fuel filter DACIA SOLENZA 2004 Repair Manual

ENGINE E7J-26212
12 - 2
F UEL M IXTURE
DENOMINATION PARTICU LARITIES
UCE injection SIEMENS - Connector with 90 ways
In jection system Sequential multi-point
I gnition Static with double coil PINI R (W)
I gnition control led by
RA- C0,52
ΩΩΩΩ

± 10%

































UCE in
jectionRB-C0,52
ΩΩΩΩ

± 10%
R 1 -47,2 KΩΩΩΩ ±
10%
R
2-37,2 KΩΩ ΩΩ ±
10%
Characteristics
Detonation sensor Sagem – piezo-electric type
Tightening moment = 2 daNm.
RPM sensor ELECTRICFIL or SIEMENS
R = 200………….270 Ù
Spa rk plugs SAGEM – Type RFC 52 LZ
Ti ghtening moment = 2.5 –3 daNm
Fuel filter For de-pollution norm 1504
Mounted under the vehicle in front the fuel tank.
Replacement at every scheduled checking
For EURO 00 and EURO 96;
Insi de the fue l tank, attached on the fuel pump assembly.
Do not replace it separately.
Feeding pump Immersed in the fuel tank
For de-pol lution norm 1504:
- Flow: 1.3 l/min. Pressure: 3 bars at 12 V ten sion.
For EURO 00 and EURO 96:
- Pressure: 3.5 bars at 12 V tension.
Pressure regulator For de-pollution norm 1504:
Regulator attached on the injection ramp.
Adjusted pressure : 3 ± 0.2 b ars at zero depression
2.5± 0.2 bars at 500 mbars depression
For EURO 00 and EURO 96:
Mounted inside the fuel tank on the fuel pump assembly.
Adjusted pressure : 3.5 bars
Electro-magnetic Injectors SIEMEN S
R = 14.5 Ù ± 5 % AT 20 º C
Supply + 12V
Step by step engine R
A-D = 53 Ù 10% at 25º C
R
B- C = 53 Ù 10% at 25 ºC
vnx.su

ENGINE E7J-26212
12 - 5
F UEL M IXTURE
TIGHTENING MOMENT (d aN m)
Inlet manifold nuts and screws 2,5
Inlet manifold
32 5 7
416
3
1
42
DISMOUNTIN G
Place the vehicle on a two-columns
elevator. Disconnect the battery.
Dismo unt :
- the air filter assembly;
- the acceleration cable from the body
control lever; - the injection ramp ( see c hapter 13
“Injection ramp”).
Disconnect the electric connectors:
- body position potentiometer ( 1)
- atmospheric pressure sensor (2)
- step-by-step engine (3);
- air temperature sensor( 4)
Disconnect the fuel supply ducts (supply and return)
Disconnect the petrol vapors re-aspiration hose from the inlet manifold.
Uncouple the body control lever and remove the valve body.
Dismount the attachment nuts and screws of the inlet manifold.
Extract the inlet manifold .
REMOU NT I NG
Replace the inlet manifold gaskets.
Tighten at the required moment the inlet manifold nuts and screws, observing the sequence
shown in the drawing.
Perform the dismounting operations in the reverse order.
vnx.su

MOTEUR E7J-26213
FUEL SUPPLY
13 - 2
Fuel ramp
AT T E N T I O N !
When opening the fuel circuit, protect
by means of a gauze piece against petrol
s plashing due to residual pressure.
DISMOUNTIN G
Disconnect the battery.
Dismount the air filter.
Disconnect:
- pipe 1 for fuel supply;
- pipe 3 for fuel return;
- pipe 4 of the pressure controller.
REMARK:
For EURO 00 and EURO 96, the
pre ssure c ontrol ler and return pi pe are
placed in t he fuel tank.
Dismount the attachment screws ( 2) o f the
fuel ramp. Dismount the ramp. In order to dismount an injector, re trieve
the clip 5, and then extract the injector.
R EMOU NT I NG
Replace the annular gaskets from the
injectors bottom; if t he injector has been
dismounted, the gasket from the injector’s
head will be also replaced.
In order that petrol fuel supply and return
connection a re c orrectly m ounted, a ” clic”
must be heard when connecting. Perform the dismountin g operations in the
reverse order.
vnx.su

