump relay”.
RECOMMEND ATIONS REMARK : This failure is most important. So it must be treated before
t he next ones.
* If the failure is memorized with OBD indicator on, check in the context
part, if state “ET241 : Fuel pump control cir cuit” corresponding to the
OBD indicator lighting request is affir mative. In this case , proceed as
per bellow mentioned method
1. DEF RECOM MENDAT IONS It is a failure on the power circuit of the fuel
pump relay.
C heck the electric continuity f the idleness contact.
Me nd if necessary.
C heck the connection and con dition of the fuel pump relay connector .
R eplace the connector if necessary.
C heck the presence of the +12 volts supply at pole 3 of the fuel pump relay
Me nd if necessary.
C heck with the contact set on a nd acting the actuator c ontrol “AC010 : Fuel pump relay”, the
prese nce of +12 V supply at pole 5 of the fuel pump relay.
R eplace the relay if necessa ry
C heck the insu lation and cont inuity of the connections between:
Pole 5 fuel pump relay > pi n C ignition coil
Pole 5 fuel pump relay > fuel pump
Me nd if necessary.
If the problem is persisting after these checking, treat the other failures then perform the
conformity checking.
Perform the operations from ” recommendations” for reparation confirma tion.
AF TER Fix any other possible failures
REPARATION Erase the failures memoriz ed by the injection computer.
Perform a conformity checking by means of the CLIP tester.
vnx.su

IGNITION AND INJECTION
17
17 - 57
DF 261
CONTINU AT I O N
2. DEF RECOM MENDAT IONS It is a failure on the power circuit of the fuel
pump relay.
C heck the connection and condition of the fuel pump relay connector .
R eplace the connector if necessary.
Check, with the contact set non, the pr e sence of the +12 volts supply at pole 1 of the fuel pump
relay.
M end if necessary.
C heck the fuel pump rela y coil.
R eplace the fuel pump rela y if necessary.
Check the insu lation and continuity of the line:
Pin 68 injection computer > pole 2 fuel pump relay
M end if necessary.
If the problem is persisting after these checking, treat the other failures then perform the conformity
checking.
P erform the operations from ” recommendations” for reparation confirma tion.
AF TER Fix any other possible failures
REPARATION Erase the failures memoriz ed by the injection computer.
Perform a conformity checking by means of the CLIP tester.
Diagnostic – Failures interpretation
vnx.su

IGNITION AND INJECTION
17
17 - 58
DF 271 ACTUATORS RELAY EXIT VOLTAGE
P RESENT 1. DEF Open circuit or short-circuit
OR
ME MO RIZED
Conditions for diagnostic appl ication at memorized failure:
Se t the conta ct off and wait until the communication with the computer
is lo st.
RECOMMEND AT IONS
REMARK : If failure “DF009 : Actuators relay control circuit” is
prese nt or memoriz ed, it must be treated as most important, because
th is could be the cause of the failure occurring.
C heck the condition of the battery and of the vehicles electric masses.
M end if necessary.
C heck the connection and condition of the actuators relay connector .
Re place the connector if necessary.
Check with the contact set on, the pr e se nce of the +12 V supply at pole 3 of th e actuators relay.
Fi x the electric routing on the line towards the corresponding fuse .
C heck with the contact set on, the presence of +12 V supply at pole 5 of the actuators relay.
Repl ace the relay if necessa ry
C heck the insu lation and continuity on the line:
Pin 66 injection computer > p ole 5 actuators relay
M end if necessary.
Disconnect one by one the elements (injector, canister purging valve…) and observe the +12 V
s upply at the exit pole 5 of the actuator s relay, in order to identify the damaged one .
Replace the damaged el ement.
P erform the operations from ” recommendations” for reparation confirma tion.
AF TER Fix any other possible failures
REPARATION Erase the failures memoriz ed by the injection computer.
Perform a conformity checking by means of the CLIP tester.
Diagnostic – Failures interpretation
vnx.su