MOTEUR E7J-26213
FUEL SUPPLY
13 - 4
Supply pressure
MOT. 13 11 -0 6
MOT 1311 -04
MOT 1311 -01
SUPPLY PRESSURE CHECKING
SPECIAL TOOLS
MOT 13 11 – 01 Petrol pre ssure
checki ng ki t
MOT 13 11 – 04 J - connection
MOT 13 11 – 06 Device for
conn ection s
dismounting.
AT T E N T I O N !
When opening the fuel circuit, protect
by means of a gauze piece against petrol
s plashing due to residual pressure from
the supply circuit.
Dismount the air filter.
Disconnect the fuel supply hose.
Connect the MOT 1311-04 device on the
ramp, and then reconnect the fuel supply
piping to the connection.
Mount the manometer 0 ÷ 10 bar and
the flexible hose MOT 1311 – 01.Bridge the terminals
3 and 5 of the fuel pump
relay H, placed in the fuse and relays box.
The measured pressure must be 3.5 bars.
Fo r vehicles with fuel circuit without return
(controller mounted on pump), the pressure is
constant.
vnx.su

ENGINE E7J-26216
16 - 4
ALTERNATOR – STARTER
SPECIAL TOOLS
MOT 1505 Belt tension measurement device
TIGHTENING MOMENTS (daNm)
Upper attachment screw 2,2
Lower attachment screw 5
MOT 1505
Ve
hicles without air conditioning.
DISMOUNTIN G
Place the vehicle on a two-column elevator.
Disconnect the battery.
Disconnect the fuel supply pipe.
Dismo unt :
- air filter;
- oil gauge pipe;
- alternator upper attachment screw;
- alternator’s belt;
- alternator tightening clamp.
Lift the vehicle.
Disconnec t the alternator electric connectors.
Di smount the alternator l ower attachment
screw.
Lower the vehicle.
Remove the alternator through the upper part.
REMOU NT I NG
Perform the dismounting operations in the
reverse order Tighten the alternator driving belt to 263
HZ ± 10% by means of the MOT 1505
device (see the method described in chapter
07 “ Accessories belts tightening”)
Tight e n to t he re qui red m om ent the
alternator’s attachment screws.
Alternator
vnx.su

IGNITION AND INJECTION
17
17 - 52
RECOMMENDATIONS
Diagnostic – Failures interpretation
DF 109
DF 110
P RESENT
OR
ME MO RIZEDPOLLUTED COMBUSTION MISFIRE
DESTRUCTIVE COMBUSTION MISFIRE
St ate ET014 : Recognition of the cylinder 1 must be active, in order to
i dentify each cylinder.
ET093 : combustion misfire on cylinder 1
ET094 : combustion misfire on cylinder 2
ET095 : combustion misfire on cylinder 3
ET096 : combustion misfire on cylinder 4
These w ill provide information regarding failure cause and location.
In this situation, the problem is probably due to an element that can act
only on one cylinder:
- Problem at injector
A cylinder is declared - Problem at spark plug
damaged : ET093 or ET094 - Problem at high voltage cable.
or ET095 or ET096. Before replacement, try the spark plug or cable changing to anothe r
cylinder.
Cy linders 1 and 4 or In this cylinders 2 and 3 declared situation, the proble m is probably
damaged : ET093 and ET 0 96 due to an eleme nt that can act only this pair of cylinders:
or ET094 and ET095. - Problem at ignition coil, at the high voltage part. - Problem at ignition coil, at the control part
In this situation, the problem is probably due to an element tha t can
F our cylinders declared act only on all cylinders:
damaged : ET093 and -Problem at fuel filter
ET094 or ET095 and ET096. -Problem at fuel pump
-Problem on in use fuel type
-Problem of in use spark plugs
In case by using this method the problem is not solved, cons ult the fail ures diagnostic DF109 / DF
1 10 CONTINUA TION
Ensure that all failures are solved. Erase all memorized failures.
There is no need to erase the “adaptive values” memoriz ed by the injection computer.
In order to check the correct reparation of the system, the following conditions must be
AF TER accomplished:
REPARATION - No more electrical failures;
- All “adaptive values” to be memorized by the injection computer;
- Warm engine (minimum 75°C);
- Run at idling, all consumers being in use for 20 minutes (1 minute DF110);
- If the failure is again occurring, repeat the dia gnostic.
vnx.su

IGNITION AND INJECTION
17
17 - 53
Diagnostic – Failures interpretation
DF 109
DF 110
CONTINU AT I O N
ET093 : combustion misfire on cylinder 1
ET094 : combustion misfire on cylinder 2
RE COMMENDATIONSET0 95 : combustion misfire on cylinder 3
ET096 : combustion misfire on cylinder 4
These w ill provide information regarding failure cause and location.
C heck the ignition system ( refer to chapter “Help” ).
Fix it if necessary.
C heck the engine compression.
Fix it if necessary.
C heck the flywheel condition , in order to get a correct information of the engine RPM.
Fix it if necessary.
If no failure has been found, there is a problem on the fuel supply cir cuit.
In this situation the following must be checked:
- Fuel filter
-F uel pressure and flow
-F uel pump condition
-F uel tank cleaning condition]
-I njector s conditions
Mend the fuel supply circuit.
Ensure that all failures are solved. Erase the memorized failures.
There is no need to erase the “adaptive values” memorized by the injection
computer. In order to check the correct reparation of the system, the following
conditions must be accomplished:
AF TER - No more electrical failures.
REPARATION - All “adaptive values” to be memor ized by the injection computer.
- Warm engine (minimum 75°C)
- Run at idling, all consumers being in use for 20 minutes (1 minute
DF110).
vnx.su

IGNITION AND INJECTION
17
17 - 80
PR030 ENRICHING ADAPTATION IN OPERATION
PR031 ENRICHING ADAPTATION AT IDLING
RECOMMEND AT IONS No failure must be present or memorized.
Perform the steps for memorizing the adaptation values by the injection
computer.
Erase the computer memory. A t warm, when idling adjustment, observe the se paramete rs :
- If one of t hese parameters is moving towards the minimal limit, there is not sufficient petrol or there
is t oo much air.
- If one of the se paramete rs is moving towards the minimal limit, there is too much petrol or there is
not sufficient air.
(See chapter “ Enriching adaptive correction) for the exact limit values)
Ensure the cleaning condition and the good operation of :
- fuel filter
- fuel pump
- fuel circuit
- fuel tank
- air supply piping
- air filter
- spark plugs
C heck :
- Engine compressions
- Valves cle arance
- Ignition
Diagnostic – Parameters interpretation
AF TER Restart the conformity checking from the beginning.
REPARATION
vnx.su

IGNITION AND INJECTION
17
17 - 85
ALP 2 STARTING PROBLEMS engine is not starting or is difficulty starting)
RECOMMEND AT IONS Do not consult this diagnostic but before performing a complete
checking by means of the CLI P tester.
Ch eck that starter is well operating
Ch eck there is petrol in the fuel tank (fuel indicator failure).
Ensure that vehic le is supplied with adequate fuel.
Ch eck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
Ch eck the condition of the fuel filter
Ch eck the condition of the fuel tank
Ch eck that fuel tank aeration is taking place.
Ch eck the electric supply of the fuel pump.
Ch eck the good operation of the choke sensor.
Ch eck the motor of the idling regula tor.
In order to unblock it, you may slightly hit it.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
Ch eck the spark plugs and ignition coil condition
Ch eck tha t these eleme nts are specific to that vehicle.
Ch eck that the exhaust route is not clogged and the catalyst is not clogged.
Ch eck the engine compressions
Ch eck the flywheel condition
Ch eck the distribution setting on.
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su

IGNITION AND INJECTION
17
17 - 86
ALP 3 IDLING PROBLEMS (unstable idling)
RECOMMEND AT IONS Do not consult this diagnostic but before performing a complete
checking by means of the CLI P tester.
C heck if there is petrol in the fuel tank (fuel indicator failure)
C heck if the vehic le is supplied with adequate fuel
C heck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
C heck the condition of the fuel filter
C heck the condition of the fuel tank
C heck that fuel tank aeration is taking place.
C heck the connection and the condition of the idling regulator connector.
Re place the connector if necessary.
C heck the motor of the idling regulator
In order to unblock it, you may slightly hit it.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
C heck the spark plugs and ignition coil condition
C heck tha t these eleme nts are specific to that vehicle.
C heck that the exhaust route is not clogged and the catalyst is not clogged.
Check, by means of the oil dipstick, that oil level is not too high.
C heck for lack of sealing at servo-brake (noise).
C heck the intake manifold condition
C heck if the valve body is not clogged
C heck the engine compressions.
C heck the engine flywheel condition
C heck the distribution setting on.
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su